2 - VOTER Server Address (FQDN) (voter-demo.allstarlink.org) 3 - VOTER Server Port (667), 4 - Local Port (Override) (0) 5 - Client Password (rptnopl), 6 - Host Password (rptnopl) 7 - Tx Buffer Length (3000) 8 - GPS Data Protocol (0=NMEA, 1=TSIP) (0) 9 - GPS Serial Polarity (0=Non-Inverted, 1=Inverted) (0) 10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (2) 11 - GPS Baud Rate (4800) 12 - External CTCSS (0=Ignore, 1=Non-Inverted, 2=Inverted) (1) 13 - COR Type (0=Normal, 1=IGNORE COR, 2=No Receiver) (1) 14 - Debug Level (9) 15 - Alt. VOTER Server Address (FQDN) () 16 - Alt. VOTER Server Port (Override) (0) 17 - DSP/BEW Mode NOT SUPPORTED 18 - "Duplex Mode 3" (0=DISABLED, 1-255 Hang Time) (1/10 secs) (0) 19 - Simulcast Launch Delay (0) (approx 200 ns, 5 = 1us, > 0 to ENA SC) 97 - RX Level, 98 - Status, 99 - Save Values to EEPROM i - IP Parameters menu, o - Offline Mode Parameters menu q - Disconnect Remote Console Session, r - reboot system, d - diagnostics Enter Selection (1-27,97-99,r,q,d) : <System Time Not Set> Using Primary Voter Host (72.0.177.212) <System Time Not Set> Voter Host DNS Resolved to 96.36.57.202 <System Time Not Set> Connection Using Voter Host (96.36.57.202) <System Time Not Set> Using Primary Voter Host (96.36.57.202) Select the following Diagnostic functions: 1 - Set Initial Tone Level (and assert PTT) 2 - Display Value of DIP Switches 3 - Flash LED's in sequence 4 - Run entire diag suite c - Show Diagnostic Cable Pinouts x - Exit Diagnostic Menu (back to main menu) q - Disconnect Remote Console Session, r - reboot system Enter Selection (1-4,c,x,q,r) : 4^M Running Diagnostics... Testing PTT/External CTCSS Error - Failed to read PTT/CTCSS in un-asserted state *Testing GPS UART* *Error - Failed to read data from GPS UART* Testing level at 100 Hz for Normal Audio ^C Select the following Diagnostic functions: --- No the LED's do not come on for GPS/HST rechecked the wiring all looks right assuming GTX is transmit that goes to the GPS rx line and vice versa GPPS pin 7 is labeled as PTT out in the documentation - not sure what that means, I thought it was Gps 1pps? http://206.212.254.21/unode_docs/rtcm_%20manual.pdf P2 - DB15F D-Shell connector for the RS-232 (console @57600 bps, DCE) and GPS 1 - NC 2 - Console Transmit Data 3 - Console Receive Data 4 - NC 5 - Gnd 6 - GPS Receive Data (to White TXD on - GPS) 7 - PTT Out (to Yellow Measurement Pulse output - on GPS) 8 - Gnd (to Black - on GPS) all appear common - 9 - NC 10 - Console Request To Send (RTS) 11 - Console Clear To Send (CTS) 12 - NC 13 - GPS Power Output (5Vdc @ 800ma MAX) - (Red on - GPS) 14 - GPS Transmit Data (to green RCV on - GPS) 15 – External Reset And Yes the gps works fine in windows - not sure what I am missing -