IT WORKS NOW I tried the next pc (an older one) and it works fine without any config changes. It`s short before midnight and I must go to work tomorrow ☹ I will look the next days which CPUs and Chipsets I tried and doesn`t work and which one work now ok ? Good n8 tom dh6mbt Von: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] Im Auftrag von kk6ecm Gesendet: Dienstag, 3. Juni 2014 23:13 An: App_rpt-users@ohnosec.org Betreff: Re: [App_rpt-users] no audio from URI Try amplifying the output of the URI in order to drive the speaker. If that does not work, I'd test the URI using a loopback connector and uridiag down loaded from http://www.dmkeng.com/images/URI-FAQs.pdf Make sure Asterisk is stopped when uridiag is used. Service asterisk stop on the Linux command line. This is not a test to determine URI health, but the ability of the ACID build on your computer, and the ability to send audio to the URI. Thanks, Bob kk6ecm Sent from iPad On Jun 3, 2014, at 2:51 PM, "torben@klimt-online.com<mailto:torben@klimt-online.com>" <torben@klimt-online.com<mailto:torben@klimt-online.com>> wrote: Now i tried 3 different computers with 2 URI-Boards and 3 installs - SQL detect by DSP -> ok - DTMF reading -> ok - Transmitting by PTT -> ok - Sending audio -> NO I have headphones connectet direct to the URI on Pins 13 (GND) and 22/23 -> no nothing ☹ ☹ Von: app_rpt-users-bounces@ohnosec.org<mailto:app_rpt-users-bounces@ohnosec.org> [mailto:app_rpt-users-bounces@ohnosec.org] Im Auftrag von kk6ecm Gesendet: Dienstag, 3. Juni 2014 14:11 An: App_rpt-users@ohnosec.org<mailto:App_rpt-users@ohnosec.org> Betreff: Re: [App_rpt-users] no audio from URI Again, I'm not sure if it is your issue, but the chipset used in your board is of the same family as the one I seemed to have difficulty. When I chose a board with an older generation chipset (NM10, and not the 7x series), the audio worked good. Thanks, Bob kk6ecm Sent from iPad On Jun 3, 2014, at 4:19 AM, "torben@klimt-online.com<mailto:torben@klimt-online.com>" <torben@klimt-online.com<mailto:torben@klimt-online.com>> wrote: i take this box http://www.intel.com/content/dam/www/public/us/en/documents/product-briefs/d... 73 de tom dh6mbt ________________________________ Von: app_rpt-users-bounces@ohnosec.org<mailto:app_rpt-users-bounces@ohnosec.org> [app_rpt-users-bounces@ohnosec.org<mailto:app_rpt-users-bounces@ohnosec.org>] im Auftrag von kk6ecm [kk6ecm@gmail.com<mailto:kk6ecm@gmail.com>] Gesendet: Dienstag, 3. Juni 2014 12:59 An: App_rpt-users@ohnosec.org<mailto:App_rpt-users@ohnosec.org> Betreff: Re: [App_rpt-users] no audio from URI I'm not sure of your issue, but your experience sounds like mine when I attempted to use a computer with a newer chipset, incompatible withe CentOS 5.10. That was Intel chipset NM 70. When I used a mother board with the older Intel chipset NM 10, I hade no audio issues. I discovered the issue when using DMK Engineering uridiag software on the ACID build (see URI FAQ on the DMK website re uridiag and loopback testing). Thanks, Bob kk6ecm Sent from iPad On Jun 2, 2014, at 11:01 PM, "torben@klimt-online.com<mailto:torben@klimt-online.com>" <torben@klimt-online.com<mailto:torben@klimt-online.com>> wrote: good morning, i connect a headphone to the URI so we don`t need to search the problem on the Motorolas.... 73... ________________________________ Von: David Morley [ab8tn1@cox.net<mailto:ab8tn1@cox.net>] Gesendet: Dienstag, 3. Juni 2014 07:14 An: torben@klimt-online.com<mailto:torben@klimt-online.com> Betreff: Re: [App_rpt-users] no audio from URI Are the GM 360s the same as the GM 300s? Do they have 16 pin connectors Sent from my iPhone On Jun 2, 2014, at 2:07 PM, "torben@klimt-online.com<mailto:torben@klimt-online.com>" <torben@klimt-online.com<mailto:torben@klimt-online.com>> wrote: Hi all, i think i have a little blackout ☹ I would like to set up a repeater with 2 GM360 <!--[if !supportLists]-->- <!--[endif]-->SQL detect is ok <!--[if !supportLists]-->- <!--[endif]-->NF to another connectet repeater is ok <!--[if !supportLists]-->- <!--[endif]-->DTMF is ok (looks good on console) <!--[if !supportLists]-->- <!--[endif]-->PTT is ok BUT there is no audio out from the URI on Port 22 and or 23 ☹ On a windows machine the URI works fine but on the asterisk there is no output Any ideas ? greetings _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org<mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org<mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.