I was given an IP phone about 6 months ago.It was left at my friend home after he lost his job cause the company went bancrupt. (he was working from home) they took the laptop but never asked for the phone and router ;-) ) So I took it and it was trying to call home to download its firmware and boot.. So I did a reset, now its waiting to know what do.. The model is a polycom IP335 Would it be possible to program it so that it call my node so that I could remote monitor it.. That of course would be a learning experience about IP phone.. I also have an ATA , a grandstream ht701.. would that also work? Thanks for the time you take to answer my nooby question. Pierre
While I know nothing of the individual phone you have and perhaps someone has exact directions for you, I can give some universal notes... 1. Get a manual - probably available online. 2 most ip phones can be config'd via ip address. you should be able to use dhcp till you know what your wanting to do. 3. once you have your phone config'd for your network keep in mind you need to think ahead. issuing a sip id of 5xxx or 6xxx is probably a good starting point. give it a password, as many new types of hacks nowadays. when you get to this point, and need to config a somewhat matching config to sip.conf in your app_rpt This should start you out but some phones are unique and may require other parameters to be set. [5009] ;Portable-1 deny=0.0.0.0/0.0.0.0 username=5009 secret=yourpass dtmfmode=rfc2833 canreinvite=no context=radio-control host=dynamic trustrpid=yes sendrpid=no type=peer nat=no port=5060 qualify=yes qualifyfreq=60 transport=udp encryption=no callgroup=RPT pickupgroup=ALL dial=SIP/5009 mailbox=5009 permit=0.0.0.0/0.0.0.0 callerid=Portable-1 <5009> allow=ulaw,gsm,h263 Hope that helps... ...mike/kb8jnm
I was given an IP phone about 6 months ago.It was left at my friend home after he lost his job cause the company went bancrupt. (he was working from home) they took the laptop but never asked for the phone and router ;-) ) So I took it and it was trying to call home to download its firmware and boot.. So I did a reset, now its waiting to know what do.. The model is a polycom IP335 Would it be possible to program it so that it call my node so that I could remote monitor it.. That of course would be a learning experience about IP phone.. I also have an ATA , a grandstream ht701.. would that also work? Thanks for the time you take to answer my nooby question. Pierre
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Thanks that will be a start.. But this mean I need to open my sip port to the internet cause my node is not here.. It is at the repeater site.. or I am thinking I could make myself a small asterisk server (without app_rpt) and link that server to my node by IAX?
Date: Tue, 9 Jun 2015 19:25:47 -0400 From: mike@midnighteng.com To: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] use of an IP phone to monitor my node
While I know nothing of the individual phone you have and perhaps someone has exact directions for you, I can give some universal notes...
1. Get a manual - probably available online.
2 most ip phones can be config'd via ip address. you should be able to use dhcp till you know what your wanting to do.
3. once you have your phone config'd for your network keep in mind you need to think ahead. issuing a sip id of 5xxx or 6xxx is probably a good starting point. give it a password, as many new types of hacks nowadays.
when you get to this point, and need to config a somewhat matching config to sip.conf in your app_rpt
This should start you out but some phones are unique and may require other parameters to be set.
[5009] ;Portable-1 deny=0.0.0.0/0.0.0.0 username=5009 secret=yourpass dtmfmode=rfc2833 canreinvite=no context=radio-control host=dynamic trustrpid=yes sendrpid=no type=peer nat=no port=5060 qualify=yes qualifyfreq=60 transport=udp encryption=no callgroup=RPT pickupgroup=ALL dial=SIP/5009 mailbox=5009 permit=0.0.0.0/0.0.0.0 callerid=Portable-1 <5009> allow=ulaw,gsm,h263
Hope that helps...
...mike/kb8jnm
I was given an IP phone about 6 months ago.It was left at my friend home after he lost his job cause the company went bancrupt. (he was working from home) they took the laptop but never asked for the phone and router ;-) ) So I took it and it was trying to call home to download its firmware and boot.. So I did a reset, now its waiting to know what do.. The model is a polycom IP335 Would it be possible to program it so that it call my node so that I could remote monitor it.. That of course would be a learning experience about IP phone.. I also have an ATA , a grandstream ht701.. would that also work? Thanks for the time you take to answer my nooby question. Pierre
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
I've used several SIP VoIP phones to do exactly what you want...except my node is local to me so I deal only on the LAN side. As an administrator of VoIP systems I'll caution opening up your remote node to SIP traffic as there are a lot of bad folks out there port scanning SIP 5060 all day long. One of our Asterisk systems was being hit so many times by people trying to register a SIP phone that we finally had to shut down remote SIP registration, by using ACLs in the phone system first but this didn't stop the traffic at the router so we dropped all SIP traffic there from the Internet. A real shame because we had users who wanted to work at home and a remotely registered SIP phone would have been handy. As to the Polycom 335, these are about the easiest SIP phones to set up on any VoIP system. If you've done a factory reset then it will come up as DHCP and get an IP address from your LAN. Once you discover the IP address it has (press MENU>STATUS>NETWORK>TCPIP) you can HTTP into the phone to set up the phone's extension and registration credentials, SIP port, NTP settings, digitmap, etc.. You may need to modify the digitmap as well, look for the SIP tab at the top of the web interface and scroll down to digitmap. If your first digit for extensions is a 5 and they are 4 digits in length, for example, be sure there is a setting at the beginning of the dial plan string that looks "5xxx|" or modify the default digitmap like "[0-8]xxx|" (leave off the quotes of course). I've found it quite convenient to have a SIP phone on my LAN that is connected to my simplex node all the time. Thanks to a local ham who knows app_rpt quite well I was able to set up the extension for my simplex node so I can just dial my node number and leave the phone connected all of the time on speakerphone (receive only). I can monitor traffic, and if necessary use the phone in lieu of an HT to talk to folks using the "cop6" parameter in your RPT.CONF file to turn on transmit (*99 in my system), then dial a "#" to drop the transmit but keep the phone connected in receive-only mode. Its kind of a pain to use this sequence as a PTT, so I also keep an HT around to RF into my node to talk. Hope this was useful, enjoy! -------------------------------------------- On Tue, 6/9/15, pete M <petem001@hotmail.com> wrote: Subject: Re: [App_rpt-users] use of an IP phone to monitor my node To: "mike@midnighteng.com" <mike@midnighteng.com>, "APP RPT" <app_rpt-users@ohnosec.org> Date: Tuesday, June 9, 2015, 8:29 PM #yiv7606176711 #yiv7606176711 -- .yiv7606176711hmmessage P { margin:0px;padding:0px;} #yiv7606176711 body.yiv7606176711hmmessage { font-size:12pt;font-family:Calibri;} #yiv7606176711 Thanks that will be a start.. But this mean I need to open my sip port to the internet cause my node is not here.. It is at the repeater site.. or I am thinking I could make myself a small asterisk server (without app_rpt) and link that server to my node by IAX?
Date: Tue, 9 Jun 2015 19:25:47 -0400 From: mike@midnighteng.com To: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] use of an IP phone to monitor my node
While I know nothing of the individual phone you have and perhaps someone has exact directions for you, I can give some universal notes...
1. Get a manual - probably available online.
2 most ip phones can be config'd via ip address. you should be able to use
dhcp till you know what your wanting to do.
3. once you have
your phone config'd for your network keep in mind you
need to think ahead. issuing a sip id of 5xxx or 6xxx is probably a good
starting point. give it a password, as many new types of hacks nowadays.
when you get to this point, and need to config a somewhat matching config
to sip.conf in your app_rpt
This should start you out but some phones are unique and may require other parameters to be set.
[5009] ;Portable-1 deny=0.0.0.0/0.0.0.0 username=5009
secret=yourpass
dtmfmode=rfc2833 canreinvite=no
context=radio-control
host=dynamic trustrpid=yes
sendrpid=no
type=peer nat=no port=5060 qualify=yes
qualifyfreq=60
transport=udp encryption=no
callgroup=RPT
pickupgroup=ALL dial=SIP/5009
mailbox=5009
permit=0.0.0.0/0.0.0.0 callerid=Portable-1 <5009> allow=ulaw,gsm,h263
Hope that helps...
...mike/kb8jnm
I was given an IP phone about 6 months ago.It was left at my friend home after he lost his job cause the company went bancrupt. (he was working
from home) they took the laptop but never asked for the phone and router
;-) ) So I took it and it was trying to call home to download its firmware and
boot..
So I did a reset, now its waiting to know what do.. The model is a polycom IP335 Would it be possible to program it so that it call my node so that I could remote monitor it.. That of course would be a learning experience about IP phone.. I also have an ATA , a grandstream ht701.. would that also work? Thanks for the time you take to answer my nooby question.
Pierre
App_rpt-users mailing list App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To
unsubscribe from this list please visit
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down
to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to
the list detailing the problem.
_______________________________________________
App_rpt-users mailing list App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from
this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-----Inline Attachment Follows----- _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Thanks Bill. I did not knew about the web configuration of the phone, I was under the feeling I would have to program it from the small screen on it.. so that is a good news! But as you said it, I wont open my sip port to the web.. I will try to understand how to make a trunk in IAX2 between my asterisk at home and the repeater site.. Anyone here could tell me what would be a good distro for such a small system at home? I have a few thin client that could be used.. PIAF sound good.. I could use a small ubs stick to run my stuff.. The HD in the Thin client is 1 GB the ram is 1GB and the cpu speed is 1GHZ .. I took a look at the PFSENSE asterisk package. I run this as my router at home, the thing seem to be used by guys that knows a lot about asterisk.. I know some stuff. but not enough to venture in that game.. -----Message d'origine----- From: Bill South Sent: Wednesday, June 10, 2015 7:47 AM To: mike@midnighteng.com ; APP RPT ; pete M Subject: Re: [App_rpt-users] use of an IP phone to monitor my node I've used several SIP VoIP phones to do exactly what you want...except my node is local to me so I deal only on the LAN side. As an administrator of VoIP systems I'll caution opening up your remote node to SIP traffic as there are a lot of bad folks out there port scanning SIP 5060 all day long. One of our Asterisk systems was being hit so many times by people trying to register a SIP phone that we finally had to shut down remote SIP registration, by using ACLs in the phone system first but this didn't stop the traffic at the router so we dropped all SIP traffic there from the Internet. A real shame because we had users who wanted to work at home and a remotely registered SIP phone would have been handy. As to the Polycom 335, these are about the easiest SIP phones to set up on any VoIP system. If you've done a factory reset then it will come up as DHCP and get an IP address from your LAN. Once you discover the IP address it has (press MENU>STATUS>NETWORK>TCPIP) you can HTTP into the phone to set up the phone's extension and registration credentials, SIP port, NTP settings, digitmap, etc.. You may need to modify the digitmap as well, look for the SIP tab at the top of the web interface and scroll down to digitmap. If your first digit for extensions is a 5 and they are 4 digits in length, for example, be sure there is a setting at the beginning of the dial plan string that looks "5xxx|" or modify the default digitmap like "[0-8]xxx|" (leave off the quotes of course). I've found it quite convenient to have a SIP phone on my LAN that is connected to my simplex node all the time. Thanks to a local ham who knows app_rpt quite well I was able to set up the extension for my simplex node so I can just dial my node number and leave the phone connected all of the time on speakerphone (receive only). I can monitor traffic, and if necessary use the phone in lieu of an HT to talk to folks using the "cop6" parameter in your RPT.CONF file to turn on transmit (*99 in my system), then dial a "#" to drop the transmit but keep the phone connected in receive-only mode. Its kind of a pain to use this sequence as a PTT, so I also keep an HT around to RF into my node to talk. Hope this was useful, enjoy! -------------------------------------------- On Tue, 6/9/15, pete M <petem001@hotmail.com> wrote: Subject: Re: [App_rpt-users] use of an IP phone to monitor my node To: "mike@midnighteng.com" <mike@midnighteng.com>, "APP RPT" <app_rpt-users@ohnosec.org> Date: Tuesday, June 9, 2015, 8:29 PM #yiv7606176711 #yiv7606176711 -- .yiv7606176711hmmessage P { margin:0px;padding:0px;} #yiv7606176711 body.yiv7606176711hmmessage { font-size:12pt;font-family:Calibri;} #yiv7606176711 Thanks that will be a start.. But this mean I need to open my sip port to the internet cause my node is not here.. It is at the repeater site.. or I am thinking I could make myself a small asterisk server (without app_rpt) and link that server to my node by IAX?
Date: Tue, 9 Jun 2015 19:25:47 -0400 From: mike@midnighteng.com To: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] use of an IP phone to monitor my node
While I know nothing of the individual phone you have and perhaps someone has exact directions for you, I can give some universal notes...
1. Get a manual - probably available online.
2 most ip phones can be config'd via ip address. you should be able to use
dhcp till you know what your wanting to do.
3. once you have
your phone config'd for your network keep in mind you
need to think ahead. issuing a sip id of 5xxx or 6xxx is probably a good
starting point. give it a password, as many new types of hacks nowadays.
when you get to this point, and need to config a somewhat matching config
to sip.conf in your app_rpt
This should start you out but some phones are unique and may require other parameters to be set.
[5009] ;Portable-1 deny=0.0.0.0/0.0.0.0 username=5009
secret=yourpass
dtmfmode=rfc2833 canreinvite=no
context=radio-control
host=dynamic trustrpid=yes
sendrpid=no
type=peer nat=no port=5060 qualify=yes
qualifyfreq=60
transport=udp encryption=no
callgroup=RPT
pickupgroup=ALL dial=SIP/5009
mailbox=5009
permit=0.0.0.0/0.0.0.0 callerid=Portable-1 <5009> allow=ulaw,gsm,h263
Hope that helps...
...mike/kb8jnm
I was given an IP phone about 6 months ago.It was left at my friend home after he lost his job cause the company went bancrupt. (he was working
from home) they took the laptop but never asked for the phone and router
;-) ) So I took it and it was trying to call home to download its firmware and
boot..
So I did a reset, now its waiting to know what do.. The model is a polycom IP335 Would it be possible to program it so that it call my node so that I could remote monitor it.. That of course would be a learning experience about IP phone.. I also have an ATA , a grandstream ht701.. would that also work? Thanks for the time you take to answer my nooby question.
Pierre
App_rpt-users mailing list App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To
unsubscribe from this list please visit
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down
to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to
the list detailing the problem.
_______________________________________________
App_rpt-users mailing list App_rpt-users@ohnosec.org
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from
this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-----Inline Attachment Follows----- _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Why did I did not think of it? And I could run a small simplex node at the same time.. Got a few uv-3r that are doing nothing and at 500 mw on the tx side it wont be that bad for my other use of the vhf or uhf band, wich ever I choose to use.. Now still need to do a trunk or not? cause I could hook up my sip phone to my simplex node that would also be linked to my repeater.. Humm got to read a bit about this -----Message d'origine----- From: Tim Sawyer Sent: Wednesday, June 10, 2015 8:50 AM To: Pete M Cc: APP RPT Subject: Re: [App_rpt-users] use of an IP phone to monitor my node ACID, of course. It makes a fine home PBX. -- Tim :wq
On Jun 10, 2015, at 5:36 AM, Pete M <petem001@hotmail.com> wrote:
Anyone here could tell me what would be a good distro for such a small system at home?
You don’t even have to have a radio. I have a ZAP/Dummy node on my home PBX that I dial into to monitor our repeaters. Probably don’t need a trunk if your SIP phone is on the same LAN with your home PBX/node. You can just *3 to any node you want to go to. -- Tim :wq
On Jun 10, 2015, at 6:43 AM, Pete M <petem001@hotmail.com> wrote:
Why did I did not think of it?
And I could run a small simplex node at the same time..
Got a few uv-3r that are doing nothing and at 500 mw on the tx side it wont be that bad for my other use of the vhf or uhf band, wich ever I choose to use..
Now still need to do a trunk or not?
cause I could hook up my sip phone to my simplex node that would also be linked to my repeater..
Humm got to read a bit about this
-----Message d'origine----- From: Tim Sawyer Sent: Wednesday, June 10, 2015 8:50 AM To: Pete M Cc: APP RPT Subject: Re: [App_rpt-users] use of an IP phone to monitor my node
ACID, of course. It makes a fine home PBX. -- Tim :wq
On Jun 10, 2015, at 5:36 AM, Pete M <petem001@hotmail.com> wrote:
Anyone here could tell me what would be a good distro for such a small system at home?
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
participants (5)
-
Bill South -
mike＠midnighteng.com -
pete M -
Pete M
-
Tim Sawyer