Hello All, Could someone lease help. How do you turn off or turn the courtesy tones down. This is what I have in rpt.conf Under [telemetry] [telemetry] ; Telemetry entries can be shared across all repeaters, or defined for each repeater. ; Can be a tone sequence, morse string, or a file ; ; |t - Tone escape sequence ; ; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude) ; Single frequencies are created by setting freq1 or freq2 to zero. ; ; |m - Morse escape sequence ; ; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string ; ; |i - Morse ID escape sequence ; ; Sends Morse code at the ID amplitude and ID frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string telemdefault=2;;0=telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter 1 telemdynamic=1;;0=disallow users to change the local telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command 1 guilinkdefault=0;0= telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter, 3 = follow local telemetry mode 1 guilinkdynamic=0;0= disallow users to change the gui telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command 1 phonelinkdefault=0;0= telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter, 3 = follow local telemetry mode 1 phonelinkdynamic=0;0= disallow users to change phone telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command 1 eannmode=0; 0=do not announce Echolink nodes at all, 1 = announce only the node number (Allstar-translated), 2 = announce only the call of the echolink station, 3 = announce both 1 echolinkdefault=2; 0= telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter, 3 = follow local telemetry mode 2 echolinkdynamic=0; 0= disallow users to change current echolink telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command 1 ct1=|t(350,0,100,1000)(500,0,100,1000)(660,0,100,1000) ct2=|t(660,880,150,0) ct3=|t(440,0,150,0) ct4=|t(550,0,150,1000) ct5=|t(660,0,150,1000) ct6=|t(880,0,150,1000) ct7=|t(660,440,150,1000) ct8=|t(700,1100,150,0) remotetx=|t(1633,0,50,1000)(0,0,80,0)(1209,0,50,1000); remotemon=|t(1209,0,50,1000) cmdmode=|t(900,903,200,1000) functcomplete=|t(1000,0,100,1000)(0,0,100,0)(1000,0,100,1000) patchup=rpt/callproceeding patchdown=rpt/callterminated CT 2,3,8 I turned down amplitude to 0 but still have tones . Can someone tell me what I'm doing wrong. 73 Harry Romano KC4RPP Skype: hromano777 Phone 1-239-455-1411