Re: [App_rpt-users] homebrew USB sound fob no RX audio
I have a question and a possible clue to the issue *Question:* Would a Dell dimension 8400 with a pentium 4 processer be able to handle two nodes at once? For the most part, the first node will only be connected to the second node and the second node will connect to remote nodes. *Possible clue to issue* So I was in the radio-tune-menu option number four, the CTCSS detection. I first did it on node Number 1 and it worked fine just like always. I then tried it on node number 2 and it didn't work and everything was 0. Then I tried it with node number 1 but the USB devices swapped. Node 1 worked, and node 2 didn't. So there is something wrong where no CTCSS will get detected and it is always 0. Here is my USBRADIO.conf ; ; Usbradio channel driver Configuration File ; [general] [usb40764] hdwtype=0 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=103.5 rxctcssfreqs=103.5 txctcssfreqs=103.5 ;rxctcssoverride=0 carrierfrom=dsp ctcssfrom=dsp rxdemod=flat txprelim=yes txlimonly=no txtoctype=phase txmixa=composite txmixb=no invertptt=0 duplex=0 rxondelay=30 rxnoisefiltype=0 eeprom=0 ;gpio=out1 gpio1 = out0 ; in, out0 or out1 gpio2 = out0 gpio4 = in ; in, out0 or out1 [usb41694] hdwtype=0 rxboost=1 txboost=0 rxctcssrelax=1 txctcssdefault=100.0 rxctcssfreqs=100.0 txctcssfreqs=100.0 ;rxctcssoverride=0 carrierfrom=usbinvert ctcssfrom=usbinvert rxdemod=flat txprelim=no txlimonly=no txtoctype=notone On Mon, Mar 2, 2015 at 1:04 PM, Skyler F <electricity440@gmail.com> wrote:
Would the green light work as a COR point? I don't know where COR is on the UV5R.
On Mon, Mar 2, 2015 at 12:04 PM, Mike Zingman <mike.zingman@gmail.com> wrote:
Yes, that is what we did.
1) set radio for RX CTCSS 2) connect audio from FOB to fixed audio from the audio pot. 3) use COR from radio. We use the 888 ( mods here may help: http://w0fcm.com/allstar-portable-node/ )
On Mon, Mar 2, 2015 at 1:56 PM, Skyler F <electricity440@gmail.com> wrote:
Did I read correctly that you are trying to use Baofeng speaker audio +
USBRadio in order to decode CTCSS? The Baofeng filters CTCSS from the RX before it hits the speaker. A little may still leak through, but not enough to work. Look on the web and you will/may find mods to pick off the carrier detect on the Baofeng. This will give you the detection you need.
There aren't any mods that I could find and people told me the speaker output is on the chip itself.
Can I use the RX CTCSS on the radio and use COR?
On Mon, Mar 2, 2015 at 10:03 AM, Mike Zingman <mike.zingman@gmail.com> wrote:
Skyler,
Did I read correctly that you are trying to use Baofeng speaker audio + USBRadio in order to decode CTCSS? The Baofeng filters CTCSS from the RX before it hits the speaker. A little may still leak through, but not enough to work. Look on the web and you will/may find mods to pick off the carrier detect on the Baofeng. This will give you the detection you need.
If I have this wrong, never mind ;-)
On Mon, Mar 2, 2015 at 10:32 AM, Skyler F <electricity440@gmail.com> wrote:
ACID
On Mon, Mar 2, 2015 at 8:28 AM, Kevin Custer <kuggie@kuggie.com> wrote:
On 3/2/2015 10:25 AM, Skyler F wrote:
USBradio
Dell desktop with pentium 4
I will check the version when I get a chance but there is so much custom built stuff on it, upgrading would probably destroy it. It is from julyish 2014
Sorry - When I asked for the version of distribution, I meant ACID or XIPAR?
-- Skyler Fennell amsatnet.info KDØWHB electricity440@gmail.com
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
-- Skyler Fennell amsatnet.info KDØWHB electricity440@gmail.com
-- Skyler Fennell amsatnet.info KDØWHB electricity440@gmail.com
-- Skyler Fennell amsatnet.info KDØWHB electricity440@gmail.com
On 03/02/2015 06:28 PM, Skyler F wrote:
I have a question and a possible clue to the issue *Question:* Would a Dell dimension 8400 with a pentium 4 processer be able to handle two nodes at once? For the most part, the first node will only be connected to the second node and the second node will connect to remote nodes.
29655, 29656 and 29657 are all running here on one box... #~> cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 4 model name : Intel(R) Pentium(R) D CPU 2.80GHz stepping : 7 cpu MHz : 2793.347 cache size : 1024 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc pni monitor ds_cpl cid cx16 xtpr lahf_lm bogomips : 5586.69 processor : 1 vendor_id : GenuineIntel cpu family : 15 model : 4 model name : Intel(R) Pentium(R) D CPU 2.80GHz stepping : 7 cpu MHz : 2793.347 cache size : 1024 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc pni monitor ds_cpl cid cx16 xtpr lahf_lm #~>cat /proc/meminfo MemTotal: 1553368 kB MemFree: 988632 kB Buffers: 160608 kB Cached: 294444 kB SwapCached: 0 kB Active: 299444 kB Inactive: 217432 kB HighTotal: 653872 kB HighFree: 286196 kB LowTotal: 899496 kB LowFree: 702436 kB SwapTotal: 1020116 kB SwapFree: 1020116 kB Dirty: 104 kB Writeback: 0 kB AnonPages: 61812 kB Mapped: 18532 kB Slab: 31192 kB PageTables: 1544 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 1796800 kB Committed_AS: 137276 kB VmallocTotal: 114680 kB VmallocUsed: 9636 kB VmallocChunk: 104172 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 Hugepagesize: 4096 kB #~> uptime 20:42:06 up 10 days, 13:29, 1 user, load average: 0.15, 0.17, 0.17
*Possible clue to issue* So I was in the radio-tune-menu option number four, the CTCSS detection. I first did it on node Number 1 and it worked fine just like always. I then tried it on node number 2 and it didn't work and everything was 0. Then I tried it with node number 1 but the USB devices swapped. Node 1 worked, and node 2 didn't. So there is something wrong where no CTCSS will get detected and it is always 0. Here is my USBRADIO.conf
You might want to find another USB buss. Seems to me I recall someone saying that there was sometimes an issue with running two usb sound fobs on the same usb buss, maybe. Sorry to be so vague, but I really don't remember -exactly-, but I -believe- it was along those lines. Your mileage may vary -Geoff/W5OMR
I haven't figured out the entire issue yet - but the remote causes asterisk to die continuously - can I block connections to my node from anything except nodes I want? If so please advise on what config file to modify - TIA ____________ Steven Donegan KK6IVC FCC General Class License SSCC/NORC Life Member, Car #86 www.sscc.us From: Geoff <ars.w5omr@gmail.com> To: app_rpt-users@ohnosec.org Sent: Monday, March 2, 2015 6:45 PM Subject: Re: [App_rpt-users] homebrew USB sound fob no RX audio On 03/02/2015 06:28 PM, Skyler F wrote: I have a question and a possible clue to the issue Question: Would a Dell dimension 8400 with a pentium 4 processer be able to handle two nodes at once? For the most part, the first node will only be connected to the second node and the second node will connect to remote nodes. 29655, 29656 and 29657 are all running here on one box... #~> cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 4 model name : Intel(R) Pentium(R) D CPU 2.80GHz stepping : 7 cpu MHz : 2793.347 cache size : 1024 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc pni monitor ds_cpl cid cx16 xtpr lahf_lm bogomips : 5586.69 processor : 1 vendor_id : GenuineIntel cpu family : 15 model : 4 model name : Intel(R) Pentium(R) D CPU 2.80GHz stepping : 7 cpu MHz : 2793.347 cache size : 1024 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc pni monitor ds_cpl cid cx16 xtpr lahf_lm #~>cat /proc/meminfo MemTotal: 1553368 kB MemFree: 988632 kB Buffers: 160608 kB Cached: 294444 kB SwapCached: 0 kB Active: 299444 kB Inactive: 217432 kB HighTotal: 653872 kB HighFree: 286196 kB LowTotal: 899496 kB LowFree: 702436 kB SwapTotal: 1020116 kB SwapFree: 1020116 kB Dirty: 104 kB Writeback: 0 kB AnonPages: 61812 kB Mapped: 18532 kB Slab: 31192 kB PageTables: 1544 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 1796800 kB Committed_AS: 137276 kB VmallocTotal: 114680 kB VmallocUsed: 9636 kB VmallocChunk: 104172 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 Hugepagesize: 4096 kB #~> uptime 20:42:06 up 10 days, 13:29, 1 user, load average: 0.15, 0.17, 0.17 Possible clue to issue So I was in the radio-tune-menu option number four, the CTCSS detection. I first did it on node Number 1 and it worked fine just like always. I then tried it on node number 2 and it didn't work and everything was 0. Then I tried it with node number 1 but the USB devices swapped. Node 1 worked, and node 2 didn't. So there is something wrong where no CTCSS will get detected and it is always 0. Here is my USBRADIO.conf You might want to find another USB buss. Seems to me I recall someone saying that there was sometimes an issue with running two usb sound fobs on the same usb buss, maybe. Sorry to be so vague, but I really don't remember -exactly-, but I -believe- it was along those lines. Your mileage may vary -Geoff/W5OMR _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
If I understand your question correctly, try changing your port forwarding UDP number in your router to something different from your Allstarlink.org registered port number (e.g. bindport=4569 in iax.conf. You can get out, but no one can link in from outside. Or just change both your UDP forwarded port number and your Allstarlink.org registered number, just in case someone has hacked your UDP port number. If you make them different, don't forget to change it back or your system won't work correctly with the Allstar system. Bob kk6ecm Sent from iPad
On Mar 4, 2015, at 12:32 PM, Steven Donegan <steve@donegan.org> wrote:
I haven't figured out the entire issue yet - but the remote causes asterisk to die continuously - can I block connections to my node from anything except nodes I want?
If so please advise on what config file to modify - TIA
____________ Steven Dong6an KK6IVC FCC General Class License SSCC/NORC Life Member, Car #86 www.sscc.us
From: Geoff <ars.w5omr@gmail.com> To: app_rpt-users@ohnosec.org Sent: Monday, March 2, 2015 6:45 PM Subject: Re: [App_rpt-users] homebrew USB sound fob no RX audio
On 03/02/2015 06:28 PM, Skyler F wrote: I have a question and a possible clue to the issue Question: Would a Dell dimension 8400 with a pentium 4 processer be able to handle two nodes at once? For the most part, the first node will only be connected to the second node and the second node will connect to remote nodes.
29655, 29656 and 29657 are all running here on one box...
#~> cat /proc/cpuinfo
processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 4 model name : Intel(R) Pentium(R) D CPU 2.80GHz stepping : 7 cpu MHz : 2793.347 cache size : 1024 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc pni monitor ds_cpl cid cx16 xtpr lahf_lm bogomips : 5586.69
processor : 1 vendor_id : GenuineIntel cpu family : 15 model : 4 model name : Intel(R) Pentium(R) D CPU 2.80GHz stepping : 7 cpu MHz : 2793.347 cache size : 1024 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc pni monitor ds_cpl cid cx16 xtpr lahf_lm
#~>cat /proc/meminfo
MemTotal: 1553368 kB MemFree: 988632 kB Buffers: 160608 kB Cached: 294444 kB SwapCached: 0 kB Active: 299444 kB Inactive: 217432 kB HighTotal: 653872 kB HighFree: 286196 kB LowTotal: 899496 kB LowFree: 702436 kB SwapTotal: 1020116 kB SwapFree: 1020116 kB Dirty: 104 kB Writeback: 0 kB AnonPages: 61812 kB Mapped: 18532 kB Slab: 31192 kB PageTables: 1544 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 1796800 kB Committed_AS: 137276 kB VmallocTotal: 114680 kB VmallocUsed: 9636 kB VmallocChunk: 104172 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 Hugepagesize: 4096 kB
#~> uptime 20:42:06 up 10 days, 13:29, 1 user, load average: 0.15, 0.17, 0.17
Possible clue to issue So I was in the radio-tune-menu option number four, the CTCSS detection. I first did it on node Number 1 and it worked fine just like always. I then tried it on node number 2 and it didn't work and everything was 0. Then I tried it with node number 1 but the USB devices swapped. Node 1 worked, and node 2 didn't. So there is something wrong where no CTCSS will get detected and it is always 0. Here is my USBRADIO.conf
You might want to find another USB buss. Seems to me I recall someone saying that there was sometimes an issue with running two usb sound fobs on the same usb buss, maybe.
Sorry to be so vague, but I really don't remember -exactly-, but I -believe- it was along those lines. Your mileage may vary
-Geoff/W5OMR
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
participants (4)
-
Geoff -
kk6ecm -
Skyler F -
Steven Donegan