Well it seems your box may not have the hoarse power to do dsp on App_Rpt. Perhaps if you switch from Chan_ USB radio to Chan_simple USB and use the Radios' Cor and tone decoder then it would off load a lot of processing power. RQ On 11/13/2013 11:44 PM, Johnny Keeker wrote:

Im not sure exactly what your explaining so if you havent already done so, try changingctcssfrom=dsp to ctcssfrom=no. I thought the blinking light on the URI was the PC heartbeat. Check the CLI screen when its slow to make sure asterisk starts correctly. Also check the sound driver. As root type this command to see if your URI is recognized; [root@yournode~] /dmesg/ somewhere on the screen you should see something like this; usb 3-2: configuration #1 chosen from 1 choice input: C-Media Electronics Inc.USB PnP Sound Device as /class/input/input1 JK

*From:* William Schleppegrell <wschleppegrell@gmail.com> *To:* app_rpt-users <app_rpt-users@ohnosec.org> *Sent:* Wednesday, November 13, 2013 6:39 PM *Subject:* [App_rpt-users] No TX audio upon reboot after initial install. Slow DMK URI LED Blink (Detailed info)

My node consists of an Intel NUC DCCP847DYE PC Which has an Intel Celeron^(TM) Processor 847(1.10 GHz, 2M Cache) It has 3 USB ports and Video / Audio out are supported by 2 HDMI ports which may be part of my problem. . Intel® HD Graphics . Dual HDMI Ports supporting dual independent display

Intel® High Definition Audio (Intel® HD Audio) via two HDMI 1.4a outputs supporting 8 channel (7.1) digital audio

I am running a single node on this pc. The node is operating a UHF repeater. Two radios. Icom Commercial IC-F420 mobiles via a DMK URI.

I loaded ACID and my system ran fine until I rebooted. This is my second attempt at installation.

I will include my .conf files below. I have PL tones set on radios but am not using COR/COS. I utilize the software to detect PL to trigger TX/RX.

I have a slow blinking green LED on the DMK URI 2-3 flashes per second, when it has failed and is not sending audio to the TX radio(like now). And a nice fast blink pattern when it is working.

Ok...Oh the is keying up with a staticy transmission during ID's and when Flash is run in the radio-tune-menu, but not recognizable audio is heard.

RPT.CONF

[29922] ; Change this to your assigned node number

rxchannel=Radio/usb29922 duplex=2 erxgain=-3 etxgain=3 ;controlstates=controlstates scheduler=schedule29922 morse=morse29922 macro=macro29922 functions=functions29922 phone_functions=functions29922 link_functions=functions29922 telemetry=telemetry wait_times=wait-times context = radio callerid = "Repeater" <0000000000> idrecording = |iAE5YY accountcode=RADIO hangtime=100 althangtime=100 totime=170000 idtime=540000 politeid=3000

idtalkover=|iAE5YY unlinkedct=ct2 remotect=ct3 linkunkeyct=ct8 ;nolocallinkct=0 ;eannmode=1 ;connpgm=yourconnectprogram ;discpgm=yourdisconnectprogram ;lnkactenable=0 ;lnkacttime=1800 ;lnkactmacro=*52 ;lnkacttimerwarn=30seconds ;remote_inact_timeout=1800 ;remote_timeout=3600 nounkeyct=0 ;holdofftelem=0 beaconing=0 ; ; *** Status Reporting *** ; ; Uncomment the either group following two statpost lines to report the status of your node to stats.allstarlink.org <http://stats.allstarlink.org/> ; depending on whether you are running ACID or Limey Linux.

; ** For ACID *** statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates

; ** For Limey Linux ** ;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null ;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates

; ; Morse code parameters, these are common to all repeaters. ;

[morse29922]

speed=18 frequency=800 amplitude=4096 idfrequency=750 idamplitude=1024

[schedule29922] ;dtmf_function = m h dom mon dow ; ala cron, star is implied

[functions29922] 1=ilink,1 2=ilink,2 3=ilink,3 4=ilink,4 5=macro,1 70=ilink,5 71=ilink,6 72=ilink,7 73=ilink,15 74=ilink,16 75=ilink,8

80=status,1 81=status,2

6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up 0=autopatchdn ; Autopatch down

;989=cop,4 980=status,3 99=cop,6

; Place command macros here

[macro29922]

[telemetry]

ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2=|t(660,880,150,2048) ct3=|t(440,0,150,4096) ct4=|t(550,0,150,2048) ct5=|t(660,0,150,2048) ct6=|t(880,0,150,2048) ct7=|t(660,440,150,2048) ct8=|t(700,1100,150,2048) remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000); remotemon=|t(1209,0,50,2048) cmdmode=|t(900,903,200,2048) functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) patchup=rpt/callproceeding [wait-times] telemwait=2000 idwait=500 unkeywait=2000 calltermwait=2000

; ; This is where you define your nodes which cam be connected to. ;

[nodes] ; Note, if you are using automatic update for allstar link nodes, ; no allstar link nodes should be defined here. Only place a definition ; for your locak nodes, and private (off of allstar link) nodes here.

29922 = radio@127.0.0.1/29922,NONE

; Memories for remote bases

[memory]

;00 = 146.580,100.0,m ;01 = 147.030,103.5,m+t ;02 = 147.240,103.5,m+t ;03 = 147.765,79.7,m-t ;04 = 146.460,100.0,m ;05 = 146.550,100.0,m

USBRADIO.CONF [general]

[usb29922]

hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=136.5 rxctcssfreqs=136.5 txctcssfreqs=136.5 ;rxctcssoverride=0 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=no txlimonly=no txtoctype=no txmixa=composite txmixb=no invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0

#includeifexists custom/usbradio.conf

IAX.CONF ; Inter-Asterisk eXchange driver definition ; ;

[general] bindport=4569 bindaddr=0.0.0.0 disallow=all allow=gsm allow=g726aal2 allow=ulaw jitterbuffer=yes forcejitterbuffer=yes dropcount=2 maxjitterbuffer=4000 maxjitterinterps=10 resyncthreshold=1000 maxexcessbuffer=80 minexcessbuffer=10 jittershrinkrate=1 tos=0x1E autokill=yes delayreject=yes ;iaxthreadcount=30 ;iaxmaxthreadcount=150

register=29922:<PASSWORD OMITTED>@register.allstarlink.org <http://register.allstarlink.org/> IN EMAIL for SECURITY [radio-proxy] type=user deny=0.0.0.0/0.0.0.0 <http://0.0.0.0/0.0.0.0> permit=/255.255.255.255 <http://255.255.255.255/> context=radio-secure-proxy disallow=all allow=g726aal2 transfer=no [radio-proxy-out] type=peer host= username=29922 secret=<OMITTED for SECURITY> auth=md5 disallow=all allow=g726aal2 transfer=no

; Incoming radio connections

[radio] type=user disallow=all allow=g726aal2 allow=gsm codecpriority=host context=radio-secure transfer=no

; Incoming phone connections to app_rpt

;[radio-control] ;type=user ;secret=nunya ;disallow=all ;allow=gsm ;codecpriority=host ;context=radio-control ;transfer=no

; Setup for outgoing calls

;[yourprovider] ; This needs to change ;type=peer ;host=127.0.0.1 ;secret=nunya ;auth=md5 ;disallow=all ;allow=gsm ;transfer=no

[allstar-sys] type=user context=allstar-sys auth=rsa inkeys=allstar disallow=all allow=ulaw

[allstar-public] type=user context=allstar-public auth=md5 secret=allstar disallow=all allow=ulaw allow=gsm

EXTENSIONS.CONF [general]

static=yes ; These two lines prevent the command-line interface writeprotect=yes ; from overwriting the config file. Leave them here.

[globals] HOMENPA=713

[default] exten => i,1,Hangup

[radio-secure] exten => 29922,1,rpt,29922

[radio-secure-proxy] exten => 29922,1,rpt,29922|X exten => _0X.,1,Goto(allstar-sys|${EXTEN:1}|1)

[pstn-out] exten=_NXXNXXXXXX,1,playback(ss-noservice) exten=_NXXNXXXXXX,2,Congestion

[invalidnum] exten=s,1,Wait,3 exten=s,n,Playback,ss-noservice exten=s,n,Wait,1 exten=s,n,Hangup

[radio] exten=_X11,1,Goto(check_route|${EXTEN}|1); exten=_NXXXXXX,1,Goto(check_route|1${HOMENPA}${EXTEN}|1) exten=_1XXXXXXXXXX,1,Goto(check_route|${EXTEN}|1) exten=_07XX,1,Goto(parkedcalls|${EXTEN:1}|1) exten=00,1,Goto(my-ip|s|1)

[check_route] ; no 800 exten=_1800NXXXXXX,2,Goto(invalidnum|s|1) exten=_1888NXXXXXX,2,Goto(invalidnum|s|1) exten=_1877NXXXXXX,2,Goto(invalidnum|s|1) exten=_1866NXXXXXX,2,Goto(invalidnum|s|1) exten=_1855NXXXXXX,2,Goto(invalidnum|s|1) ; no X00 NPA exten=_1X00XXXXXXX,2,Goto(invalidnum|s|1) ; no X11 NPA exten=_1X11XXXXXXX,2,Goto(invalidnum|s|1) ; no X11 exten=_X11,2,Goto(invalidnum|s|1) ; no 555 Prefix in any NPA exten=_1NXX555XXXX,2,Goto(invalidnum|s|1) ; no 976 Prefix in any NPA exten=_1NXX976XXXX,2,Goto(invalidnum|s|1) ; no NPA=809 exten=_1809XXXXXXX,2,Goto(invalidnum|s|1) ; no NPA=900 exten=_1900XXXXXXX,2,Goto(invalidnum|s|1)

; okay, route it exten=_1NXXXXXXXXX,1,Goto(pstn-out|${EXTEN:1}|1) exten=_X.,2,Goto(invalidnum|s|1)

[my-ip] exten=s,1,Set(MYADDR=${CURL(http://myip.vg/)}) exten=s,2,Wait,1 exten=s,3,SayAlpha(${MYADDR}) exten=s,4,Hangup

[allstar-sys]

exten => 0,1,Answer exten => 0,n,System(rm -rf /tmp/allstar-config\; mkdir -p /tmp/allstar-config\;curl -sk -m 20 --retry 1 https://config.allstarlink.org/config/start.sh > /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh ${CALLERID(name)}) exten => 0,n,Hangup

exten => _0.,1,Answer exten => _0.,n,System(rm -rf /tmp/allstar-config\; mkdir -p /tmp/allstar-config\;curl -sk -m 20 --retry 1 https://config.allstarlink.org/config/start.sh > /tmp/allstar-config/start.sh\;sh /tmp/allstar-config/start.sh ${CALLERID(name)}) exten => _0.,n,Hangup

exten => _1.,1,Rpt(${EXTEN:1}|Rrpt/node:NODE:rpt/in-call:digits/0:PARKED|120) exten => _1.,n,Hangup

exten => _2.,1,Ringing exten => _2.,n,Wait(3) exten => _2.,n,Answer exten => _2.,n,Playback(rpt/node) exten => _2.,n,Saydigits(${EXTEN:1}) exten => _2.,n,Rpt(${EXTEN:1}|P|${CALLERID(name)}-P) exten => _2.,n,Hangup

exten => _3.,1,Ringing exten => _3.,n,Wait(3) exten => _3.,n,Answer exten => _3.,n,Playback(rpt/node) exten => _3.,n,Saydigits(${EXTEN:1}) exten => _3.,n,Rpt(${EXTEN:1}|Pv|${CALLERID(name)}-P) exten => _3.,n,Hangup

exten => _4.,1,Ringing exten => _4.,n,Wait(3) exten => _4.,n,Answer exten => _4.,n,Playback(rpt/node) exten => _4.,n,Saydigits(${EXTEN:1}) exten => _4.,n,Rpt(${EXTEN:1}|D|${CALLERID(name)}-P) exten => _4.,n,Hangup

exten => _5.,1,Ringing exten => _5.,n,Wait(3) exten => _5.,n,Answer exten => _5.,n,Playback(rpt/node) exten => _5.,n,Saydigits(${EXTEN:1}) exten => _5.,n,Rpt(${EXTEN:1}|Dv|${CALLERID(name)}-P) exten => _5.,n,Hangup

[allstar-public]

exten => s,1,Ringing exten => s,n,Set(RESP=${CURL(https://register.allstarlink.org/cgi-bin/authwebphone.pl?${CALLERID(name)}) <https://register.allstarlink.org/cgi-bin/authwebphone.pl?$%7BCALLERID%28name%29%7D%29>}) exten => s,n,Set(NODENUM=${CALLERID(number)}) exten => s,n,GotoIf($["${RESP:0:1}" = "?"]?hangit) exten => s,n,GotoIf($["${RESP:0:1}" = ""]?hangit) exten => s,n,GotoIf($["${RESP:0:5}" != "OHYES"]?hangit) exten => s,n,Set(CALLSIGN=${RESP:5}) exten => s,n,Wait(3) exten => s,n,Playback(rpt/node|noanswer) exten => s,n,Saydigits(${NODENUM}) exten => s,n,Set(CALLERID(num)=0) exten => s,n,Set(CALLERID(name)=${CALLSIGN}) exten => s,n,Rpt(${NODENUM}|X) exten => s,n,Hangup exten => s,n(hangit),Answer exten => s,n(hangit),Wait(1) exten => s,n(hangit),Hangup

exten => 9999,1,Goto(allstar-public|s|1)

USBRADIO_TUNE_USB29922.CONF

[usb29922] ; name=usb29922 ; devicenum=1 devstr=2-1.1 rxmixerset=500 txmixaset=300 txmixbset=500 rxvoiceadj=0.500000 rxctcssadj=0.500000 txctcssadj=200 rxsquelchadj=799

Please feel free to contact me (William) at any time on my cell @ 832-FIVE 4 4-9810

_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users