Hi tried this and no luck. I updated the BIOS no luck. I am lost. thank you Chris ________________________________ From: Jeff Carrier <k0jsc.jeff@gmail.com> To: C B <harvard5362@yahoo.com> Sent: Sunday, August 25, 2013 11:20 AM Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 I normally do this when I see this issue. I have a node that has the error frequently. 1. Remove the old source tree, grab the source tarball and uncompress into a new source tree, build it, and install it: cd /usr/src rm -rf astsrc-old mv astsrc astsrc-old wget http://x.allstarlink.org/svn-trunk.tar.gz -O- | tar xzv mv trunk astsrc cd astsrc make upgrade-acid 2. Restart asterisk astres.sh 73 de K0JSC On Sun, Aug 25, 2013 at 12:10 PM, C B <harvard5362@yahoo.com> wrote: Hi
I did what you suggested and it seems to complete without error. However it did not resolve the problem. I ran the same commands for Asterisk, still the same issue. Reran the Zaptel compile / install again and still no luck. I re-downloaded for the allstarlink.org the ISO for ACID in case what I downloaded originally was corrupt. after reinstalling I looked at the /root/acidinstall.log and I did not see anything that looked like an error. Am I forgetting something or could my hardware not be combatable? As part of this project I did install this successfully on a different computer. Any help greatly appreciated. Chris
From: Paul J. Agamata <Sysman@Xceptions.COM> To: C B <harvard5362@yahoo.com> Sent: Saturday, August 24, 2013 4:57 PM Subject: Re: [App_rpt-users] Asterisk ended with exit status 1
Log into your 'root' account and navigate to the 'zaptel' directory.
When your in there type the following:
./configure <enter> make <enter> make install <enter>
Then reboot your computer and everything should be fine. _______________________________ Paul J. Agamata WH6FM Sysman@Xceptions.COM Hilo, Hawaii
From: C B <harvard5362@yahoo.com> Reply-To: C B <harvard5362@yahoo.com> Date: Saturday, August 24, 2013 1:54 PM To: Paul Agamata <Sysman@Xceptions.COM> Subject: Re: [App_rpt-users] Asterisk ended with exit status 1
Paul Please excuse my lack knowledge here, I am very unsure of the compile / install procedure you are speaking of. is there anything you can refer me to that will contain instructions on how to do this? Is it something I did wrong? Sorry for not having a lot of experience. And thank you for your help. Chris
From: Paul J. Agamata <Sysman@Xceptions.COM> To: C B <harvard5362@yahoo.com>; "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Sent: Saturday, August 24, 2013 4:46 PM Subject: Re: [App_rpt-users] Asterisk ended with exit status 1
This is indicative of the zaptel drivers not in your kernel. Compile/Install then reboot and all should be well. The 'zaptel' directory is in the 'asterisk' source directory.
Be aware that if you update your kernel you will need to re-install the zaptel modules.
Regards, Paul
_______________________________ Paul J. Agamata WH6FM Sysman@Xceptions.COM Hilo, Hawaii
From: C B <harvard5362@yahoo.com> Date: Saturday, August 24, 2013 1:23 PM To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Subject: [App_rpt-users] Asterisk ended with exit status 1
Hi
I am attempting to build a ACID node.
After several attempts of reinstalling the ACID with the same results I am asking for some help.
All seems to complete normally, I download the configuration, reboot and the following error message keeps repeating.
mpg123: no process killed Asterisk ended with exit status 1 Asterisk died with code 1 Automatically restarting Asterisk
Computer is a HPdc5700 small form factor 1 GIG memory 500 GB SATA HDD
than you in advance for any help
Chris
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users