See update below

On Feb 23, 2016, at 4:07 PM, kk6ecm <kk6ecm@gmail.com> wrote:

Issue with simpleusb on the Pi2. I implemented USB radio, and the problem went away. Modify modules,conf (no load simple, and load usbradio, and add usbradio.conf and usbradio_ tune_<node Numbers>.conf. Update rpt.conf. Recommend tuning per instructions.

May have missed something.

Thanks, Bob kk6ecm 73

Sent from iPad

...

On Feb 23, 2016, at 3:56 PM, gregory <dropbox@digitalattack.org> wrote:

Hi all, in duplex=2 i can hear myself for just a sec when i unkey. Is the correct was to solve this is to change to duplex=3 and wire the rx radio audio out/cod to the tx radio audio in/ptt?

hardware = kenwood tx radio, kenwood rx radio, asterisk on pi2, uri, duplexer.

wiring PDF here

w6fbw.digitalattack.org/wiring.pdf

_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

I think I understand what he's saying. It's just the usual latency combined with a really fast TR turnaround on his radio (not the repeater but whatever he's accessing the repeater with). If you listen to the output of your repeater while you're transmitting, you'll notice a bit of a delay. No way around that, I'm afraid, but that's what you're hearing. -- Buddy Brannan, KB5ELV - Erie, PA Phone: 814-860-3194 Mobile: 814-431-0962 Email: buddy@brannan.name

On Feb 23, 2016, at 7:21 PM, mike@midnighteng.com wrote:

I'm sorry O.M. your message is not clear but I'll try from what I see.

First, there is a duplex= setting in both rpt.conf and usbradio.conf I was not sure you have been changing the correct one. It's happened before....

Assuming a full duplex simple repeater,

duplex=1 in usbradio.conf... see http://ohnosec.org/drupal/node/193

duplex=2 in rpt.conf... see http://ohnosec.org/drupal/node/84

If there is some other issue, it could be in other timers/settings if you are using the correct duplex for your need. But sometimes a simple remove and replace the usb sound dongle may clean it out if you have been adjusting settings very much. If not resolved, try a hard boot and test before adjusting settings again.

...mike/kb8jnm

...

Hi all, in duplex=2 i can hear myself for just a sec when i unkey. Is the correct was to solve this is to change to duplex=3 and wire the rx radio audio out/cod to the tx radio audio in/ptt?

hardware = kenwood tx radio, kenwood rx radio, asterisk on pi2, uri, duplexer.

wiring PDF here

w6fbw.digitalattack.org/wiring.pdf

_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.