My node consists of an Intel NUC DCCP847DYE PC Which has an Intel Celeron™ Processor 847(1.10 GHz, 2M Cache) It has 3 USB ports and Video / Audio out are supported by 2 HDMI ports which may be part of my problem. • Intel® HD Graphics • Dual HDMI Ports supporting dual independent display Intel® High Definition Audio (Intel® HD Audio) via two HDMI 1.4a outputs supporting 8 channel (7.1) digital audio I am running a single node on this pc. The node is operating a UHF repeater. Two radios. Icom Commercial IC-F420 mobiles via a DMK URI. I loaded ACID and my system ran fine until I rebooted. This is my second attempt at installation. I will include my .conf files below. I have PL tones set on radios but am not using COR/COS. I utilize the software to detect PL to trigger TX/RX. I have a slow blinking green LED on the DMK URI 2-3 flashes per second, when it has failed and is not sending audio to the TX radio(like now). And a nice fast blink pattern when it is working. Ok...Oh the is keying up with a staticy transmission during ID's and when Flash is run in the radio-tune-menu, but not recognizable audio is heard. RPT.CONF [29922] ; Change this to your assigned node number rxchannel=Radio/usb29922 duplex=2 erxgain=-3 etxgain=3 ;controlstates=controlstates scheduler=schedule29922 morse=morse29922 macro=macro29922 functions=functions29922 phone_functions=functions29922 link_functions=functions29922 telemetry=telemetry wait_times=wait-times context = radio callerid = "Repeater" <0000000000> idrecording = |iAE5YY accountcode=RADIO hangtime=100 althangtime=100 totime=170000 idtime=540000 politeid=3000 idtalkover=|iAE5YY unlinkedct=ct2 remotect=ct3 linkunkeyct=ct8 ;nolocallinkct=0 ;eannmode=1 ;connpgm=yourconnectprogram ;discpgm=yourdisconnectprogram ;lnkactenable=0 ;lnkacttime=1800 ;lnkactmacro=*52 ;lnkacttimerwarn=30seconds ;remote_inact_timeout=1800 ;remote_timeout=3600 nounkeyct=0 ;holdofftelem=0 beaconing=0 ; ; *** Status Reporting *** ; ; Uncomment the either group following two statpost lines to report the status of your node to stats.allstarlink.org ; depending on whether you are running ACID or Limey Linux. ; ** For ACID *** statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates ; ** For Limey Linux ** ;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null ;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates ; ; Morse code parameters, these are common to all repeaters. ; [morse29922] speed=18 frequency=800 amplitude=4096 idfrequency=750 idamplitude=1024 [schedule29922] ;dtmf_function = m h dom mon dow ; ala cron, star is implied [functions29922] 1=ilink,1 2=ilink,2 3=ilink,3 4=ilink,4 5=macro,1 70=ilink,5 71=ilink,6 72=ilink,7 73=ilink,15 74=ilink,16 75=ilink,8 80=status,1 81=status,2 6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up 0=autopatchdn ; Autopatch down ;989=cop,4 980=status,3 99=cop,6 ; Place command macros here [macro29922] [telemetry] ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2=|t(660,880,150,2048) ct3=|t(440,0,150,4096) ct4=|t(550,0,150,2048) ct5=|t(660,0,150,2048) ct6=|t(880,0,150,2048) ct7=|t(660,440,150,2048) ct8=|t(700,1100,150,2048) remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000); remotemon=|t(1209,0,50,2048) cmdmode=|t(900,903,200,2048) functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) patchup=rpt/callproceeding [wait-times] telemwait=2000 idwait=500 unkeywait=2000 calltermwait=2000 ; ; This is where you define your nodes which cam be connected to. ; [nodes] ; Note, if you are using automatic update for allstar link nodes, ; no allstar link nodes should be defined here. Only place a definition ; for your locak nodes, and private (off of allstar link) nodes here. 29922 = radio@127.0.0.1/29922,NONE ; Memories for remote bases [memory] ;00 = 146.580,100.0,m ;01 = 147.030,103.5,m+t ;02 = 147.240,103.5,m+t ;03 = 147.765,79.7,m-t ;04 = 146.460,100.0,m ;05 = 146.550,100.0,m USBRADIO.CONF [general] [usb29922] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=136.5 rxctcssfreqs=136.5 txctcssfreqs=136.5 ;rxctcssoverride=0 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=no txlimonly=no txtoctype=no txmixa=composite txmixb=no invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 #includeifexists custom/usbradio.conf IAX.CONF ; Inter-Asterisk eXchange driver definition ; ; [general] bindport=4569 bindaddr=0.0.0.0 disallow=all allow=gsm allow=g726aal2 allow=ulaw jitterbuffer=yes forcejitterbuffer=yes dropcount=2 maxjitterbuffer=4000 maxjitterinterps=10 resyncthreshold=1000 maxexcessbuffer=80 minexcessbuffer=10 jittershrinkrate=1 tos=0x1E autokill=yes delayreject=yes ;iaxthreadcount=30 ;iaxmaxthreadcount=150 register=29922:<PASSWORD OMITTED>@register.allstarlink.org IN EMAIL for SECURITY [radio-proxy] type=user deny=0.0.0.0/0.0.0.0 permit=/255.255.255.255 context=radio-secure-proxy disallow=all allow=g726aal2 transfer=no [radio-proxy-out] type=peer host= username=29922 secret=<OMITTED for SECURITY> auth=md5 disallow=all allow=g726aal2 transfer=no ; Incoming radio connections [radio] type=user disallow=all allow=g726aal2 allow=gsm codecpriority=host context=radio-secure transfer=no ; Incoming phone connections to app_rpt ;[radio-control] ;type=user ;secret=nunya ;disallow=all ;allow=gsm ;codecpriority=host ;context=radio-control ;transfer=no ; Setup for outgoing calls ;[yourprovider] ; This needs to change ;type=peer ;host=127.0.0.1 ;secret=nunya ;auth=md5 ;disallow=all ;allow=gsm ;transfer=no [allstar-sys] type=user context=allstar-sys auth=rsa inkeys=allstar disallow=all allow=ulaw [allstar-public] type=user context=allstar-public auth=md5 secret=allstar disallow=all allow=ulaw allow=gsm EXTENSIONS.CONF [general] static=yes ; These two lines prevent the command-line interface writeprotect=yes ; from overwriting the config file. Leave them here. [globals] HOMENPA=713 [default] exten => i,1,Hangup [radio-secure] exten => 29922,1,rpt,29922 [radio-secure-proxy] exten => 29922,1,rpt,29922|X exten => _0X.,1,Goto(allstar-sys|${EXTEN:1}|1) [pstn-out] exten=_NXXNXXXXXX,1,playback(ss-noservice) exten=_NXXNXXXXXX,2,Congestion [invalidnum] exten=s,1,Wait,3 exten=s,n,Playback,ss-noservice exten=s,n,Wait,1 exten=s,n,Hangup [radio] exten=_X11,1,Goto(check_route|${EXTEN}|1); exten=_NXXXXXX,1,Goto(check_route|1${HOMENPA}${EXTEN}|1) exten=_1XXXXXXXXXX,1,Goto(check_route|${EXTEN}|1) exten=_07XX,1,Goto(parkedcalls|${EXTEN:1}|1) exten=00,1,Goto(my-ip|s|1) [check_route] ; no 800 exten=_1800NXXXXXX,2,Goto(invalidnum|s|1) exten=_1888NXXXXXX,2,Goto(invalidnum|s|1) exten=_1877NXXXXXX,2,Goto(invalidnum|s|1) exten=_1866NXXXXXX,2,Goto(invalidnum|s|1) exten=_1855NXXXXXX,2,Goto(invalidnum|s|1) ; no X00 NPA exten=_1X00XXXXXXX,2,Goto(invalidnum|s|1) ; no X11 NPA exten=_1X11XXXXXXX,2,Goto(invalidnum|s|1) ; no X11 exten=_X11,2,Goto(invalidnum|s|1) ; no 555 Prefix in any NPA exten=_1NXX555XXXX,2,Goto(invalidnum|s|1) ; no 976 Prefix in any NPA exten=_1NXX976XXXX,2,Goto(invalidnum|s|1) ; no NPA=809 exten=_1809XXXXXXX,2,Goto(invalidnum|s|1) ; no NPA=900 exten=_1900XXXXXXX,2,Goto(invalidnum|s|1) ; okay, route it exten=_1NXXXXXXXXX,1,Goto(pstn-out|${EXTEN:1}|1) exten=_X.,2,Goto(invalidnum|s|1) [my-ip] exten=s,1,Set(MYADDR=${CURL(http://myip.vg)}) exten=s,2,Wait,1 exten=s,3,SayAlpha(${MYADDR}) exten=s,4,Hangup [allstar-sys] exten => 0,1,Answer exten => 0,n,System(rm -rf /tmp/allstar-config\; mkdir -p /tmp/allstar-config\;curl -sk -m 20 --retry 1 https://config.allstarlink.org/config/start.sh > /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh ${CALLERID(name)}) exten => 0,n,Hangup exten => _0.,1,Answer exten => _0.,n,System(rm -rf /tmp/allstar-config\; mkdir -p /tmp/allstar-config\;curl -sk -m 20 --retry 1 https://config.allstarlink.org/config/start.sh > /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh ${CALLERID(name)}) exten => _0.,n,Hangup exten => _1.,1,Rpt(${EXTEN:1}|Rrpt/node:NODE:rpt/in-call:digits/0:PARKED|120) exten => _1.,n,Hangup exten => _2.,1,Ringing exten => _2.,n,Wait(3) exten => _2.,n,Answer exten => _2.,n,Playback(rpt/node) exten => _2.,n,Saydigits(${EXTEN:1}) exten => _2.,n,Rpt(${EXTEN:1}|P|${CALLERID(name)}-P) exten => _2.,n,Hangup exten => _3.,1,Ringing exten => _3.,n,Wait(3) exten => _3.,n,Answer exten => _3.,n,Playback(rpt/node) exten => _3.,n,Saydigits(${EXTEN:1}) exten => _3.,n,Rpt(${EXTEN:1}|Pv|${CALLERID(name)}-P) exten => _3.,n,Hangup exten => _4.,1,Ringing exten => _4.,n,Wait(3) exten => _4.,n,Answer exten => _4.,n,Playback(rpt/node) exten => _4.,n,Saydigits(${EXTEN:1}) exten => _4.,n,Rpt(${EXTEN:1}|D|${CALLERID(name)}-P) exten => _4.,n,Hangup exten => _5.,1,Ringing exten => _5.,n,Wait(3) exten => _5.,n,Answer exten => _5.,n,Playback(rpt/node) exten => _5.,n,Saydigits(${EXTEN:1}) exten => _5.,n,Rpt(${EXTEN:1}|Dv|${CALLERID(name)}-P) exten => _5.,n,Hangup [allstar-public] exten => s,1,Ringing exten => s,n,Set(RESP=${CURL( https://register.allstarlink.org/cgi-bin/authwebphone.pl?${CALLERID(name)}) }) exten => s,n,Set(NODENUM=${CALLERID(number)}) exten => s,n,GotoIf($["${RESP:0:1}" = "?"]?hangit) exten => s,n,GotoIf($["${RESP:0:1}" = ""]?hangit) exten => s,n,GotoIf($["${RESP:0:5}" != "OHYES"]?hangit) exten => s,n,Set(CALLSIGN=${RESP:5}) exten => s,n,Wait(3) exten => s,n,Playback(rpt/node|noanswer) exten => s,n,Saydigits(${NODENUM}) exten => s,n,Set(CALLERID(num)=0) exten => s,n,Set(CALLERID(name)=${CALLSIGN}) exten => s,n,Rpt(${NODENUM}|X) exten => s,n,Hangup exten => s,n(hangit),Answer exten => s,n(hangit),Wait(1) exten => s,n(hangit),Hangup exten => 9999,1,Goto(allstar-public|s|1) USBRADIO_TUNE_USB29922.CONF [usb29922] ; name=usb29922 ; devicenum=1 devstr=2-1.1 rxmixerset=500 txmixaset=300 txmixbset=500 rxvoiceadj=0.500000 rxctcssadj=0.500000 txctcssadj=200 rxsquelchadj=799 Please feel free to contact me (William) at any time on my cell @ 832-FIVE 4 4-9810