[App_rpt-users] Total list of all Allstar commands
Nate Hardman
nhardman1428 at gmail.com
Fri Jan 5 14:06:38 UTC 2018
in rpt.conf, (cut and paste ) the [functions] stanza to a seperate file
labeled commands.include then delete or comment out all the commands in the
stanza and replace with this line "#include commands.include" THEN put
all the commands YOU want above and beyond what is required to be standard
across everyones nodes 1-5 ilink etc. in the commands.include file. Use
(winSCP) to copy the commands.include file to all your nodes and edit each
nodes rpt.conf stanza to have the line in [functions] be #include
commands.include. For each new system you just you build just add YOUR
commands.include file and it will have all the same commands as the
others.
from my rpt.conf
..........
outstreamcmd=/bin/sh,-c,/usr/bin/lame --preset cbr 16 -r -m m -s 8
--bitwidth 16 - - 2> /tmp/stream.status | /usr/bin/ezstream -qvc
/etc/ezstream.xml
[functions]
#include commands.include
#include /etc/asterisk/local/localcmds.include
[morse]
speed=20
............................
and a copy of a generic commands.include file for you to cut and paste if
you wish.
root at N8THN:/etc/asterisk# cat commands.include
;commands.include
;Command common acrossed all nodes
;single digit public commands
0=autopatchdn
1=ilink,1 ; Disconnect Link
2=ilink,2 ; Connect Link MOnitor Only
3=ilink,3 ; Connect Link Transieve
4=ilink,4 ; Enter Command Mode on another Node
5=macro,1 ; Macro Prefix
6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 ; Autopatch up
;double digit public commands
70=ilink,5 ; System Status
71=ilink,6 ; Disconnect all Links
72=ilink,7 ; Play Last Node to Key Up
73=ilink,15 ; FULL system Status - all nodes
74=ilink,16 ; Reconnect disconnected links disconnected with disconnect all
links command
75=ilink,8 ; Connect Link LOCAL monitor only
76=
77=
78=
79=
80=status,11 ;Force ID LOCAL ONLY
81=status,12 ; GIve Time of Day LOCAL ONLY
82=status,3 ; Give Software Verison
83=status,5 ; Last DTMF User
84=cop,32 ; DTMF TEST
85=
86=
87=
88=cop,55 ;Parrot Once if parrot mode is disabled
89=autopatchup,context=command_process,noct=1,farenddisconnect=1,dialtime=7000,quiet=1;
Command Processing
99=cop,6 ; ptt phone mode
; Triple digit control operator /owner codes
900=cop,3 ;disable system
901=cop,2 ;enable system
903=cop,1 ;System warm boot
902=
903=
904=cop,4 ;Test Tone On/Off
905=cop,5 ;dump system variables
906=
907=cop,7 ;Time out timer enable
908=cop,8 ;Time out timer disable
909=cop,9 ;Autopatch enable
910=cop,10 ;Autopatch disable
911=cop,11 ;Link enable
912=cop,12 ;Link disable
913=cop,13 ;Query System State
914=cop,14 ;Change System State
915=cop,15 ;Scheduler Enable
916=cop,16 ;Scheduler Disable
917=cop,17 ;User functions (time, id, etc) enable
918=cop,18 ;User functions (time, id, etc) disable
919=cop,19 ;Select alternate hang timer
920=cop,20 ;Select standard hang timer
921=cop,21 ;Enable Parrot Mode
922=cop,22 ;Disable Parrot Mode
923=cop,23 ;Birdbath (Current Parrot Cleanup/Flush)
924=cop,24 ;Flush all telemetry
925=cop,25 ;Query !!!!last node un-keyed!!!!
926=cop,26 ;Query all nodes keyed/unkeyed
927=cop,27 ;Reset DAQ minimum on a pin
928=cop,28 ;Reset DAQ maximum on a pin
929=
930=cop,30 ;Recall Memory Setting in Attached Xcvr
931=cop,31 ;Channel Selector for Parallel Programmed Xcvr
932=
933=cop,33 ;Local Telemetry Output Enable
934=cop,34 ;Local Telemetry Output Disable
935=cop,35 ;Local Telemetry Output on Demand
936=cop,36 ;Foreign Link Local Output Path Enable
937=cop,37 ;Foreign Link Local Output Path Disable
938=cop,38 ;Foreign Link Local Output Path Follows Local Telemetry
939=cop,39 ;Foreign Link Local Output Path on Demand
940=cop,40 ;IRLP announce Enable
941=cop,41 ;IRLP announce Disable
942=cop,42 ;Echolink announce node # only
943=cop,43 ;Echolink announce node Callsign only
944=cop,44 ;Echolink announce node # & Callsign
945=cop,45 ;Link Activity timer enable
946=cop,46 ;Link Activity timer disable
947=cop,47 ;Reset "Link Config Changed" Flag
948=cop,48 ;Send Page-Tone specs separated by ( )
949=cop,49 ;Disable incoming connections (control state NOICE)
950=cop,50 ;Enable incoming connections (control state NOICD)
951=cop,51 ;Enable sleep mode
952=cop,52 ;Disable sleep mode
953=cop,53 ;Wake up from sleep
954=cop,54 ;Go to sleep
955=cop,60 ;SEND MDC-1200 Burst
956=cop,56 ;Rx CTCSS Enable
957=cop,57 ;Rx CTCSS Disable
958=cop,58 ;Tx CTCSS On Input only Enable
959=cop,59 ;Tx CTCSS On Input only Disable
; 98 series up to local nodes
On Fri, Jan 5, 2018 at 3:31 AM, larry <larry at n7fm.com> wrote:
> Can some one point me to a listing of every available command defined that
> can used with Allstar.
>
> I am have a heck of a time trying to configure my nodes so everything is
> all the same commands on all my nodes..
> It seems whenever there is a different version other than the 1-5 ilink
> commands there is no standard numbering system between versions or
> platforms.
> Realizing that it is up to me to standardize my own system I am about to
> start from scratch eliminating all the jumble.
> It would certainly be helpful if there was a COMPLETE command list with
> explanations of their functions.
>
> Larry - N7FM
> _______________________________________________
> App_rpt-users mailing list
> App_rpt-users at lists.allstarlink.org
> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
>
> To unsubscribe from this list please visit http://lists.allstarlink.org/c
> gi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of
> the page. Enter your email address and press the "Unsubscribe or edit
> options button"
> You do not need a password to unsubscribe, you can do it via email
> confirmation. If you have trouble unsubscribing, please send a message to
> the list detailing the problem.
--
Nathan Hardman
nhardman1428 at gmail.com
N8THN at ARRL.NET
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.keekles.org/pipermail/app_rpt-users/attachments/20180105/cd1f4005/attachment.html>
More information about the App_rpt-users
mailing list