I have a XIPAR node that needs a little support with pulseback removal. Never had to utilize this before, but when looking in URD.conf, I don't see the rxdelay= parameter like I do on ACID builds. I went ahead and inserted the command into the file, but there does not seem to be any action. Can someone confirm the parameter and placement? Here is my example: [usb] hdwtype=0 ; 0=std,1=dev eeprom=0 ; unless you have a cable w/eeprom duplex=0 ; 0=simplex, 1=duplex invertptt=0 ;minsigproc=0 ; minimal signal processing ;sendvoter=0 ; 0=default, no voter rssi, 1=enable voter rssi carrierfrom=usbinvert ; no,usb,usbinvert,dsp,vox ctcssfrom=no ; no,usb,dsp rxondelay=3000 ; Gets rid of the pulseback problem ;rxboost=1 ; rx input boost of 20dB rxboost=0 ; no boost rxdemod=flat ; no,speaker,flat txprelim=0 ; 1 = pre-emphasize and limit txmixa=voice ; no,voice,tone,composite txmixb=tone ; no,voice,tone,composite,auxvoice ;txctcssdefault=77.0 ;rxctcssfreqs=77.0; ;txctcssfreqs=77.0; txtoctype=notone; rxsquelchdelay=900 ; delayline in ms carrier squelch tail eliminator rxnoisefiltype=0 ; 0 for +/-5KHz, 2 for +/-2.5KHz systems Lu, KA4EPS
Really? You need a 3 second delay? -- Tim WD6AWP
On Sep 22, 2014, at 5:13 AM, Lu Vencl <vencl@att.net> wrote:
I have a XIPAR node that needs a little support with pulseback removal. Never had to utilize this before, but when looking in URD.conf, I don’t see the rxdelay= parameter like I do on ACID builds. I went ahead and inserted the command into the file, but there does not seem to be any action. Can someone confirm the parameter and placement? Here is my example: [usb]
hdwtype=0 ; 0=std,1=dev eeprom=0 ; unless you have a cable w/eeprom duplex=0 ; 0=simplex, 1=duplex invertptt=0 ;minsigproc=0 ; minimal signal processing ;sendvoter=0 ; 0=default, no voter rssi, 1=enable voter rssi
carrierfrom=usbinvert ; no,usb,usbinvert,dsp,vox ctcssfrom=no ; no,usb,dsp rxondelay=3000 ; Gets rid of the pulseback problem ;rxboost=1 ; rx input boost of 20dB rxboost=0 ; no boost rxdemod=flat ; no,speaker,flat txprelim=0 ; 1 = pre-emphasize and limit
txmixa=voice ; no,voice,tone,composite txmixb=tone ; no,voice,tone,composite,auxvoice
;txctcssdefault=77.0 ;rxctcssfreqs=77.0; ;txctcssfreqs=77.0; txtoctype=notone;
rxsquelchdelay=900 ; delayline in ms carrier squelch tail eliminator rxnoisefiltype=0 ; 0 for +/-5KHz, 2 for +/-2.5KHz systems
Lu, KA4EPS _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Just made it long to test. But not effective. Probably only need 150 ms. Lu Vencl
On Sep 22, 2014, at 9:46 AM, Tim Sawyer <tim.sawyer@mac.com> wrote:
Really? You need a 3 second delay? -- Tim WD6AWP
On Sep 22, 2014, at 5:13 AM, Lu Vencl <vencl@att.net> wrote:
I have a XIPAR node that needs a little support with pulseback removal. Never had to utilize this before, but when looking in URD.conf, I don’t see the rxdelay= parameter like I do on ACID builds. I went ahead and inserted the command into the file, but there does not seem to be any action. Can someone confirm the parameter and placement? Here is my example: [usb]
hdwtype=0 ; 0=std,1=dev eeprom=0 ; unless you have a cable w/eeprom duplex=0 ; 0=simplex, 1=duplex invertptt=0 ;minsigproc=0 ; minimal signal processing ;sendvoter=0 ; 0=default, no voter rssi, 1=enable voter rssi
carrierfrom=usbinvert ; no,usb,usbinvert,dsp,vox ctcssfrom=no ; no,usb,dsp rxondelay=3000 ; Gets rid of the pulseback problem ;rxboost=1 ; rx input boost of 20dB rxboost=0 ; no boost rxdemod=flat ; no,speaker,flat txprelim=0 ; 1 = pre-emphasize and limit
txmixa=voice ; no,voice,tone,composite txmixb=tone ; no,voice,tone,composite,auxvoice
;txctcssdefault=77.0 ;rxctcssfreqs=77.0; ;txctcssfreqs=77.0; txtoctype=notone;
rxsquelchdelay=900 ; delayline in ms carrier squelch tail eliminator rxnoisefiltype=0 ; 0 for +/-5KHz, 2 for +/-2.5KHz systems
Lu, KA4EPS _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
I'd have to dig a bit, but I believe this setting does not work as intended in XIPAR. Please stand by..... I'm sorry to have kept you waiting. In XIPAR it's txrxdelay= 20 ms intervals. Kevin On 9/22/2014 10:07 AM, Lu Vencl wrote:
Just made it long to test. But not effective. Probably only need 150 ms.
Lu Vencl
On Sep 22, 2014, at 9:46 AM, Tim Sawyer <tim.sawyer@mac.com <mailto:tim.sawyer@mac.com>> wrote:
Really? You need a 3 second delay? -- Tim WD6AWP
On Sep 22, 2014, at 5:13 AM, Lu Vencl <vencl@att.net <mailto:vencl@att.net>> wrote:
I have a XIPAR node that needs a little support with pulseback removal. Never had to utilize this before, but when looking in URD.conf, I don't see the rxdelay= parameter like I do on ACID builds. I went ahead and inserted the command into the file, but there does not seem to be any action. Can someone confirm the parameter and placement? Here is my example: [usb] hdwtype=0 ; 0=std,1=dev eeprom=0 ; unless you have a cable w/eeprom duplex=0 ; 0=simplex, 1=duplex invertptt=0 ;minsigproc=0 ; minimal signal processing ;sendvoter=0 ; 0=default, no voter rssi, 1=enable voter rssi carrierfrom=usbinvert ; no,usb,usbinvert,dsp,vox ctcssfrom=no ; no,usb,dsp rxondelay=3000 ; Gets rid of the pulseback problem ;rxboost=1 ; rx input boost of 20dB rxboost=0 ; no boost rxdemod=flat ; no,speaker,flat txprelim=0 ; 1 = pre-emphasize and limit txmixa=voice ; no,voice,tone,composite txmixb=tone ; no,voice,tone,composite,auxvoice ;txctcssdefault=77.0 ;rxctcssfreqs=77.0; ;txctcssfreqs=77.0; txtoctype=notone; rxsquelchdelay=900 ; delayline in ms carrier squelch tail eliminator rxnoisefiltype=0 ; 0 for +/-5KHz, 2 for +/-2.5KHz systems Lu, KA4EPS _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visithttp://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-usersand scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
No virus found in this message. Checked by AVG - www.avg.com <http://www.avg.com> Version: 2014.0.4765 / Virus Database: 4025/8255 - Release Date: 09/22/14
Tried this but there was no effect. I placed it in URD.conf I assume that is correct? Lu Vencl
On Sep 22, 2014, at 2:38 PM, Kevin Custer <kuggie@kuggie.com> wrote:
I'd have to dig a bit, but I believe this setting does not work as intended in XIPAR. Please stand by.....
I'm sorry to have kept you waiting.
In XIPAR it's txrxdelay= 20 ms intervals.
Kevin
On 9/22/2014 10:07 AM, Lu Vencl wrote: Just made it long to test. But not effective. Probably only need 150 ms.
Lu Vencl
On Sep 22, 2014, at 9:46 AM, Tim Sawyer <tim.sawyer@mac.com> wrote:
Really? You need a 3 second delay? -- Tim WD6AWP
On Sep 22, 2014, at 5:13 AM, Lu Vencl <vencl@att.net> wrote:
I have a XIPAR node that needs a little support with pulseback removal. Never had to utilize this before, but when looking in URD.conf, I don’t see the rxdelay= parameter like I do on ACID builds. I went ahead and inserted the command into the file, but there does not seem to be any action. Can someone confirm the parameter and placement? Here is my example: [usb]
hdwtype=0 ; 0=std,1=dev eeprom=0 ; unless you have a cable w/eeprom duplex=0 ; 0=simplex, 1=duplex invertptt=0 ;minsigproc=0 ; minimal signal processing ;sendvoter=0 ; 0=default, no voter rssi, 1=enable voter rssi
carrierfrom=usbinvert ; no,usb,usbinvert,dsp,vox ctcssfrom=no ; no,usb,dsp rxondelay=3000 ; Gets rid of the pulseback problem ;rxboost=1 ; rx input boost of 20dB rxboost=0 ; no boost rxdemod=flat ; no,speaker,flat txprelim=0 ; 1 = pre-emphasize and limit
txmixa=voice ; no,voice,tone,composite txmixb=tone ; no,voice,tone,composite,auxvoice
;txctcssdefault=77.0 ;rxctcssfreqs=77.0; ;txctcssfreqs=77.0; txtoctype=notone;
rxsquelchdelay=900 ; delayline in ms carrier squelch tail eliminator rxnoisefiltype=0 ; 0 for +/-5KHz, 2 for +/-2.5KHz systems
Lu, KA4EPS _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
No virus found in this message. Checked by AVG - www.avg.com Version: 2014.0.4765 / Virus Database: 4025/8255 - Release Date: 09/22/14
I actually did a complete reboot. Lu Vencl
On Sep 25, 2014, at 4:58 PM, Kevin Custer <kuggie@kuggie.com> wrote:
On 9/25/2014 1:05 PM, Lu Vencl wrote: Tried this but there was no effect. I placed it in URD.conf I assume that is correct?
Correct. You did a kill and a start?
On 9/25/2014 7:40 PM, Lu Vencl wrote:
I actually did a complete reboot.
Not sure then... We have a few simplex nodes that were giving us problems and when Brian implemented this parameter it totally fixed the problem. Maybe Brian can comment? Kevin
participants (3)
-
Kevin Custer -
Lu Vencl -
Tim Sawyer