I had the same errors on my 64 bit computer, seems it was simply a matter of using simpleusb instead of usbradio.conf in /etc/asterisk Someone here may have an example config ... On Aug 25, 2013 11:17 AM, "C B" <harvard5362@yahoo.com> wrote:
Hi
I did what you suggested and it seems to complete without error.
However it did not resolve the problem.
I ran the same commands for Asterisk, still the same issue.
Reran the Zaptel compile / install again and still no luck.
I re-downloaded for the allstarlink.org the ISO for ACID in case what I downloaded originally was corrupt.
after reinstalling I looked at the /root/acidinstall.log and I did not see anything that looked like an error.
Am I forgetting something or could my hardware not be combatable?
As part of this project I did install this successfully on a different computer.
Any help greatly appreciated.
Chris
*From:* Paul J. Agamata <Sysman@Xceptions.COM> *To:* C B <harvard5362@yahoo.com> *Sent:* Saturday, August 24, 2013 4:57 PM *Subject:* Re: [App_rpt-users] Asterisk ended with exit status 1
Log into your 'root' account and navigate to the 'zaptel' directory.
When your in there type the following:
./configure <enter> make <enter> make install <enter>
Then reboot your computer and everything should be fine.
_______________________________ *Paul J. Agamata* *WH6FM* Sysman@Xceptions.COM Hilo, Hawaii
From: C B <harvard5362@yahoo.com> Reply-To: C B <harvard5362@yahoo.com> Date: Saturday, August 24, 2013 1:54 PM To: Paul Agamata <Sysman@Xceptions.COM> Subject: Re: [App_rpt-users] Asterisk ended with exit status 1
Paul
Please excuse my lack knowledge here, I am very unsure of the compile / install procedure you are speaking of.
is there anything you can refer me to that will contain instructions on how to do this?
Is it something I did wrong?
Sorry for not having a lot of experience.
And thank you for your help.
Chris
*From:* Paul J. Agamata <Sysman@Xceptions.COM> *To:* C B <harvard5362@yahoo.com>; "app_rpt-users@ohnosec.org" < app_rpt-users@ohnosec.org> *Sent:* Saturday, August 24, 2013 4:46 PM *Subject:* Re: [App_rpt-users] Asterisk ended with exit status 1
This is indicative of the zaptel drivers not in your kernel. Compile/Install then reboot and all should be well. The 'zaptel' directory is in the 'asterisk' source directory.
Be aware that if you update your kernel you will need to re-install the zaptel modules.
Regards, Paul
_______________________________ *Paul J. Agamata* *WH6FM* Sysman@Xceptions.COM Hilo, Hawaii
From: C B <harvard5362@yahoo.com> Date: Saturday, August 24, 2013 1:23 PM To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Subject: [App_rpt-users] Asterisk ended with exit status 1
Hi
I am attempting to build a ACID node.
After several attempts of reinstalling the ACID with the same results I am asking for some help.
All seems to complete normally, I download the configuration, reboot and the following error message keeps repeating.
mpg123: no process killed Asterisk ended with exit status 1 Asterisk died with code 1 Automatically restarting Asterisk
Computer is a HPdc5700 small form factor 1 GIG memory 500 GB SATA HDD
than you in advance for any help
Chris
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
