[App_rpt-users] TX Tone Drop out Time

[Bryan D. Boyle]

only if, in a subdirectory called 'custom' in /etc/asterisk, you created a file called usbradio.conf.  in other words, no, you don't uncomment it if you haven't.

--
Bryan
Sent from my iPhone
please forgive misspellings...



On Sep 17, 2012, at 18:56, "Mike Wolthuis" <wolthuis at gmail.com> wrote:

> I tried to put the following two lines into my beagle.conf
> txtoctype=notone
> txctcssdefault=131.8
>  
> Now there is a line in the beagle.conf that says:
> #includeifexists custom/usbradio.conf
>  
> However, as you see it is commented out.
>  
> Should those two lines have an effect out of beagle.conf or do I need to add usbradio.conf and remove the uncomment #?
>  
> Thanks,
> Mike
> Kb8zgl
>  
>  
>  
> From: Ken [mailto:ke2n at cs.com] 
> Sent: Sunday, September 16, 2012 12:15 PM
> To: 'Mike Wolthuis'; app_rpt-users at ohnosec.org
> Subject: RE: [App_rpt-users] TX Tone Drop out Time
>  
> Beagle board uses chan_simpleusb
>  
> So the config file is:  simpleusb.conf
>  
> Allegedly it supports the same encoding functions.
> See:
> http://ohnosec.org/pipermail/app_rpt-users/2011-February/002275.html
>  
> Ken
>  
>  
>  
> From: app_rpt-users-bounces at ohnosec.org [mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of Mike Wolthuis
> Sent: Sunday, September 16, 2012 9:52 AM
> To: app_rpt-users at ohnosec.org
> Subject: Re: [App_rpt-users] TX Tone Drop out Time
>  
> Does this work on a Beagle board also do you know?
>  
> Mike
> Kb8zgl
>  
> From: app_rpt-users-bounces at ohnosec.org [mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of Ken
> Sent: Sunday, September 16, 2012 7:55 AM
> To: 'Jim W7RY'; app_rpt-users at ohnosec.org
> Subject: Re: [App_rpt-users] TX Tone Drop out Time
>  
> This is in usbradio.conf
>  
> txtoctype=notone     ; Transmit tone control type: no,phase,notone
>                      ; no - CTCSS tone encoding with no hang time
>                      ; phase - encode CTCSS and reverse phase
>                      ; AKA ("reverse burst") before unkeying TX
>                      ; notone - encode CTCSS and stop sending tone before unkeying TX
>                      ; AKA ("chicken burst")
>  
>  
> If you select notone (as shown here), then the PL drops about 600 ms before the carrier drops.
> Most people like it that way ;-)
>  
> Ken
>  
>  
> From: app_rpt-users-bounces at ohnosec.org [mailto:app_rpt-users-bounces at ohnosec.org] On Behalf Of Jim W7RY
> Sent: Sunday, September 16, 2012 12:05 AM
> To: app_rpt-users at ohnosec.org
> Subject: [App_rpt-users] TX Tone Drop out Time
>  
> I had my PL tone encoder (node generated) drop out before the carrier dropped out. It seems to have quit working. The PL generator is working fine, but the timing seems to changed.  I don’t seem to find the command now. I'm probably not be looking in the right file.
>  
> Can someone please tell me where that setting is?
>  
> Thanks!
> 73
> Jim W7RY
>  
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at ohnosec.org
> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20120917/eba22497/attachment.html>