I can't really tell the facts based on what you have stated but, I'll give you a place to look anyway. I'm guessing (perhaps incorrectly) you are interfacing this with a transceiver for link , you may be in the wrong mode for a transceiver type link. and/or full/half duplex issues. OR Try inverting the logic of your COR/COS and/or PTT line from the TRX. But invert it electronically first. Perhaps with a 3904/3906 transistor. Then adjust the software logic as needed. It sounds like your audio is not gateing with the COR/PTT. A place to start ? But it always helps others helping you if you state the software you are using (acid,dial, etc) and/or the the hardware (PC,BBB, Pi etc) and your node connection configuration (simplex/duplex repeater, TRX link etc) It helps everyone get a mental picture for what you are doing. and how you are trying to do it and gets the attention of those doing like things. Just a suggestion. ...mike/kb8jnm
Update: I made some changes in the simpleusb.conf file and was able to get the keying problem solved. Still no audio being transmitted from the receiver. I hear myself talking in the monitor and with headphones on pin 21 but still transmitter keys but no audio. Chris Viningre 70 W. Roadrunner Salt Flat, Texas 79847 C:(915) 504-1510 chrisviningre@gmail.com Amateur Radio Operator: WS5B https://www.qrz.com/db/ws5b http://www.reverbnation.com/chrisviningre
On Mon, Sep 19, 2016 at 6:40 PM, Chris Viningre <chrisviningre@gmail.com> wrote:
Greetings from a ham radio dummy. I'm old to ham radio but new to setting up repeaters, Allstar and URI. Also lost working with Linux. Yes pretty much a disaster looking for a place to happen. I have a repeater running with a RC-100 controller on VHF. I'm attempting to add a link to a linked system over Allstar. I have removed the old controller and wired the URI. To the best of my knowledge I have the wiring correct, but I could be wrong. I downloaded the Linux software from the Allstarlink website and made a bootable disk. I loaded the Debian with Asterisk software only, Not the Graphical version. At the end of the install I manually added my information. I put my node number and password number in. I followed the support information from the Allstar site and did a node download from Allstar. I checked for my node on the Allstar list and it is listed. I called the link phone number and I can get through the login but it doesn't seem to connect to my link. I get a busy signal and it hangs up. When I key a HT the repeater sometimes comes up. Most of the time I have the key the PTT 2 or 3 times in a row to make it key up. Either way I get no audio out of the transmitter other then the IDer and beep. I hear the receiver just fine. I have search for help all over the internet, but what information I find is like a Texan trying to read Arabic. I speak Texagain so I'm not really the best with the English language. At lease according to my wife. Well I'm hoping maybe someone can help me get this working or lead me in some kind of direction. Thank you.
Chris Viningre 70 W. Roadrunner Salt Flat, Texas 79847 C:(915) 504-1510 chrisviningre@gmail.com Amateur Radio Operator: WS5B https://www.qrz.com/db/ws5b http://www.reverbnation.com/chrisviningre
App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.