Does anyone know the correct settings for the RTCM in a voting configuration? Menus 8 - GPS Data Protocol (0=NMEA, 1=TSIP) (0) 9 - GPS Serial Polarity (0=Non-Inverted, 1=Inverted) (0) 10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (0) I believe 8 is correct I know the baud rate is 4800 tested it on the garmin software - not sure about the serial polarity/PPS polarity - I believe it is hooked up correctly - the time shows not set on the RTCM, and I lose connection to the allstar/asterisk box - once I set PPS polarity to 2 then it reconnects - this is setup as the master site for now - Right now they are both on the same LAN - If anyone has any other example configs for voter.conf, etc that would be great too, make sure there isn't some other setting for it. 73s Mark
Having the PPS Polarity set to 2 tells the RTCM you do not have a GPS. That forces the RTCM to become a mix (non-voting) client. Turn it on, save it and restart. A simple voter.conf would look like this. [general] port = 667 password = BLAH [1000] Site1 = pswrd1,master,transmit Site2 = pswrd2,transmit -- Tim :wq On Apr 19, 2014, at 1:23 AM, Mark Johnston <markjohnston73@gmail.com> wrote:
10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (0)
Right I have a garmin 18x lvc trying to get it going as a voting site... first one.. On Apr 19, 2014 8:26 AM, "Tim Sawyer" <tim.sawyer@mac.com> wrote:
Having the PPS Polarity set to 2 tells the RTCM you do not have a GPS. That forces the RTCM to become a mix (non-voting) client. Turn it on, save it and restart. A simple voter.conf would look like this.
[general] port = 667 password = BLAH
[1000] Site1 = pswrd1,master,transmit Site2 = pswrd2,transmit
-- Tim :wq
On Apr 19, 2014, at 1:23 AM, Mark Johnston <markjohnston73@gmail.com> wrote:
10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (0)
You need to have two GPS’ in order to vote. One for the master site and one remote. -- Tim :wq On Apr 19, 2014, at 8:44 AM, Mark Johnston <markjohnston73@gmail.com> wrote:
Right I have a garmin 18x lvc trying to get it going as a voting site... first one..
On Apr 19, 2014 8:26 AM, "Tim Sawyer" <tim.sawyer@mac.com> wrote: Having the PPS Polarity set to 2 tells the RTCM you do not have a GPS. That forces the RTCM to become a mix (non-voting) client. Turn it on, save it and restart. A simple voter.conf would look like this.
[general] port = 667 password = BLAH
[1000] Site1 = pswrd1,master,transmit Site2 = pswrd2,transmit
-- Tim :wq
On Apr 19, 2014, at 1:23 AM, Mark Johnston <markjohnston73@gmail.com> wrote:
10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (0)
I just wanted to be sure everything was working before I buy a second RTCM and GPS... is there any other way to at least verify the GPS is working with this RTCM? As even the clock is never set... On Apr 19, 2014 8:59 AM, "Tim Sawyer" <tim.sawyer@mac.com> wrote:
You need to have two GPS’ in order to vote. One for the master site and one remote. -- Tim :wq
On Apr 19, 2014, at 8:44 AM, Mark Johnston <markjohnston73@gmail.com> wrote:
Right I have a garmin 18x lvc trying to get it going as a voting site... first one.. On Apr 19, 2014 8:26 AM, "Tim Sawyer" <tim.sawyer@mac.com> wrote:
Having the PPS Polarity set to 2 tells the RTCM you do not have a GPS. That forces the RTCM to become a mix (non-voting) client. Turn it on, save it and restart. A simple voter.conf would look like this.
[general] port = 667 password = BLAH
[1000] Site1 = pswrd1,master,transmit Site2 = pswrd2,transmit
-- Tim :wq
On Apr 19, 2014, at 1:23 AM, Mark Johnston <markjohnston73@gmail.com> wrote:
10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (0)
You can always use the voter-demo.allstarlink.org server to test it. Jim Date: Sat, 19 Apr 2014 09:51:35 -0700 From: markjohnston73@gmail.com To: tim.sawyer@mac.com CC: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] RTCM voting setup I just wanted to be sure everything was working before I buy a second RTCM and GPS... is there any other way to at least verify the GPS is working with this RTCM? As even the clock is never set... On Apr 19, 2014 8:59 AM, "Tim Sawyer" <tim.sawyer@mac.com> wrote: You need to have two GPS’ in order to vote. One for the master site and one remote. -- Tim :wq On Apr 19, 2014, at 8:44 AM, Mark Johnston <markjohnston73@gmail.com> wrote: Right I have a garmin 18x lvc trying to get it going as a voting site... first one.. On Apr 19, 2014 8:26 AM, "Tim Sawyer" <tim.sawyer@mac.com> wrote: Having the PPS Polarity set to 2 tells the RTCM you do not have a GPS. That forces the RTCM to become a mix (non-voting) client. Turn it on, save it and restart. A simple voter.conf would look like this. [general]port = 667password = BLAH [1000]Site1 = pswrd1,master,transmit Site2 = pswrd2,transmit --Tim:wq On Apr 19, 2014, at 1:23 AM, Mark Johnston <markjohnston73@gmail.com> wrote: 10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (0) _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
The clock should be set. Something must be wrong. The GPS light and the Host light should both come on. -- Tim :wq On Apr 19, 2014, at 9:51 AM, Mark Johnston <markjohnston73@gmail.com> wrote:
I just wanted to be sure everything was working before I buy a second RTCM and GPS... is there any other way to at least verify the GPS is working with this RTCM? As even the clock is never set...
On Apr 19, 2014 8:59 AM, "Tim Sawyer" <tim.sawyer@mac.com> wrote: You need to have two GPS’ in order to vote. One for the master site and one remote. -- Tim :wq
On Apr 19, 2014, at 8:44 AM, Mark Johnston <markjohnston73@gmail.com> wrote:
Right I have a garmin 18x lvc trying to get it going as a voting site... first one..
On Apr 19, 2014 8:26 AM, "Tim Sawyer" <tim.sawyer@mac.com> wrote: Having the PPS Polarity set to 2 tells the RTCM you do not have a GPS. That forces the RTCM to become a mix (non-voting) client. Turn it on, save it and restart. A simple voter.conf would look like this.
[general] port = 667 password = BLAH
[1000] Site1 = pswrd1,master,transmit Site2 = pswrd2,transmit
-- Tim :wq
On Apr 19, 2014, at 1:23 AM, Mark Johnston <markjohnston73@gmail.com> wrote:
10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (0)
2 - VOTER Server Address (FQDN) (voter-demo.allstarlink.org) 3 - VOTER Server Port (667), 4 - Local Port (Override) (0) 5 - Client Password (rptnopl), 6 - Host Password (rptnopl) 7 - Tx Buffer Length (3000) 8 - GPS Data Protocol (0=NMEA, 1=TSIP) (0) 9 - GPS Serial Polarity (0=Non-Inverted, 1=Inverted) (0) 10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (2) 11 - GPS Baud Rate (4800) 12 - External CTCSS (0=Ignore, 1=Non-Inverted, 2=Inverted) (1) 13 - COR Type (0=Normal, 1=IGNORE COR, 2=No Receiver) (1) 14 - Debug Level (9) 15 - Alt. VOTER Server Address (FQDN) () 16 - Alt. VOTER Server Port (Override) (0) 17 - DSP/BEW Mode NOT SUPPORTED 18 - "Duplex Mode 3" (0=DISABLED, 1-255 Hang Time) (1/10 secs) (0) 19 - Simulcast Launch Delay (0) (approx 200 ns, 5 = 1us, > 0 to ENA SC) 97 - RX Level, 98 - Status, 99 - Save Values to EEPROM i - IP Parameters menu, o - Offline Mode Parameters menu q - Disconnect Remote Console Session, r - reboot system, d - diagnostics Enter Selection (1-27,97-99,r,q,d) : <System Time Not Set> Using Primary Voter Host (72.0.177.212) <System Time Not Set> Voter Host DNS Resolved to 96.36.57.202 <System Time Not Set> Connection Using Voter Host (96.36.57.202) <System Time Not Set> Using Primary Voter Host (96.36.57.202) Select the following Diagnostic functions: 1 - Set Initial Tone Level (and assert PTT) 2 - Display Value of DIP Switches 3 - Flash LED's in sequence 4 - Run entire diag suite c - Show Diagnostic Cable Pinouts x - Exit Diagnostic Menu (back to main menu) q - Disconnect Remote Console Session, r - reboot system Enter Selection (1-4,c,x,q,r) : 4^M Running Diagnostics... Testing PTT/External CTCSS Error - Failed to read PTT/CTCSS in un-asserted state *Testing GPS UART* *Error - Failed to read data from GPS UART* Testing level at 100 Hz for Normal Audio ^C Select the following Diagnostic functions: --- No the LED's do not come on for GPS/HST rechecked the wiring all looks right assuming GTX is transmit that goes to the GPS rx line and vice versa GPPS pin 7 is labeled as PTT out in the documentation - not sure what that means, I thought it was Gps 1pps? http://206.212.254.21/unode_docs/rtcm_%20manual.pdf P2 - DB15F D-Shell connector for the RS-232 (console @57600 bps, DCE) and GPS 1 - NC 2 - Console Transmit Data 3 - Console Receive Data 4 - NC 5 - Gnd 6 - GPS Receive Data (to White TXD on - GPS) 7 - PTT Out (to Yellow Measurement Pulse output - on GPS) 8 - Gnd (to Black - on GPS) all appear common - 9 - NC 10 - Console Request To Send (RTS) 11 - Console Clear To Send (CTS) 12 - NC 13 - GPS Power Output (5Vdc @ 800ma MAX) - (Red on - GPS) 14 - GPS Transmit Data (to green RCV on - GPS) 15 – External Reset And Yes the gps works fine in windows - not sure what I am missing -
GTX goes to TX Data On Sat, Apr 19, 2014 at 11:39 PM, Tim Sawyer <tim.sawyer@mac.com> wrote:
I think that’s the problem. Reverse them. -- Tim :wq
On Apr 19, 2014, at 8:55 PM, Mark Johnston <markjohnston73@gmail.com> wrote:
assuming GTX is transmit that goes to the GPS rx line and vice versa
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Hi all, I need a voting repeater with one master site (duplex repeater) and one voting receiver. Both sites based on RTCMs. And server is a separate PC hasnt any physical connection to radio. Question: I need a 2 GPS receivers for RTCMs or I need 3 GPS (one for server) ? Thanks! Regards Mihhail Jakovlev From: app_rpt-users-bounces@ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Michael Hebert Sent: Sunday, April 20, 2014 7:42 AM To: Tim Sawyer Cc: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] RTCM voting setup GTX goes to TX Data On Sat, Apr 19, 2014 at 11:39 PM, Tim Sawyer <tim.sawyer@mac.com<mailto:tim.sawyer@mac.com>> wrote: I think that’s the problem. Reverse them. -- Tim :wq On Apr 19, 2014, at 8:55 PM, Mark Johnston <markjohnston73@gmail.com<mailto:markjohnston73@gmail.com>> wrote: assuming GTX is transmit that goes to the GPS rx line and vice versa _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org<mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
2 GPS receivers. The master site needs to be on the same subnet as the asterisk server. On Sun, Apr 20, 2014 at 4:12 AM, Mihhail Jakovlev < mihhail.jakovlev@telegrupp.ee> wrote:
Hi all,
I need a voting repeater with one master site (duplex repeater) and one voting receiver. Both sites based on RTCMs. And server is a separate PC hasnt any physical connection to radio.
Question: I need a 2 GPS receivers for RTCMs or I need 3 GPS (one for server) ?
Thanks!
Regards
Mihhail Jakovlev
*From:* app_rpt-users-bounces@ohnosec.org [mailto: app_rpt-users-bounces@ohnosec.org] *On Behalf Of *Michael Hebert *Sent:* Sunday, April 20, 2014 7:42 AM *To:* Tim Sawyer *Cc:* app_rpt-users@ohnosec.org *Subject:* Re: [App_rpt-users] RTCM voting setup
GTX goes to TX Data
On Sat, Apr 19, 2014 at 11:39 PM, Tim Sawyer <tim.sawyer@mac.com> wrote:
I think that’s the problem. Reverse them.
-- Tim :wq
On Apr 19, 2014, at 8:55 PM, Mark Johnston <markjohnston73@gmail.com> wrote:
assuming GTX is transmit that goes to the GPS rx line and vice versa
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Mark, The GPS 18x LVC is not hooked up to the RTCM correctly. The Garmin pin labeling is backwards to what you think. I learned this by trial and error on my setup. See below. Swap 6 and 14. RTCM GPS 18x LVC 6 GRX <-- Rx Data 6 Green 7 GPPS <-- Pulse Output 1 Yellow 8 GND Ground 3 Black 8 GND Ground 5 Black 13 +5V --> Vin 2 Red 14 GTX --> TX Data 4 White Then log into the rtcm and do 98 and you should see this Current Time: Sun Apr 20, 2014 04:37:02.820 Last Rx Pkt System time: 04/20/2014 03:55:35.580, diff: 2487260 msec Last Rx Pkt Timestamp time: 04/20/2014 03:55:32.064, diff: 3515 msec Last Rx Pkt index: 160, inbounds: 1 You change your debug mode to 40 and see the gps setences Mike On Sat, Apr 19, 2014 at 10:55 PM, Mark Johnston <markjohnston73@gmail.com>wrote:
2 - VOTER Server Address (FQDN) (voter-demo.allstarlink.org) 3 - VOTER Server Port (667), 4 - Local Port (Override) (0) 5 - Client Password (rptnopl), 6 - Host Password (rptnopl) 7 - Tx Buffer Length (3000) 8 - GPS Data Protocol (0=NMEA, 1=TSIP) (0) 9 - GPS Serial Polarity (0=Non-Inverted, 1=Inverted) (0) 10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (2) 11 - GPS Baud Rate (4800) 12 - External CTCSS (0=Ignore, 1=Non-Inverted, 2=Inverted) (1) 13 - COR Type (0=Normal, 1=IGNORE COR, 2=No Receiver) (1) 14 - Debug Level (9) 15 - Alt. VOTER Server Address (FQDN) () 16 - Alt. VOTER Server Port (Override) (0) 17 - DSP/BEW Mode NOT SUPPORTED 18 - "Duplex Mode 3" (0=DISABLED, 1-255 Hang Time) (1/10 secs) (0) 19 - Simulcast Launch Delay (0) (approx 200 ns, 5 = 1us, > 0 to ENA SC) 97 - RX Level, 98 - Status, 99 - Save Values to EEPROM i - IP Parameters menu, o - Offline Mode Parameters menu q - Disconnect Remote Console Session, r - reboot system, d - diagnostics
Enter Selection (1-27,97-99,r,q,d) : <System Time Not Set> Using Primary Voter Host (72.0.177.212) <System Time Not Set> Voter Host DNS Resolved to 96.36.57.202 <System Time Not Set> Connection Using Voter Host (96.36.57.202) <System Time Not Set> Using Primary Voter Host (96.36.57.202)
Select the following Diagnostic functions:
1 - Set Initial Tone Level (and assert PTT) 2 - Display Value of DIP Switches 3 - Flash LED's in sequence 4 - Run entire diag suite c - Show Diagnostic Cable Pinouts x - Exit Diagnostic Menu (back to main menu) q - Disconnect Remote Console Session, r - reboot system
Enter Selection (1-4,c,x,q,r) : 4^M
Running Diagnostics...
Testing PTT/External CTCSS Error - Failed to read PTT/CTCSS in un-asserted state *Testing GPS UART* *Error - Failed to read data from GPS UART* Testing level at 100 Hz for Normal Audio ^C
Select the following Diagnostic functions:
--- No the LED's do not come on for GPS/HST rechecked the wiring all looks right assuming GTX is transmit that goes to the GPS rx line and vice versa
GPPS pin 7 is labeled as PTT out in the documentation - not sure what that means, I thought it was Gps 1pps?
http://206.212.254.21/unode_docs/rtcm_%20manual.pdf
P2 - DB15F D-Shell connector for the RS-232 (console @57600 bps, DCE) and GPS 1 - NC 2 - Console Transmit Data 3 - Console Receive Data 4 - NC 5 - Gnd 6 - GPS Receive Data (to White TXD on - GPS) 7 - PTT Out (to Yellow Measurement Pulse output - on GPS) 8 - Gnd (to Black - on GPS) all appear common - 9 - NC 10 - Console Request To Send (RTS) 11 - Console Clear To Send (CTS) 12 - NC 13 - GPS Power Output (5Vdc @ 800ma MAX) - (Red on - GPS) 14 - GPS Transmit Data (to green RCV on - GPS) 15 – External Reset
And Yes the gps works fine in windows - not sure what I am missing -
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
participants (5)
-
Jim Duuuude -
Mark Johnston -
Michael Hebert -
Mihhail Jakovlev -
Tim Sawyer