Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
I don't know the device but if it has a CM108 or CM119 chip it will. Personally, I use startech sound fobs. They're easily modifiable using surface mount components and they're reliable. URI's are very good, but have my eye on the RIM as it has advantages over the URI. JK From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Sent: Friday, October 11, 2013 11:42 AM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 Do you know if the signal link USB sound card would work ???? I have ordered a uri , but I was asked if I would host a node for another repeater Richard Szajkowski On Oct 10, 2013, at 8:31 PM, Johnny Keeker <cypresstower@yahoo.com> wrote: At the least you have success. It takes about 10 minutes or less, when you first boot
before your node reports to all the other on-line nodes. Some of my nodes use a static IP and others DHCP with reserved address. Let us all know how things work out for you. Good luck Richard JK
From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Sent: Thursday, October 10, 2013 7:02 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
I now have what I think is a working system ,
For some reason it fails if I put in a static IP , but if I run with DHCP it finds the mic and runs
If I tell it to pull down the info from the server for he node it dies
I need it on a static IP for port fowarding , just like my other VoIP systems
And I did do the info on the web portal to the best I can, I entered in all the info it requested
I even got to install your device now , this will be here Tuesday because of our long weekend
Thanks for all the help
Richard Szajkowski
On Oct 10, 2013, at 6:31 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
did you Not Create an installation disk????
I thought you were past that point and sitting at the test prompt If you completed the ACID install and got the test prompt the password is 'setup' once your in root type passwd and change it nodesetup.sh will run the script to push your node config files from the allstar server to your node "provided you created and saved the files prior to your ACID installation" JK
From: "zeppelin.1@netzero.com" <zeppelin.1@netzero.com> To: app_rpt-users@ohnosec.org Sent: Thursday, October 10, 2013 5:20 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Hello Richard and welcome to the Linux world; You "must" do a CD BURN to the ISO for it to work properly, low speed is best for older CD ROM. 73 Anton/ KC2RQR Node 29103
---------- Original Message ---------- From: app_rpt-users-request@ohnosec.org To: app_rpt-users@ohnosec.org Subject: App_rpt-users Digest, Vol 56, Issue 20 Date: Thu, 10 Oct 2013 12:00:01 -0400
Send App_rpt-users mailing list submissions to app_rpt-users@ohnosec.org
To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request@ohnosec.org
You can reach the person managing the list at app_rpt-users-owner@ohnosec.org
When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..."
Today's Topics:
1. Help with new install (Richard Szajkowski)
----------------------------------------------------------------------
Message: 1 Date: Wed, 9 Oct 2013 18:14:55 -0400 From: Richard Szajkowski <va3rzs@gmail.com> To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Subject: [App_rpt-users] Help with new install Message-ID: <B2A7C8C9-28C3-4A33-8F56-558F97D69D7D@gmail.com> Content-Type: text/plain; charset=us-ascii
Hello to the group
I am trying to get the computer on line while my interface is shipped
I downloaded the ISO off the website , followed the prompts , I am not at a prompt Test >
I did not enter a root password as I was not asked
I can't find a PDF or anything on 1st time installs
Any help would be great
Thanks
Richard Szajkowski va3rzs
------------------------------
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
End of App_rpt-users Digest, Vol 56, Issue 20 ********************************************* ____________________________________________________________ NetZero now offers 4G mobile broadband. Sign up now. _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________
App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
... but have my eye on the RIM as it has advantages over the URI. <-- We have several RB-RIMs in stock and ready to ship.
Scott Scott Zimmerman Amateur Radio Call N3XCC 474 Barnett Road Boswell, PA 15531 On 10/11/2013 12:43 PM, Johnny Keeker wrote:
I don't know the device but if it has a CM108 or CM119 chip it will. Personally, I use startech sound fobs.They're easily modifiable using surface mount components and they're reliable. URI's are very good, but have my eye on the RIM as it has advantages over the URI. JK *From:* Richard Szajkowski <va3rzs@gmail.com> *To:* Johnny Keeker <cypresstower@yahoo.com> *Sent:* Friday, October 11, 2013 11:42 AM *Subject:* Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Do you know if the signal link USB sound card would work ???? I have ordered a uri , but I was asked if I would host a node for another repeater
Richard Szajkowski
On Oct 10, 2013, at 8:31 PM, Johnny Keeker <cypresstower@yahoo.com <mailto:cypresstower@yahoo.com>> wrote:
At the least you have success. It takes about 10 minutes or less, when you first boot before your node reports to all the other on-linenodes. Some of my nodes use a static IP and others DHCP with reserved address. Let us all know how things work out for you. Good luck Richard JK
*From:* Richard Szajkowski <va3rzs@gmail.com <mailto:va3rzs@gmail.com>> *To:* Johnny Keeker <cypresstower@yahoo.com <mailto:cypresstower@yahoo.com>> *Sent:* Thursday, October 10, 2013 7:02 PM *Subject:* Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
I now have what I think is a working system ,
For some reason it fails if I put in a static IP , but if I run with DHCP it finds the mic and runs
If I tell it to pull down the info from the server for he node it dies
I need it on a static IP for port fowarding , just like my other VoIP systems
And I did do the info on the web portal to the best I can, I entered in all the info it requested
I even got to install your device now , this will be here Tuesday because of our long weekend
Thanks for all the help
Richard Szajkowski
On Oct 10, 2013, at 6:31 PM, Johnny Keeker <cypresstower@yahoo.com <mailto:cypresstower@yahoo.com>> wrote:
did you Not Create an installation disk???? I thought you were past that point and sitting at the test prompt If you completed the ACID install and got the test prompt the password is 'setup' once your in root type passwd and change it nodesetup.sh will run the script to push your node config files from the allstar server to your node "provided you created and saved the files prior to your ACID installation" JK
*From:* "zeppelin.1@netzero.com <mailto:zeppelin.1@netzero.com>" <zeppelin.1@netzero.com <mailto:zeppelin.1@netzero.com>> *To:* app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org> *Sent:* Thursday, October 10, 2013 5:20 PM *Subject:* Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Hello Richard and welcome to the Linux world; You "must" do a CD BURN to the ISO for it to work properly, low speed is best for older CD ROM. 73 Anton/ KC2RQR Node 29103
---------- Original Message ---------- From: app_rpt-users-request@ohnosec.org <mailto:app_rpt-users-request@ohnosec.org> To: app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org> Subject: App_rpt-users Digest, Vol 56, Issue 20 Date: Thu, 10 Oct 2013 12:00:01 -0400
Send App_rpt-users mailing list submissions to app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org>
To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request@ohnosec.org <mailto:app_rpt-users-request@ohnosec.org>
You can reach the person managing the list at app_rpt-users-owner@ohnosec.org <mailto:app_rpt-users-owner@ohnosec.org>
When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..."
Today's Topics:
1. Help with new install (Richard Szajkowski)
----------------------------------------------------------------------
Message: 1 Date: Wed, 9 Oct 2013 18:14:55 -0400 From: Richard Szajkowski <va3rzs@gmail.com <mailto:va3rzs@gmail.com>> To: "app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org>" <app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org>> Subject: [App_rpt-users] Help with new install Message-ID: <B2A7C8C9-28C3-4A33-8F56-558F97D69D7D@gmail.com <mailto:B2A7C8C9-28C3-4A33-8F56-558F97D69D7D@gmail.com>> Content-Type: text/plain; charset=us-ascii
Hello to the group
I am trying to get the computer on line while my interface is shipped
I downloaded the ISO off the website , followed the prompts , I am not at a prompt Test >
I did not enter a root password as I was not asked
I can't find a PDF or anything on 1st time installs
Any help would be great
Thanks
Richard Szajkowski va3rzs
------------------------------
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
End of App_rpt-users Digest, Vol 56, Issue 20 ********************************************* ____________________________________________________________ NetZero now offers 4G mobile broadband. Sign up now. <http://www.netzero.net/?refcd=NZINTISP0512T4GOUT1>
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
yeah, Im SURE you do...
Date: Fri, 11 Oct 2013 12:56:06 -0400 From: n3xcc@repeater-builder.com To: app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
... but have my eye on the RIM as it has advantages over the URI. <-- We have several RB-RIMs in stock and ready to ship.
Scott
Scott Zimmerman Amateur Radio Call N3XCC 474 Barnett Road Boswell, PA 15531
On 10/11/2013 12:43 PM, Johnny Keeker wrote:
I don't know the device but if it has a CM108 or CM119 chip it will. Personally, I use startech sound fobs.They're easily modifiable using surface mount components and they're reliable. URI's are very good, but have my eye on the RIM as it has advantages over the URI. JK *From:* Richard Szajkowski <va3rzs@gmail.com> *To:* Johnny Keeker <cypresstower@yahoo.com> *Sent:* Friday, October 11, 2013 11:42 AM *Subject:* Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Do you know if the signal link USB sound card would work ???? I have ordered a uri , but I was asked if I would host a node for another repeater
Richard Szajkowski
On Oct 10, 2013, at 8:31 PM, Johnny Keeker <cypresstower@yahoo.com <mailto:cypresstower@yahoo.com>> wrote:
At the least you have success. It takes about 10 minutes or less, when you first boot before your node reports to all the other on-linenodes. Some of my nodes use a static IP and others DHCP with reserved address. Let us all know how things work out for you. Good luck Richard JK
*From:* Richard Szajkowski <va3rzs@gmail.com <mailto:va3rzs@gmail.com>> *To:* Johnny Keeker <cypresstower@yahoo.com <mailto:cypresstower@yahoo.com>> *Sent:* Thursday, October 10, 2013 7:02 PM *Subject:* Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
I now have what I think is a working system ,
For some reason it fails if I put in a static IP , but if I run with DHCP it finds the mic and runs
If I tell it to pull down the info from the server for he node it dies
I need it on a static IP for port fowarding , just like my other VoIP systems
And I did do the info on the web portal to the best I can, I entered in all the info it requested
I even got to install your device now , this will be here Tuesday because of our long weekend
Thanks for all the help
Richard Szajkowski
On Oct 10, 2013, at 6:31 PM, Johnny Keeker <cypresstower@yahoo.com <mailto:cypresstower@yahoo.com>> wrote:
did you Not Create an installation disk???? I thought you were past that point and sitting at the test prompt If you completed the ACID install and got the test prompt the password is 'setup' once your in root type passwd and change it nodesetup.sh will run the script to push your node config files from the allstar server to your node "provided you created and saved the files prior to your ACID installation" JK
*From:* "zeppelin.1@netzero.com <mailto:zeppelin.1@netzero.com>" <zeppelin.1@netzero.com <mailto:zeppelin.1@netzero.com>> *To:* app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org> *Sent:* Thursday, October 10, 2013 5:20 PM *Subject:* Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Hello Richard and welcome to the Linux world; You "must" do a CD BURN to the ISO for it to work properly, low speed is best for older CD ROM. 73 Anton/ KC2RQR Node 29103
---------- Original Message ---------- From: app_rpt-users-request@ohnosec.org <mailto:app_rpt-users-request@ohnosec.org> To: app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org> Subject: App_rpt-users Digest, Vol 56, Issue 20 Date: Thu, 10 Oct 2013 12:00:01 -0400
Send App_rpt-users mailing list submissions to app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org>
To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request@ohnosec.org <mailto:app_rpt-users-request@ohnosec.org>
You can reach the person managing the list at app_rpt-users-owner@ohnosec.org <mailto:app_rpt-users-owner@ohnosec.org>
When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..."
Today's Topics:
1. Help with new install (Richard Szajkowski)
----------------------------------------------------------------------
Message: 1 Date: Wed, 9 Oct 2013 18:14:55 -0400 From: Richard Szajkowski <va3rzs@gmail.com <mailto:va3rzs@gmail.com>> To: "app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org>" <app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org>> Subject: [App_rpt-users] Help with new install Message-ID: <B2A7C8C9-28C3-4A33-8F56-558F97D69D7D@gmail.com <mailto:B2A7C8C9-28C3-4A33-8F56-558F97D69D7D@gmail.com>> Content-Type: text/plain; charset=us-ascii
Hello to the group
I am trying to get the computer on line while my interface is shipped
I downloaded the ISO off the website , followed the prompts , I am not at a prompt Test >
I did not enter a root password as I was not asked
I can't find a PDF or anything on 1st time installs
Any help would be great
Thanks
Richard Szajkowski va3rzs
------------------------------
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
End of App_rpt-users Digest, Vol 56, Issue 20 ********************************************* ____________________________________________________________ NetZero now offers 4G mobile broadband. Sign up now. <http://www.netzero.net/?refcd=NZINTISP0512T4GOUT1>
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
How will I know if it works after I plug it in ? Is there a script that I need to run it install it I am finding the docs out of date or not there at all (some links are dead like for the 4 port card) I know IRLP is not supported any more , sad as I run an IRLP node , and would have liked to run all 3 networks on one computer , to save a port for the 220 repeater I thank you for all your help , Richard Szajkowski
On Oct 11, 2013, at 12:43 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
I don't know the device but if it has a CM108 or CM119 chip it will. Personally, I use startech sound fobs. They're easily modifiable using surface mount components and they're reliable. URI's are very good, but have my eye on the RIM as it has advantages over the URI. JK From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Sent: Friday, October 11, 2013 11:42 AM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Do you know if the signal link USB sound card would work ???? I have ordered a uri , but I was asked if I would host a node for another repeater
Richard Szajkowski
On Oct 10, 2013, at 8:31 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
At the least you have success. It takes about 10 minutes or less, when you first boot before your node reports to all the other on-line nodes. Some of my nodes use a static IP and others DHCP with reserved address. Let us all know how things work out for you. Good luck Richard JK
From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Sent: Thursday, October 10, 2013 7:02 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
I now have what I think is a working system ,
For some reason it fails if I put in a static IP , but if I run with DHCP it finds the mic and runs
If I tell it to pull down the info from the server for he node it dies
I need it on a static IP for port fowarding , just like my other VoIP systems
And I did do the info on the web portal to the best I can, I entered in all the info it requested
I even got to install your device now , this will be here Tuesday because of our long weekend
Thanks for all the help
Richard Szajkowski
On Oct 10, 2013, at 6:31 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
did you Not Create an installation disk???? I thought you were past that point and sitting at the test prompt If you completed the ACID install and got the test prompt the password is 'setup' once your in root type passwd and change it nodesetup.sh will run the script to push your node config files from the allstar server to your node "provided you created and saved the files prior to your ACID installation" JK
From: "zeppelin.1@netzero.com" <zeppelin.1@netzero.com> To: app_rpt-users@ohnosec.org Sent: Thursday, October 10, 2013 5:20 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Hello Richard and welcome to the Linux world; You "must" do a CD BURN to the ISO for it to work properly, low speed is best for older CD ROM. 73 Anton/ KC2RQR Node 29103
---------- Original Message ---------- From: app_rpt-users-request@ohnosec.org To: app_rpt-users@ohnosec.org Subject: App_rpt-users Digest, Vol 56, Issue 20 Date: Thu, 10 Oct 2013 12:00:01 -0400
Send App_rpt-users mailing list submissions to app_rpt-users@ohnosec.org
To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request@ohnosec.org
You can reach the person managing the list at app_rpt-users-owner@ohnosec.org
When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..."
Today's Topics:
1. Help with new install (Richard Szajkowski)
----------------------------------------------------------------------
Message: 1 Date: Wed, 9 Oct 2013 18:14:55 -0400 From: Richard Szajkowski <va3rzs@gmail.com> To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Subject: [App_rpt-users] Help with new install Message-ID: <B2A7C8C9-28C3-4A33-8F56-558F97D69D7D@gmail.com> Content-Type: text/plain; charset=us-ascii
Hello to the group
I am trying to get the computer on line while my interface is shipped
I downloaded the ISO off the website , followed the prompts , I am not at a prompt Test >
I did not enter a root password as I was not asked
I can't find a PDF or anything on 1st time installs
Any help would be great
Thanks
Richard Szajkowski va3rzs
------------------------------
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
End of App_rpt-users Digest, Vol 56, Issue 20 ********************************************* ____________________________________________________________ NetZero now offers 4G mobile broadband. Sign up now.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
Plug in your URI, RIM, or usb sound device and you will see it pop up on the linux screen as [root@~] radio-tune-menu the radio tune menu will allow you to setup your sound devices provided your .conf files are correct ACID is a repeater controller if you have 2 URIs or RIMs you can bridge your IRLP node beside IRLP configured on an ACID install had some audio level issues. Not sure about Xipar but it also had configs for IRLP. I only tested it on ACID p.s. Scott I noticed you seen the publicizing for the RIM JK From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Cc: App_rpt Users <app_rpt-users@ohnosec.org> Sent: Friday, October 11, 2013 1:06 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 How will I know if it works after I plug it in ? Is there a script that I need to run it install it I am finding the docs out of date or not there at all (some links are dead like for the 4 port card) I know IRLP is not supported any more , sad as I run an IRLP node , and would have liked to run all 3 networks on one computer , to save a port for the 220 repeater I thank you for all your help , Richard Szajkowski On Oct 11, 2013, at 12:43 PM, Johnny Keeker <cypresstower@yahoo.com> wrote: I don't know the device but if it has a CM108 or CM119 chip it will.
Personally, I use startech sound fobs. They're easily modifiable using surface mount components and they're reliable. URI's are very good, but have my eye on the RIM as it has advantages over the URI. JK
From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Sent: Friday, October 11, 2013 11:42 AM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Do you know if the signal link USB sound card would work ???? I have ordered a uri , but I was asked if I would host a node for another repeater
Richard Szajkowski
On Oct 10, 2013, at 8:31 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
At the least you have success. It takes about 10 minutes or less, when you first boot
before your node reports to all the other on-line nodes. Some of my nodes use a static IP and others DHCP with reserved address. Let us all know how things work out for you. Good luck Richard JK
From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Sent: Thursday, October 10, 2013 7:02 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
I now have what I think is a working system ,
For some reason it fails if I put in a static IP , but if I run with DHCP it finds the mic and runs
If I tell it to pull down the info from the server for he node it dies
I need it on a static IP for port fowarding , just like my other VoIP systems
And I did do the info on the web portal to the best I can, I entered in all the info it requested
I even got to install your device now , this will be here Tuesday because of our long weekend
Thanks for all the help
Richard Szajkowski
On Oct 10, 2013, at 6:31 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
did you Not Create an installation disk????
I thought you were past that point and sitting at the test prompt If you completed the ACID install and got the test prompt the password is 'setup' once your in root type passwd and change it nodesetup.sh will run the script to push your node config files from the allstar server to your node "provided you created and saved the files prior to your ACID installation" JK
From: "zeppelin.1@netzero.com" <zeppelin.1@netzero.com> To: app_rpt-users@ohnosec.org Sent: Thursday, October 10, 2013 5:20 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Hello Richard and welcome to the Linux world; You "must" do a CD BURN to the ISO for it to work properly, low speed is best for older CD ROM. 73 Anton/ KC2RQR Node 29103
---------- Original Message ---------- From: app_rpt-users-request@ohnosec.org To: app_rpt-users@ohnosec.org Subject: App_rpt-users Digest, Vol 56, Issue 20 Date: Thu, 10 Oct 2013 12:00:01 -0400
Send App_rpt-users mailing list submissions to app_rpt-users@ohnosec.org
To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request@ohnosec.org
You can reach the person managing the list at app_rpt-users-owner@ohnosec.org
When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..."
Today's Topics:
1. Help with new install (Richard Szajkowski)
----------------------------------------------------------------------
Message: 1 Date: Wed, 9 Oct 2013 18:14:55 -0400 From: Richard Szajkowski <va3rzs@gmail.com> To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Subject: [App_rpt-users] Help with new install Message-ID: <B2A7C8C9-28C3-4A33-8F56-558F97D69D7D@gmail.com> Content-Type: text/plain; charset=us-ascii
Hello to the group
I am trying to get the computer on line while my interface is shipped
I downloaded the ISO off the website , followed the prompts , I am not at a prompt Test >
I did not enter a root password as I was not asked
I can't find a PDF or anything on 1st time installs
Any help would be great
Thanks
Richard Szajkowski va3rzs
------------------------------
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
End of App_rpt-users Digest, Vol 56, Issue 20 ********************************************* ____________________________________________________________ NetZero now offers 4G mobile broadband. Sign up now. _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________
App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
and if you bridge allstar (superior and more flexible) to IRLP (old 1990s technology held together with patches and gyrations), Mr Cameron will get his shorts in a wad and cancel your credentials (but leave you listed as an active node to hide the fact that his numbers of real nodes is less than it was...). yeah, it still has some mindshare (especially amongst the dinosaurs in the ARRL, who refuse to acknowledge that allstar exists...and despite the population of a* approaching that of the older stuff, have refused to list our nodes as such in the repeater directory...), but progress waits for no man. -- Bryan Sent from my iPad
On Oct 11, 2013, at 1:47 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
Plug in your URI, RIM, or usb sound device and you will see it pop up on the linux screen as [root@~] radio-tune-menu the radio tune menu will allow you to setup your sound devices provided your .conf files are correct ACID is a repeater controller if you have 2 URIs or RIMs you can bridge your IRLP node beside IRLP configured on an ACID install had some audio level issues. Not sure about Xipar but it also had configs for IRLP. I only tested it on ACID p.s. Scott I noticed you seen the publicizing for the RIM JK
From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Cc: App_rpt Users <app_rpt-users@ohnosec.org> Sent: Friday, October 11, 2013 1:06 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
How will I know if it works after I plug it in ? Is there a script that I need to run it install it
I am finding the docs out of date or not there at all (some links are dead like for the 4 port card)
I know IRLP is not supported any more , sad as I run an IRLP node , and would have liked to run all 3 networks on one computer , to save a port for the 220 repeater
I thank you for all your help ,
Richard Szajkowski
On Oct 11, 2013, at 12:43 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
I don't know the device but if it has a CM108 or CM119 chip it will. Personally, I use startech sound fobs. They're easily modifiable using surface mount components and they're reliable. URI's are very good, but have my eye on the RIM as it has advantages over the URI. JK From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Sent: Friday, October 11, 2013 11:42 AM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Do you know if the signal link USB sound card would work ???? I have ordered a uri , but I was asked if I would host a node for another repeater
Richard Szajkowski
On Oct 10, 2013, at 8:31 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
At the least you have success. It takes about 10 minutes or less, when you first boot before your node reports to all the other on-line nodes. Some of my nodes use a static IP and others DHCP with reserved address. Let us all know how things work out for you. Good luck Richard JK
From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Sent: Thursday, October 10, 2013 7:02 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
I now have what I think is a working system ,
For some reason it fails if I put in a static IP , but if I run with DHCP it finds the mic and runs
If I tell it to pull down the info from the server for he node it dies
I need it on a static IP for port fowarding , just like my other VoIP systems
And I did do the info on the web portal to the best I can, I entered in all the info it requested
I even got to install your device now , this will be here Tuesday because of our long weekend
Thanks for all the help
Richard Szajkowski
On Oct 10, 2013, at 6:31 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
did you Not Create an installation disk???? I thought you were past that point and sitting at the test prompt If you completed the ACID install and got the test prompt the password is 'setup' once your in root type passwd and change it nodesetup.sh will run the script to push your node config files from the allstar server to your node "provided you created and saved the files prior to your ACID installation" JK
From: "zeppelin.1@netzero.com" <zeppelin.1@netzero.com> To: app_rpt-users@ohnosec.org Sent: Thursday, October 10, 2013 5:20 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Hello Richard and welcome to the Linux world; You "must" do a CD BURN to the ISO for it to work properly, low speed is best for older CD ROM. 73 Anton/ KC2RQR Node 29103
---------- Original Message ---------- From: app_rpt-users-request@ohnosec.org To: app_rpt-users@ohnosec.org Subject: App_rpt-users Digest, Vol 56, Issue 20 Date: Thu, 10 Oct 2013 12:00:01 -0400
Send App_rpt-users mailing list submissions to app_rpt-users@ohnosec.org
To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request@ohnosec.org
You can reach the person managing the list at app_rpt-users-owner@ohnosec.org
When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..."
Today's Topics:
1. Help with new install (Richard Szajkowski)
----------------------------------------------------------------------
Message: 1 Date: Wed, 9 Oct 2013 18:14:55 -0400 From: Richard Szajkowski <va3rzs@gmail.com> To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Subject: [App_rpt-users] Help with new install Message-ID: <B2A7C8C9-28C3-4A33-8F56-558F97D69D7D@gmail.com> Content-Type: text/plain; charset=us-ascii
Hello to the group
I am trying to get the computer on line while my interface is shipped
I downloaded the ISO off the website , followed the prompts , I am not at a prompt Test >
I did not enter a root password as I was not asked
I can't find a PDF or anything on 1st time installs
Any help would be great
Thanks
Richard Szajkowski va3rzs
------------------------------
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
End of App_rpt-users Digest, Vol 56, Issue 20 ********************************************* ____________________________________________________________ NetZero now offers 4G mobile broadband. Sign up now.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
good man! JK From: Bryan D. Boyle <bdboyle@bdboyle.com> To: app_rpt-users@ohnosec.org Sent: Friday, October 11, 2013 2:54 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20 and if you bridge allstar (superior and more flexible) to IRLP (old 1990s technology held together with patches and gyrations), Mr Cameron will get his shorts in a wad and cancel your credentials (but leave you listed as an active node to hide the fact that his numbers of real nodes is less than it was...). yeah, it still has some mindshare (especially amongst the dinosaurs in the ARRL, who refuse to acknowledge that allstar exists...and despite the population of a* approaching that of the older stuff, have refused to list our nodes as such in the repeater directory...), but progress waits for no man. -- BryanSent from my iPad On Oct 11, 2013, at 1:47 PM, Johnny Keeker <cypresstower@yahoo.com> wrote: Plug in your URI, RIM, or usb sound device and you will see it pop up on the linux screen
as [root@~] radio-tune-menu the radio tune menu will allow you to setup your sound devices provided your .conf files are correct ACID is a repeater controller if you have 2 URIs or RIMs you can bridge your IRLP node beside IRLP configured on an ACID install had some audio level issues. Not sure about Xipar but it also had configs for IRLP. I only tested it on ACID p.s. Scott I noticed you seen the publicizing for the RIM JK
From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Cc: App_rpt Users <app_rpt-users@ohnosec.org> Sent: Friday, October 11, 2013 1:06 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
How will I know if it works after I plug it in ? Is there a script that I need to run it install it
I am finding the docs out of date or not there at all (some links are dead like for the 4 port card)
I know IRLP is not supported any more , sad as I run an IRLP node , and would have liked to run all 3 networks on one computer , to save a port for the 220 repeater
I thank you for all your help ,
Richard Szajkowski
On Oct 11, 2013, at 12:43 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
I don't know the device but if it has a CM108 or CM119 chip it will.
Personally, I use startech sound fobs. They're easily modifiable using surface mount components and they're reliable. URI's are very good, but have my eye on the RIM as it has advantages over the URI. JK
From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Sent: Friday, October 11, 2013 11:42 AM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Do you know if the signal link USB sound card would work ???? I have ordered a uri , but I was asked if I would host a node for another repeater
Richard Szajkowski
On Oct 10, 2013, at 8:31 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
At the least you have success. It takes about 10 minutes or less, when you first boot
before your node reports to all the other on-line nodes. Some of my nodes use a static IP and others DHCP with reserved address. Let us all know how things work out for you. Good luck Richard JK
From: Richard Szajkowski <va3rzs@gmail.com> To: Johnny Keeker <cypresstower@yahoo.com> Sent: Thursday, October 10, 2013 7:02 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
I now have what I think is a working system ,
For some reason it fails if I put in a static IP , but if I run with DHCP it finds the mic and runs
If I tell it to pull down the info from the server for he node it dies
I need it on a static IP for port fowarding , just like my other VoIP systems
And I did do the info on the web portal to the best I can, I entered in all the info it requested
I even got to install your device now , this will be here Tuesday because of our long weekend
Thanks for all the help
Richard Szajkowski
On Oct 10, 2013, at 6:31 PM, Johnny Keeker <cypresstower@yahoo.com> wrote:
did you Not Create an installation disk????
I thought you were past that point and sitting at the test prompt If you completed the ACID install and got the test prompt the password is 'setup' once your in root type passwd and change it nodesetup.sh will run the script to push your node config files from the allstar server to your node "provided you created and saved the files prior to your ACID installation" JK
From: "zeppelin.1@netzero.com" <zeppelin.1@netzero.com> To: app_rpt-users@ohnosec.org Sent: Thursday, October 10, 2013 5:20 PM Subject: Re: [App_rpt-users] App_rpt-users Digest, Vol 56, Issue 20
Hello Richard and welcome to the Linux world; You "must" do a CD BURN to the ISO for it to work properly, low speed is best for older CD ROM. 73 Anton/ KC2RQR Node 29103
---------- Original Message ---------- From: app_rpt-users-request@ohnosec.org To: app_rpt-users@ohnosec.org Subject: App_rpt-users Digest, Vol 56, Issue 20 Date: Thu, 10 Oct 2013 12:00:01 -0400
Send App_rpt-users mailing list submissions to app_rpt-users@ohnosec.org
To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request@ohnosec.org
You can reach the person managing the list at app_rpt-users-owner@ohnosec.org
When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..."
Today's Topics:
1. Help with new install (Richard Szajkowski)
----------------------------------------------------------------------
Message: 1 Date: Wed, 9 Oct 2013 18:14:55 -0400 From: Richard Szajkowski <va3rzs@gmail.com> To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org> Subject: [App_rpt-users] Help with new install Message-ID: <B2A7C8C9-28C3-4A33-8F56-558F97D69D7D@gmail.com> Content-Type: text/plain; charset=us-ascii
Hello to the group
I am trying to get the computer on line while my interface is shipped
I downloaded the ISO off the website , followed the prompts , I am not at a prompt Test >
I did not enter a root password as I was not asked
I can't find a PDF or anything on 1st time installs
Any help would be great
Thanks
Richard Szajkowski va3rzs
------------------------------
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
End of App_rpt-users Digest, Vol 56, Issue 20 *********************************************
____________________________________________________________ NetZero now offers 4G mobile broadband. Sign up now. _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________
App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________
App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
participants (5)
-
Bryan D. Boyle -
Jim Duuuude -
Johnny Keeker -
Richard Szajkowski -
Scott Zimmerman