Joe: I've done this, it is working great in testing. Here are the parts ... 1) APP_RPT doesn't support all PL tones (ACID Distribution) ... I believe that this is the valid decode list (any PL can be transmitted) ... PL NOTES 67.0 69.3 Not Available in AllStar RX DSP 69.4 Not Available in AllStar RX DSP 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 118.8 DO NOT USE - 60 Hz Harmonic 123.0 127.3 131.8 DO NOT USE - DCS Turn Off Code 136.5 DO NOT USE - DCS Turn Off Code 141.3 146.2 151.4 156.7 159.8 Not Available in AllStar RX DSP 162.2 165.5 Not Available in AllStar RX DSP 167.9 171.3 Not Available in AllStar RX DSP 173.8 177.3 Not Available in AllStar RX DSP 179.9 DO NOT USE - 60 Hz harmonic 183.5 Not Available in AllStar RX DSP 186.2 189.9 Not Available in AllStar RX DSP 192.8 196.6 Not Available in AllStar RX DSP 199.5 Not Available in AllStar RX DSP 203.5 206.5 Not Available in AllStar RX DSP 210.7 218.1 225.7 229.1 Not Available in AllStar RX DSP 233.6 241.8 250.3 254.1 Not Available in AllStar RX DSP 2) The method to associate RX and TX tones and have valid decode of certain PLs in usbradio.conf is .... ; ; CTCSS / PL TONES txctcssdefault= 103.5 ; default tx ctcss freq, any frequency permitted, used when RX is quiet rxctcssfreqs= 67.0,88.5,103.5,136.5,192.8,250.3 ; rx ctcss freqs in floating point. must be in table txctcssfreqs= 67.0,88.5,103.5,103.5,192.8,250.3 ; tx ctcss freqs, any frequency permitted ; ; RECEIVER CONTROLS ; rxctcssoverride=0 ; Set to 1 or yes to start out in carrier squelch mode rxctcssrelax=0 ; reduce talkoff from radios w/o CTCSS Tx HPF ; ; (help radios with DTMF Twist) ** Note, you can cross PLs ... when the above receives 136.5 it transmits 103.5 Like I said, so far it has all worked ... just feed voice and PL from the discriminator to the AllStar server. Good Luck! ...STeve - KF5VH On 7/22/2016 10:29 AM, Joe Moskalski wrote:
I have a need to setup a community repeater. This is done easily with a shared repeater tone panel and the like from CSI. I was wondering if this could be accomplished using app_rpt. All it would need to do is allow the use of multiple input and output PL tones. Simply put, when the repeater receives X pl tone it transmits the X pl tone on the output and when the repeater receives Y pl tone it transmits the Y pl tone on the output. If anyone has done this or has any idea on how this would be accomplished it would be much appreciated. Thanks in advance!
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.