Michael: Just to make sure its out there ... the DSP software doesn't decode some standard PL tones. It will generate anything to the TX. If you haven't run this down yet ... I remember seeing a list of PL tones but I can't find it now. I use the method you are trying to use and it works without any problems. ...STeve - KF5VH On 8/9/2017 10:40 AM, Michael "Lee" Lockwood wrote:
Thanks for the reply Steve. When I uncomment txctcssdefault, it reverts to no ctcss on the transmit side when PTT is release.
On Wed, Aug 9, 2017 at 10:30 AM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Michael, We are looking at the channel drives now. I can't say I have tried your config. I will test when I get a chance. Your configuration looks correct. I would be interested in hearing what happens when you comment out the txctcssdefault. Hopefully someone else will chime in.
73, Steve N4IRS
On 8/9/2017 11:12 AM, Michael "Lee" Lockwood wrote:
A follow up to my previous email:
I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead.
So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail.
Has anyone else run in to this issue?
Here's my usbradio.conf file again:
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood <michael@lockwood.us.com <mailto:michael@lockwood.us.com>> wrote:
Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance!
Here's what's in my usbradio.conf
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
--
*Michael "Lee" Lockwood* michael@lockwood.us.com <mailto:michael@lockwood.us.com>
--
*Michael "Lee" Lockwood* michael@lockwood.us.com <mailto:michael@lockwood.us.com>
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
To unsubscribe from this list please visithttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
--
*Michael "Lee" Lockwood* michael@lockwood.us.com <mailto:michael@lockwood.us.com>
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. www.avg.com <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
<#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.