for how long after a giben ctcss tone is reciebed do you want to use the same ctcss tx tone when would it reset to the 151.4 tone Thanks 73 Neil Sablatzky K8IT Allstar Node 41838 KITLINK Allstar Node 42087 KITLINK HUB IRLP Node exp0068 Echolink K8IT-L WIRES-X K8IT 11479 Room 21479 From: Michael "Lee" Lockwood Sent: Wednesday, August 09, 2017 11:12 AM To: app_rpt-users@lists.allstarlink.org Subject: Re: [App_rpt-users] ctcss Encode Issues A follow up to my previous email: I have multiple ctcss tone frequencies in usbradio.conf. app_rpt is decoding the incoming CTCSS (confirmed using debug), and it transmits CTCSS while someone is actively keying the repeater. However, as soon as they release PTT, app_rpt stops transmitting the corresponding CTCSS tone that was being used, and reverts to the default tone instead. So, if I key the repeater using 146.2, it broadcasts out using 146.2 and other radios hear audio just fine. But, as soon as I release PTT on the mobile/portable radio, the squelch tail is broadcast using 151.4, not 146.2. This results in the users programmed with 146.2 not hearing the courtesy tone or squelch tail. Has anyone else run in to this issue? Here's my usbradio.conf file again: [usb] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 On Mon, Aug 7, 2017 at 7:41 PM, Michael "Lee" Lockwood <michael@lockwood.us.com> wrote: Hello, I am unable to get any ctcss to be encoded during transmit, except for the tone frequency that's entered in to the txctcssdetault field. If I change that tone, the new value gets transmitted. However, all of the other tones in the txctcssfreqs are being ignored. However, I do know that the rxctcssfreqs values are being decoded. If I transmit in to the repeater using a tone not listed, or without a tone, app_rpt ignores it and does not repeat and key up the transmitter. Any assistance is greatly appreciated. Thanks in advance! Here's what's in my usbradio.conf [usb] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=151.4 rxctcssfreqs=146.2,141.3,151.4 txctcssfreqs=146.2,141.3,151.4 ;rxctcssoverride=0 carrierfrom=usb ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=0 invertptt=0 duplex=1 rxondelay=0 rxnoisefiltype=0 eeprom=0 -- Michael "Lee" Lockwood michael@lockwood.us.com -- Michael "Lee" Lockwood michael@lockwood.us.com -------------------------------------------------------------------------------- _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.