in rpt.conf, (cut and paste ) the [functions] stanza to a seperate file labeled commands.include then delete or comment out all the commands in the stanza and replace with this line "#include commands.include" THEN put all the commands YOU want above and beyond what is required to be standard across everyones nodes 1-5 ilink etc. in the commands.include file. Use (winSCP) to copy the commands.include file to all your nodes and edit each nodes rpt.conf stanza to have the line in [functions] be #include commands.include. For each new system you just you build just add YOUR commands.include file and it will have all the same commands as the others. from my rpt.conf .......... outstreamcmd=/bin/sh,-c,/usr/bin/lame --preset cbr 16 -r -m m -s 8 --bitwidth 16 - - 2> /tmp/stream.status | /usr/bin/ezstream -qvc /etc/ezstream.xml [functions] #include commands.include #include /etc/asterisk/local/localcmds.include [morse] speed=20 ............................ and a copy of a generic commands.include file for you to cut and paste if you wish. root@N8THN:/etc/asterisk# cat commands.include ;commands.include ;Command common acrossed all nodes ;single digit public commands 0=autopatchdn 1=ilink,1 ; Disconnect Link 2=ilink,2 ; Connect Link MOnitor Only 3=ilink,3 ; Connect Link Transieve 4=ilink,4 ; Enter Command Mode on another Node 5=macro,1 ; Macro Prefix 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up ;double digit public commands 70=ilink,5 ; System Status 71=ilink,6 ; Disconnect all Links 72=ilink,7 ; Play Last Node to Key Up 73=ilink,15 ; FULL system Status - all nodes 74=ilink,16 ; Reconnect disconnected links disconnected with disconnect all links command 75=ilink,8 ; Connect Link LOCAL monitor only 76= 77= 78= 79= 80=status,11 ;Force ID LOCAL ONLY 81=status,12 ; GIve Time of Day LOCAL ONLY 82=status,3 ; Give Software Verison 83=status,5 ; Last DTMF User 84=cop,32 ; DTMF TEST 85= 86= 87= 88=cop,55 ;Parrot Once if parrot mode is disabled 89=autopatchup,context=command_process,noct=1,farenddisconnect=1,dialtime=7000,quiet=1; Command Processing 99=cop,6 ; ptt phone mode ; Triple digit control operator /owner codes 900=cop,3 ;disable system 901=cop,2 ;enable system 903=cop,1 ;System warm boot 902= 903= 904=cop,4 ;Test Tone On/Off 905=cop,5 ;dump system variables 906= 907=cop,7 ;Time out timer enable 908=cop,8 ;Time out timer disable 909=cop,9 ;Autopatch enable 910=cop,10 ;Autopatch disable 911=cop,11 ;Link enable 912=cop,12 ;Link disable 913=cop,13 ;Query System State 914=cop,14 ;Change System State 915=cop,15 ;Scheduler Enable 916=cop,16 ;Scheduler Disable 917=cop,17 ;User functions (time, id, etc) enable 918=cop,18 ;User functions (time, id, etc) disable 919=cop,19 ;Select alternate hang timer 920=cop,20 ;Select standard hang timer 921=cop,21 ;Enable Parrot Mode 922=cop,22 ;Disable Parrot Mode 923=cop,23 ;Birdbath (Current Parrot Cleanup/Flush) 924=cop,24 ;Flush all telemetry 925=cop,25 ;Query !!!!last node un-keyed!!!! 926=cop,26 ;Query all nodes keyed/unkeyed 927=cop,27 ;Reset DAQ minimum on a pin 928=cop,28 ;Reset DAQ maximum on a pin 929= 930=cop,30 ;Recall Memory Setting in Attached Xcvr 931=cop,31 ;Channel Selector for Parallel Programmed Xcvr 932= 933=cop,33 ;Local Telemetry Output Enable 934=cop,34 ;Local Telemetry Output Disable 935=cop,35 ;Local Telemetry Output on Demand 936=cop,36 ;Foreign Link Local Output Path Enable 937=cop,37 ;Foreign Link Local Output Path Disable 938=cop,38 ;Foreign Link Local Output Path Follows Local Telemetry 939=cop,39 ;Foreign Link Local Output Path on Demand 940=cop,40 ;IRLP announce Enable 941=cop,41 ;IRLP announce Disable 942=cop,42 ;Echolink announce node # only 943=cop,43 ;Echolink announce node Callsign only 944=cop,44 ;Echolink announce node # & Callsign 945=cop,45 ;Link Activity timer enable 946=cop,46 ;Link Activity timer disable 947=cop,47 ;Reset "Link Config Changed" Flag 948=cop,48 ;Send Page-Tone specs separated by ( ) 949=cop,49 ;Disable incoming connections (control state NOICE) 950=cop,50 ;Enable incoming connections (control state NOICD) 951=cop,51 ;Enable sleep mode 952=cop,52 ;Disable sleep mode 953=cop,53 ;Wake up from sleep 954=cop,54 ;Go to sleep 955=cop,60 ;SEND MDC-1200 Burst 956=cop,56 ;Rx CTCSS Enable 957=cop,57 ;Rx CTCSS Disable 958=cop,58 ;Tx CTCSS On Input only Enable 959=cop,59 ;Tx CTCSS On Input only Disable ; 98 series up to local nodes On Fri, Jan 5, 2018 at 3:31 AM, larry <larry@n7fm.com> wrote:
Can some one point me to a listing of every available command defined that can used with Allstar.
I am have a heck of a time trying to configure my nodes so everything is all the same commands on all my nodes.. It seems whenever there is a different version other than the 1-5 ilink commands there is no standard numbering system between versions or platforms. Realizing that it is up to me to standardize my own system I am about to start from scratch eliminating all the jumble. It would certainly be helpful if there was a COMPLETE command list with explanations of their functions.
Larry - N7FM _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/c gi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- Nathan Hardman nhardman1428@gmail.com N8THN@ARRL.NET