Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance! Here's what's in my usbradio.conf [usb] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 -- *Michael "Lee" Lockwood* michael@lockwood.us.com
A follow up to my previous email: I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead. So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail. Has anyone else run in to this issue? Here's my usbradio.conf file again: [usb] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood < michael@lockwood.us.com> wrote:
Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance!
Here's what's in my usbradio.conf
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
-- *Michael "Lee" Lockwood* michael@lockwood.us.com
Michael, We are looking at the channel drives now. I can't say I have tried your config. I will test when I get a chance. Your configuration looks correct. I would be interested in hearing what happens when you comment out the txctcssdefault. Hopefully someone else will chime in. 73, Steve N4IRS On 8/9/2017 11:12 AM, Michael "Lee" Lockwood wrote:
A follow up to my previous email:
I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead.
So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail.
Has anyone else run in to this issue?
Here's my usbradio.conf file again:
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood <michael@lockwood.us.com <mailto:michael@lockwood.us.com>> wrote:
Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance!
Here's what's in my usbradio.conf
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
--
*Michael "Lee" Lockwood* michael@lockwood.us.com <mailto:michael@lockwood.us.com>
--
*Michael "Lee" Lockwood* michael@lockwood.us.com <mailto:michael@lockwood.us.com>
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Thanks for the reply Steve. When I uncomment txctcssdefault, it reverts to no ctcss on the transmit side when PTT is release. On Wed, Aug 9, 2017 at 10:30 AM, Steve Zingman <szingman@msgstor.com> wrote:
Michael, We are looking at the channel drives now. I can't say I have tried your config. I will test when I get a chance. Your configuration looks correct. I would be interested in hearing what happens when you comment out the txctcssdefault. Hopefully someone else will chime in.
73, Steve N4IRS
On 8/9/2017 11:12 AM, Michael "Lee" Lockwood wrote:
A follow up to my previous email:
I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead.
So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail.
Has anyone else run in to this issue?
Here's my usbradio.conf file again:
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood < michael@lockwood.us.com> wrote:
Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance!
Here's what's in my usbradio.conf
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- *Michael "Lee" Lockwood* michael@lockwood.us.com
Michael: Just to make sure its out there ... the DSP software doesn't decode some standard PL tones. It will generate anything to the TX. If you haven't run this down yet ... I remember seeing a list of PL tones but I can't find it now. I use the method you are trying to use and it works without any problems. ...STeve - KF5VH On 8/9/2017 10:40 AM, Michael "Lee" Lockwood wrote:
Thanks for the reply Steve. When I uncomment txctcssdefault, it reverts to no ctcss on the transmit side when PTT is release.
On Wed, Aug 9, 2017 at 10:30 AM, Steve Zingman <szingman@msgstor.com <mailto:szingman@msgstor.com>> wrote:
Michael, We are looking at the channel drives now. I can't say I have tried your config. I will test when I get a chance. Your configuration looks correct. I would be interested in hearing what happens when you comment out the txctcssdefault. Hopefully someone else will chime in.
73, Steve N4IRS
On 8/9/2017 11:12 AM, Michael "Lee" Lockwood wrote:
A follow up to my previous email:
I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead.
So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail.
Has anyone else run in to this issue?
Here's my usbradio.conf file again:
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood <michael@lockwood.us.com <mailto:michael@lockwood.us.com>> wrote:
Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance!
Here's what's in my usbradio.conf
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
--
*Michael "Lee" Lockwood* michael@lockwood.us.com <mailto:michael@lockwood.us.com>
--
*Michael "Lee" Lockwood* michael@lockwood.us.com <mailto:michael@lockwood.us.com>
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
To unsubscribe from this list please visithttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
--
*Michael "Lee" Lockwood* michael@lockwood.us.com <mailto:michael@lockwood.us.com>
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. www.avg.com <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
<#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
if the default tone could be set to last then the the tx tone would always be the last heard but I am not sure that’s what you want Thanks 73 Neil Sablatzky K8IT Allstar Node 41838 KITLINK Allstar Node 42087 KITLINK HUB IRLP Node exp0068 Echolink K8IT-L WIRES-X K8IT 11479 Room 21479 From: Michael "Lee" Lockwood Sent: Wednesday, August 09, 2017 11:40 AM To: Users of Asterisk app_rpt Subject: Re: [App_rpt-users] ctcss Encode Issues Thanks for the reply Steve. When I uncomment txctcssdefault, it reverts to no ctcss on the transmit side when PTT is release. On Wed, Aug 9, 2017 at 10:30 AM, Steve Zingman <szingman@msgstor.com> wrote: Michael, We are looking at the channel drives now. I can't say I have tried your config. I will test when I get a chance. Your configuration looks correct. I would be interested in hearing what happens when you comment out the txctcssdefault. Hopefully someone else will chime in. 73, Steve N4IRS On 8/9/2017 11:12 AM, Michael "Lee" Lockwood wrote: A follow up to my previous email: I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead. So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail. Has anyone else run in to this issue? Here's my usbradio.conf file again: [usb] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood <michael@lockwood.us.com> wrote: Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance! Here's what's in my usbradio.conf [usb] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 -- Michael "Lee" Lockwood michael@lockwood.us.com -- Michael "Lee" Lockwood michael@lockwood.us.com _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. -- Michael "Lee" Lockwood michael@lockwood.us.com -------------------------------------------------------------------------------- _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Neil: When you say "default tone set to last", I'm not sure where/what you're referring to. I have the 151.4 (default tone) as the last entry in rxtctcssfreqs= and txctcssfreqs= in usbradio.conf already. Is that what you're referring to? On Wed, Aug 9, 2017 at 11:27 AM, Neil k8it <k8it@cac.net> wrote:
if the default tone could be set to last then the the tx tone would always be the last heard but I am not sure that’s what you want
Thanks 73 Neil Sablatzky K8IT Allstar Node 41838 KITLINK Allstar Node 42087 KITLINK HUB IRLP Node exp0068 Echolink K8IT-L WIRES-X K8IT 11479 Room 21479
*From:* Michael "Lee" Lockwood <michael@lockwood.us.com> *Sent:* Wednesday, August 09, 2017 11:40 AM *To:* Users of Asterisk app_rpt <app_rpt-users@lists.allstarlink.org> *Subject:* Re: [App_rpt-users] ctcss Encode Issues
Thanks for the reply Steve. When I uncomment txctcssdefault, it reverts to no ctcss on the transmit side when PTT is release.
On Wed, Aug 9, 2017 at 10:30 AM, Steve Zingman <szingman@msgstor.com> wrote:
Michael, We are looking at the channel drives now. I can't say I have tried your config. I will test when I get a chance. Your configuration looks correct. I would be interested in hearing what happens when you comment out the txctcssdefault. Hopefully someone else will chime in.
73, Steve N4IRS
On 8/9/2017 11:12 AM, Michael "Lee" Lockwood wrote:
A follow up to my previous email:
I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead.
So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail.
Has anyone else run in to this issue?
Here's my usbradio.conf file again:
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood < michael@lockwood.us.com> wrote:
Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance!
Here's what's in my usbradio.conf
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/c gi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
------------------------------
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- *Michael "Lee" Lockwood* michael@lockwood.us.com
if the parameter last could be added to the source code Thanks 73 Neil Sablatzky K8IT Allstar Node 41838 KITLINK Allstar Node 42087 KITLINK HUB IRLP Node exp0068 Echolink K8IT-L WIRES-X K8IT 11479 Room 21479 From: Michael "Lee" Lockwood Sent: Wednesday, August 09, 2017 12:43 PM To: Users of Asterisk app_rpt Subject: Re: [App_rpt-users] ctcss Encode Issues Neil: When you say "default tone set to last", I'm not sure where/what you're referring to. I have the 151.4 (default tone) as the last entry in rxtctcssfreqs= and txctcssfreqs= in usbradio.conf already. Is that what you're referring to? On Wed, Aug 9, 2017 at 11:27 AM, Neil k8it <k8it@cac.net> wrote: if the default tone could be set to last then the the tx tone would always be the last heard but I am not sure that’s what you want Thanks 73 Neil Sablatzky K8IT Allstar Node 41838 KITLINK Allstar Node 42087 KITLINK HUB IRLP Node exp0068 Echolink K8IT-L WIRES-X K8IT 11479 Room 21479 From: Michael "Lee" Lockwood Sent: Wednesday, August 09, 2017 11:40 AM To: Users of Asterisk app_rpt Subject: Re: [App_rpt-users] ctcss Encode Issues Thanks for the reply Steve. When I uncomment txctcssdefault, it reverts to no ctcss on the transmit side when PTT is release. On Wed, Aug 9, 2017 at 10:30 AM, Steve Zingman <szingman@msgstor.com> wrote: Michael, We are looking at the channel drives now. I can't say I have tried your config. I will test when I get a chance. Your configuration looks correct. I would be interested in hearing what happens when you comment out the txctcssdefault. Hopefully someone else will chime in. 73, Steve N4IRS On 8/9/2017 11:12 AM, Michael "Lee" Lockwood wrote: A follow up to my previous email: I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead. So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail. Has anyone else run in to this issue? Here's my usbradio.conf file again: [usb] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood <michael@lockwood.us.com> wrote: Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance! Here's what's in my usbradio.conf [usb] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 -- Michael "Lee" Lockwood michael@lockwood.us.com -- Michael "Lee" Lockwood michael@lockwood.us.com _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. -- Michael "Lee" Lockwood michael@lockwood.us.com ------------------------------------------------------------------------------ _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. -- Michael "Lee" Lockwood michael@lockwood.us.com -------------------------------------------------------------------------------- _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
for how long after a giben ctcss tone is reciebed do you want to use the same ctcss tx tone when would it reset to the 151.4 tone Thanks 73 Neil Sablatzky K8IT Allstar Node 41838 KITLINK Allstar Node 42087 KITLINK HUB IRLP Node exp0068 Echolink K8IT-L WIRES-X K8IT 11479 Room 21479 From: Michael "Lee" Lockwood Sent: Wednesday, August 09, 2017 11:12 AM To: app_rpt-users@lists.allstarlink.org Subject: Re: [App_rpt-users] ctcss Encode Issues A follow up to my previous email: I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead. So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail. Has anyone else run in to this issue? Here's my usbradio.conf file again: [usb] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood <michael@lockwood.us.com> wrote: Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance! Here's what's in my usbradio.conf [usb] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 -- Michael "Lee" Lockwood michael@lockwood.us.com -- Michael "Lee" Lockwood michael@lockwood.us.com -------------------------------------------------------------------------------- _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Steve Mahler: The RX ctcss tones I'm using are being decoded by the dsp. I get verification of that when running debug in app_rpt. Neil: I'd like to have the same ctcss tone transmitted for the "repeater tail" and courtesy tone the same amount of time it's set in the rpt.conf file. I think I have mine set to 1.5 seconds. On Wed, Aug 9, 2017 at 11:01 AM, Neil k8it <k8it@cac.net> wrote:
for how long after a giben ctcss tone is reciebed do you want to use the same ctcss tx tone when would it reset to the 151.4 tone Thanks 73 Neil Sablatzky K8IT Allstar Node 41838 KITLINK Allstar Node 42087 KITLINK HUB IRLP Node exp0068 Echolink K8IT-L WIRES-X K8IT 11479 Room 21479
*From:* Michael "Lee" Lockwood <michael@lockwood.us.com> *Sent:* Wednesday, August 09, 2017 11:12 AM *To:* app_rpt-users@lists.allstarlink.org *Subject:* Re: [App_rpt-users] ctcss Encode Issues
A follow up to my previous email:
I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead.
So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail.
Has anyone else run in to this issue?
Here's my usbradio.conf file again:
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood < michael@lockwood.us.com> wrote:
Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance!
Here's what's in my usbradio.conf
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
------------------------------
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- *Michael "Lee" Lockwood* michael@lockwood.us.com
Neil: Understood. As long as you are thinking about a code change ... should the PL tone be held thru the tailmessage system too? ...STeve On 8/9/2017 11:15 AM, Michael "Lee" Lockwood wrote:
Steve Mahler: The RX ctcss tones I'm using are being decoded by the dsp. I get verification of that when running debug in app_rpt.
Neil: I'd like to have the same ctcss tone transmitted for the "repeater tail" and courtesy tone the same amount of time it's set in the rpt.conf file. I think I have mine set to 1.5 seconds.
On Wed, Aug 9, 2017 at 11:01 AM, Neil k8it <k8it@cac.net <mailto:k8it@cac.net>> wrote:
for how long after a giben ctcss tone is reciebed do you want to use the same ctcss tx tone when would it reset to the 151.4 tone Thanks 73 Neil Sablatzky K8IT Allstar Node 41838 KITLINK Allstar Node 42087 KITLINK HUB IRLP Node exp0068 Echolink K8IT-L WIRES-X K8IT 11479 Room 21479
*From:* Michael "Lee" Lockwood <mailto:michael@lockwood.us.com> *Sent:* Wednesday, August 09, 2017 11:12 AM *To:* app_rpt-users@lists.allstarlink.org <mailto:app_rpt-users@lists.allstarlink.org> *Subject:* Re: [App_rpt-users] ctcss Encode Issues
A follow up to my previous email:
I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead.
So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail.
Has anyone else run in to this issue?
Here's my usbradio.conf file again:
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood <michael@lockwood.us.com <mailto:michael@lockwood.us.com>> wrote:
Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance!
Here's what's in my usbradio.conf
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
--
*Michael "Lee" Lockwood* michael@lockwood.us.com <mailto:michael@lockwood.us.com>
--
*Michael "Lee" Lockwood* michael@lockwood.us.com <mailto:michael@lockwood.us.com>
------------------------------------------------------------------------ _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
--
*Michael "Lee" Lockwood* michael@lockwood.us.com <mailto:michael@lockwood.us.com>
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. www.avg.com <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient>
<#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
that could be a option, configurable Thanks 73 Neil Sablatzky K8IT Allstar Node 41838 KITLINK Allstar Node 42087 KITLINK HUB IRLP Node exp0068 Echolink K8IT-L WIRES-X K8IT 11479 Room 21479 From: Steve Mahler Sent: Wednesday, August 09, 2017 12:21 PM To: app_rpt-users@lists.allstarlink.org Subject: Re: [App_rpt-users] ctcss Encode Issues Neil: Understood. As long as you are thinking about a code change ... should the PL tone be held thru the tailmessage system too? ...STeve On 8/9/2017 11:15 AM, Michael "Lee" Lockwood wrote: Steve Mahler: The RX ctcss tones I'm using are being decoded by the dsp. I get verification of that when running debug in app_rpt. Neil: I'd like to have the same ctcss tone transmitted for the "repeater tail" and courtesy tone the same amount of time it's set in the rpt.conf file. I think I have mine set to 1.5 seconds. On Wed, Aug 9, 2017 at 11:01 AM, Neil k8it <k8it@cac.net> wrote: for how long after a giben ctcss tone is reciebed do you want to use the same ctcss tx tone when would it reset to the 151.4 tone Thanks 73 Neil Sablatzky K8IT Allstar Node 41838 KITLINK Allstar Node 42087 KITLINK HUB IRLP Node exp0068 Echolink K8IT-L WIRES-X K8IT 11479 Room 21479 From: Michael "Lee" Lockwood Sent: Wednesday, August 09, 2017 11:12 AM To: app_rpt-users@lists.allstarlink.org Subject: Re: [App_rpt-users] ctcss Encode Issues A follow up to my previous email: I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead. So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail. Has anyone else run in to this issue? Here's my usbradio.conf file again: [usb] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood <michael@lockwood.us.com> wrote: Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance! Here's what's in my usbradio.conf [usb] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 -- Michael "Lee" Lockwood michael@lockwood.us.com -- Michael "Lee" Lockwood michael@lockwood.us.com ---------------------------------------------------------------------------- _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. -- Michael "Lee" Lockwood michael@lockwood.us.com Virus-free. www.avg.com _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. -------------------------------------------------------------------------------- _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Just to circle back on this topic... I tried itxctcss = as both 1 and 0 and no difference on this. If I'm understanding correctly, at this point app_rpt does only transmit the "default" ctcss for the repeater tail and courtesy tone, by design. It does not transmit the other txctcss tones in the usbradio.conf file. I haven't misconfigured anything? On Wed, Aug 9, 2017 at 12:01 PM, Neil k8it <k8it@cac.net> wrote:
that could be a option, configurable
Thanks 73 Neil Sablatzky K8IT Allstar Node 41838 KITLINK Allstar Node 42087 KITLINK HUB IRLP Node exp0068 Echolink K8IT-L WIRES-X K8IT 11479 Room 21479
*From:* Steve Mahler <kizzy@lusfiber.net> *Sent:* Wednesday, August 09, 2017 12:21 PM *To:* app_rpt-users@lists.allstarlink.org *Subject:* Re: [App_rpt-users] ctcss Encode Issues
Neil:
Understood. As long as you are thinking about a code change ... should the PL tone be held thru the tailmessage system too?
...STeve
On 8/9/2017 11:15 AM, Michael "Lee" Lockwood wrote:
Steve Mahler: The RX ctcss tones I'm using are being decoded by the dsp. I get verification of that when running debug in app_rpt.
Neil: I'd like to have the same ctcss tone transmitted for the "repeater tail" and courtesy tone the same amount of time it's set in the rpt.conf file. I think I have mine set to 1.5 seconds.
On Wed, Aug 9, 2017 at 11:01 AM, Neil k8it <k8it@cac.net> wrote:
for how long after a giben ctcss tone is reciebed do you want to use the same ctcss tx tone when would it reset to the 151.4 tone Thanks 73 Neil Sablatzky K8IT Allstar Node 41838 KITLINK Allstar Node 42087 KITLINK HUB IRLP Node exp0068 Echolink K8IT-L WIRES-X K8IT 11479 Room 21479
*From:* Michael "Lee" Lockwood <michael@lockwood.us.com> *Sent:* Wednesday, August 09, 2017 11:12 AM *To:* app_rpt-users@lists.allstarlink.org *Subject:* Re: [App_rpt-users] ctcss Encode Issues
A follow up to my previous email:
I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead.
So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail.
Has anyone else run in to this issue?
Here's my usbradio.conf file again:
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood < michael@lockwood.us.com> wrote:
Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance!
Here's what's in my usbradio.conf
[usb]
hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
------------------------------ _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/c gi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/c gi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
<http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> Virus-free. www.avg.com <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> <#m_1887823366555273984_DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
------------------------------
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- *Michael "Lee" Lockwood* michael@lockwood.us.com
On Fri, Aug 11, 2017 at 8:28 AM, Michael "Lee" Lockwood <michael@lockwood.us.com> wrote:
Just to circle back on this topic...
I tried itxctcss = as both 1 and 0 and no difference on this.
If I'm understanding correctly, at this point app_rpt does only transmit the "default" ctcss for the repeater tail and courtesy tone, by design. It does not transmit the other txctcss tones in the usbradio.conf file. I haven't misconfigured anything?
If I were designing it, I would have done it this way, so I think that yes it is acting as designed. However, since the itxctcss command exists, it should follow the itxctcss command. It sounds like that piece was never implemented. This is sort of halfway between a feature request and a bug report, but I think it should be programmed so that when itxctcss == 1 it operates as it does now, and when itxctcss == 0 it should operate as you request, transmitting the input tone through the end of the transmission. Tom KD7LXL
Understood, thanks Tom! I hope this does get implemented, or finalized at some point. On Fri, Aug 11, 2017 at 10:36 AM, Tom Hayward <tom@tomh.us> wrote:
On Fri, Aug 11, 2017 at 8:28 AM, Michael "Lee" Lockwood <michael@lockwood.us.com> wrote:
Just to circle back on this topic...
I tried itxctcss = as both 1 and 0 and no difference on this.
If I'm understanding correctly, at this point app_rpt does only transmit
the "default" ctcss for the repeater tail and courtesy tone, by design. It does not transmit the other txctcss tones in the usbradio.conf file. I haven't misconfigured anything?
If I were designing it, I would have done it this way, so I think that yes it is acting as designed.
However, since the itxctcss command exists, it should follow the itxctcss command. It sounds like that piece was never implemented. This is sort of halfway between a feature request and a bug report, but I think it should be programmed so that when itxctcss == 1 it operates as it does now, and when itxctcss == 0 it should operate as you request, transmitting the input tone through the end of the transmission.
Tom KD7LXL _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- *Michael "Lee" Lockwood* michael@lockwood.us.com
It will be looked at. Work is happening on channel drivers now. (among a LOT of other things) Steve N4IRS On 8/11/2017 11:39 AM, Michael "Lee" Lockwood wrote:
Understood, thanks Tom! I hope this does get implemented, or finalized at some point.
On Fri, Aug 11, 2017 at 10:36 AM, Tom Hayward <tom@tomh.us <mailto:tom@tomh.us>> wrote:
On Fri, Aug 11, 2017 at 8:28 AM, Michael "Lee" Lockwood <michael@lockwood.us.com <mailto:michael@lockwood.us.com>> wrote: > > Just to circle back on this topic... > > I tried itxctcss = as both 1 and 0 and no difference on this. > > If I'm understanding correctly, at this point app_rpt does only transmit the "default" ctcss for the repeater tail and courtesy tone, by design. It does not transmit the other txctcss tones in the usbradio.conf file. I haven't misconfigured anything?
If I were designing it, I would have done it this way, so I think that yes it is acting as designed.
However, since the itxctcss command exists, it should follow the itxctcss command. It sounds like that piece was never implemented. This is sort of halfway between a feature request and a bug report, but I think it should be programmed so that when itxctcss == 1 it operates as it does now, and when itxctcss == 0 it should operate as you request, transmitting the input tone through the end of the transmission.
Tom KD7LXL _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
--
*Michael "Lee" Lockwood* michael@lockwood.us.com <mailto:michael@lockwood.us.com>
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Fantastic... Now I'll just patiently wait. Who am I kidding? Knowing that there's new things in the works is exciting! On Fri, Aug 11, 2017 at 10:51 AM, Steve Zingman <szingman@msgstor.com> wrote:
It will be looked at. Work is happening on channel drivers now. (among a LOT of other things)
Steve N4IRS
On 8/11/2017 11:39 AM, Michael "Lee" Lockwood wrote:
Understood, thanks Tom! I hope this does get implemented, or finalized at some point.
On Fri, Aug 11, 2017 at 10:36 AM, Tom Hayward <tom@tomh.us> wrote:
On Fri, Aug 11, 2017 at 8:28 AM, Michael "Lee" Lockwood <michael@lockwood.us.com> wrote:
Just to circle back on this topic...
I tried itxctcss = as both 1 and 0 and no difference on this.
If I'm understanding correctly, at this point app_rpt does only
transmit the "default" ctcss for the repeater tail and courtesy tone, by design. It does not transmit the other txctcss tones in the usbradio.conf file. I haven't misconfigured anything?
If I were designing it, I would have done it this way, so I think that yes it is acting as designed.
However, since the itxctcss command exists, it should follow the itxctcss command. It sounds like that piece was never implemented. This is sort of halfway between a feature request and a bug report, but I think it should be programmed so that when itxctcss == 1 it operates as it does now, and when itxctcss == 0 it should operate as you request, transmitting the input tone through the end of the transmission.
Tom KD7LXL _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/c gi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- *Michael "Lee" Lockwood* michael@lockwood.us.com
I was doing some more thinking on the ctcss topic recently. In addition to my previous request of having the repeater tail/courtesy tone transmitted using the same ctcss that it was originally received on, would it also be possible to allow only certain ctcss tones to broadcast over the linked nodes? Whereas other ctcss tones in usbradio.conf would only key the local repeater? For example: 151.4 Only keys local repeater 71.9 Keys local repeater and linked node repeaters On Fri, Aug 11, 2017 at 10:51 AM, Steve Zingman <szingman@msgstor.com> wrote:
It will be looked at. Work is happening on channel drivers now. (among a LOT of other things)
Steve N4IRS
On 8/11/2017 11:39 AM, Michael "Lee" Lockwood wrote:
Understood, thanks Tom! I hope this does get implemented, or finalized at some point.
On Fri, Aug 11, 2017 at 10:36 AM, Tom Hayward <tom@tomh.us> wrote:
On Fri, Aug 11, 2017 at 8:28 AM, Michael "Lee" Lockwood <michael@lockwood.us.com> wrote:
Just to circle back on this topic...
I tried itxctcss = as both 1 and 0 and no difference on this.
If I'm understanding correctly, at this point app_rpt does only
transmit the "default" ctcss for the repeater tail and courtesy tone, by design. It does not transmit the other txctcss tones in the usbradio.conf file. I haven't misconfigured anything?
If I were designing it, I would have done it this way, so I think that yes it is acting as designed.
However, since the itxctcss command exists, it should follow the itxctcss command. It sounds like that piece was never implemented. This is sort of halfway between a feature request and a bug report, but I think it should be programmed so that when itxctcss == 1 it operates as it does now, and when itxctcss == 0 it should operate as you request, transmitting the input tone through the end of the transmission.
Tom KD7LXL _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/c gi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
--
*Michael "Lee" Lockwood* michael@lockwood.us.com
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- *Michael "Lee" Lockwood* michael@lockwood.us.com
On Sep 27, 2017 06:54, "Michael "Lee" Lockwood" <michael@lockwood.us.com> wrote: I was doing some more thinking on the ctcss topic recently. In addition to my previous request of having the repeater tail/courtesy tone transmitted using the same ctcss that it was originally received on, would it also be possible to allow only certain ctcss tones to broadcast over the linked nodes? Whereas other ctcss tones in usbradio.conf would only key the local repeater? For example: 151.4 Only keys local repeater 71.9 Keys local repeater and linked node repeaters +1. I am also interested in this. Tom KD7LXL
On Wed, Aug 9, 2017 at 8:12 AM, Michael "Lee" Lockwood <michael@lockwood.us.com> wrote:
So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail.
Just for comparison... Around here, this behavior is considered the "proper" way to build a repeater. Tone is not encoded during the courtesy tone or tail so that these are muted at the receiver. Many people don't like listening to the courtesy tone or squelch crash, especially when scanning. It is also essential if the repeater output is being used as the input for an RF link, because you don't want courtesy tones going over the link--the would result in multiple courtesy tones on the remote repeater. If I was listening to your repeater, I would prefer no tone on the courtesy tone and tail, so that my scanner would not hang on dead air. There have been some other threads about this lately. We found that the itxctcss parameter in rpt.conf controls this behavior (although community repeater mode may override it). Check that itxctcss = 0 for the behavior you want. Tom KD7LXL
Tom, I do not have the itxctcss = line anywhere in my rpt.conf file. Where in the file should I add it? On Wed, Aug 9, 2017 at 11:28 AM, Tom Hayward <tom@tomh.us> wrote:
On Wed, Aug 9, 2017 at 8:12 AM, Michael "Lee" Lockwood <michael@lockwood.us.com> wrote:
So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail.
Just for comparison... Around here, this behavior is considered the "proper" way to build a repeater. Tone is not encoded during the courtesy tone or tail so that these are muted at the receiver. Many people don't like listening to the courtesy tone or squelch crash, especially when scanning. It is also essential if the repeater output is being used as the input for an RF link, because you don't want courtesy tones going over the link--the would result in multiple courtesy tones on the remote repeater.
If I was listening to your repeater, I would prefer no tone on the courtesy tone and tail, so that my scanner would not hang on dead air.
There have been some other threads about this lately. We found that the itxctcss parameter in rpt.conf controls this behavior (although community repeater mode may override it). Check that itxctcss = 0 for the behavior you want.
Tom KD7LXL _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- *Michael "Lee" Lockwood* michael@lockwood.us.com
participants (5)
-
Michael "Lee" Lockwood -
Neil k8it -
Steve Mahler -
Steve Zingman -
Tom Hayward