Could someone help me with getting allstar link up and running. I just can't allstar configured correctly to the point where I can tune the radios. I just don't understand what I am doing wrong.
Well, I am not sure what you are using for hardware and what versions of software as you did not say. SO here is my advise for anyone. Make the box work 'headless', meaning without the radios in the setup fray. Use this setting by un/commenting the following lines as shown here in your rpt.cong file so you are using dahdi/pseudo and not radio interfaces. rxchannel = dahdi/pseudo ; No radio (hub) ****************** ; rxchannel = SimpleUSB/usb_29999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_29999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard ; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP duplex = 2 ; 0 = Half duplex with no telemetry tones or hang time. Then setup iaxrpt to run with that node so you can check it for functionality of a running asterisk install without the radio side of the equation. You will have to read some more of the docs most likely to get this far, but once you do, you are most of the way there. You should be able to 'command' your node with functionality before adding radios to your learning curve. But you will need to ask 'specific questions' to what you do not understand to get help. ...mike/kb8jnm On 6/25/2018 9:38 PM, Dale Day wrote:
Could someone help me with getting allstar link up and running. I just can't allstar configured correctly to the point where I can tune the radios. I just don't understand what I am doing wrong.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Thank you so much for your reply. I have the latest download of Debian from Allstar link. I have it installed on a amd desk top pc and then it linked to pm windows pc with putty. I have a dmk engineering usb radio interface to a Motorola gm300 type radio. I understand this is very difficult to do over email but I have worked on this off and on for two years and I am just at wits end. I go through the asl-menu and have it configured the static ip address and have signed up with Allstar and have my numbers and passwords with server and my pc. My problem is when I try to go to tune radio menu it comes up with a message that I don't have rpt file and another one I cant remember with out going and firing up pc again and refreshing my memory not configured. So in other words I just don't know which of the hundreds of lines in the files usb radio, simpleusb or other files need to be modified. I will keep reading the help files and and k5tra's web site but I just can't seem to get the files configured right. Thanks so much Dale N0INX On Mon, Jun 25, 2018 at 11:58 PM, Mike <mm@midnighteng.com> wrote:
Well,
I am not sure what you are using for hardware and what versions of software as you did not say.
SO here is my advise for anyone.
Make the box work 'headless', meaning without the radios in the setup fray.
Use this setting by un/commenting the following lines as shown here in your rpt.cong file so you are using dahdi/pseudo and not radio interfaces.
rxchannel = dahdi/pseudo ; No radio (hub) ****************** ; rxchannel = SimpleUSB/usb_29999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_29999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard ; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
duplex = 2 ; 0 = Half duplex with no telemetry tones or hang time.
Then setup iaxrpt to run with that node so you can check it for functionality of a running asterisk install without the radio side of the equation.
You will have to read some more of the docs most likely to get this far, but once you do, you are most of the way there.
You should be able to 'command' your node with functionality before adding radios to your learning curve.
But you will need to ask 'specific questions' to what you do not understand to get help.
...mike/kb8jnm
On 6/25/2018 9:38 PM, Dale Day wrote:
Could someone help me with getting allstar link up and running. I just can't allstar configured correctly to the point where I can tune the radios. I just don't understand what I am doing wrong.
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
While I have 'NO' experience with the DMK interface, I still suggest you try to make this run 'headless' first. Then you can separate core issues of the system with the radio interface side of it. If the system isn't functioning as it should, you will never know if the radio's are. I am hoping someone with experience with the DMK will chime in but you need to specify a issue to respond to, specifically. Show the code you are having issues with etc. Give us a starting point. Most here are very helpful, give them a chance. ...mike/kb8jnm On 6/26/2018 10:08 AM, Dale Day wrote:
Thank you so much for your reply. I have the latest download of Debian from Allstar link. I have it installed on a amd desk top pc and then it linked to pm windows pc with putty. I have a dmk engineering usb radio interface to a Motorola gm300 type radio. I understand this is very difficult to do over email but I have worked on this off and on for two years and I am just at wits end. I go through the asl-menu and have it configured the static ip address and have signed up with Allstar and have my numbers and passwords with server and my pc. My problem is when I try to go to tune radio menu it comes up with a message that I don't have rpt file and another one I cant remember with out going and firing up pc again and refreshing my memory not configured. So in other words I just don't know which of the hundreds of lines in the files usb radio, simpleusb or other files need to be modified. I will keep reading the help files and and k5tra's web site but I just can't seem to get the files configured right. Thanks so much Dale N0INX
On Mon, Jun 25, 2018 at 11:58 PM, Mike <mm@midnighteng.com <mailto:mm@midnighteng.com>> wrote:
Well,
I am not sure what you are using for hardware and what versions of software as you did not say.
SO here is my advise for anyone.
Make the box work 'headless', meaning without the radios in the setup fray.
Use this setting by un/commenting the following lines as shown here in your rpt.cong file so you are using dahdi/pseudo and not radio interfaces.
rxchannel = dahdi/pseudo ; No radio (hub) ****************** ; rxchannel = SimpleUSB/usb_29999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_29999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard ; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
duplex = 2 ; 0 = Half duplex with no telemetry tones or hang time.
Then setup iaxrpt to run with that node so you can check it for functionality of a running asterisk install without the radio side of the equation.
You will have to read some more of the docs most likely to get this far, but once you do, you are most of the way there.
You should be able to 'command' your node with functionality before adding radios to your learning curve.
But you will need to ask 'specific questions' to what you do not understand to get help.
...mike/kb8jnm
On 6/25/2018 9:38 PM, Dale Day wrote:
Could someone help me with getting allstar link up and running. I just can't allstar configured correctly to the point where I can tune the radios. I just don't understand what I am doing wrong.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
To unsubscribe from this list please visithttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users>
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users <http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Hello Dale, Login and run "sudo asl-menu" GM300 Programmed with Pl. Use Simple-USB-Radio Not programmed with PL. I would use USB-Radio. Save and reboot. I'll post the tune tonight. David On Tue, Jun 26, 2018, 7:47 AM Mike <mm@midnighteng.com> wrote:
While I have 'NO' experience with the DMK interface,
I still suggest you try to make this run 'headless' first.
Then you can separate core issues of the system with the radio interface side of it.
If the system isn't functioning as it should, you will never know if the radio's are.
I am hoping someone with experience with the DMK will chime in but you need to specify a issue to respond to, specifically.
Show the code you are having issues with etc.
Give us a starting point. Most here are very helpful, give them a chance.
...mike/kb8jnm
On 6/26/2018 10:08 AM, Dale Day wrote:
Thank you so much for your reply. I have the latest download of Debian from Allstar link. I have it installed on a amd desk top pc and then it linked to pm windows pc with putty. I have a dmk engineering usb radio interface to a Motorola gm300 type radio. I understand this is very difficult to do over email but I have worked on this off and on for two years and I am just at wits end. I go through the asl-menu and have it configured the static ip address and have signed up with Allstar and have my numbers and passwords with server and my pc. My problem is when I try to go to tune radio menu it comes up with a message that I don't have rpt file and another one I cant remember with out going and firing up pc again and refreshing my memory not configured. So in other words I just don't know which of the hundreds of lines in the files usb radio, simpleusb or other files need to be modified. I will keep reading the help files and and k5tra's web site but I just can't seem to get the files configured right. Thanks so much Dale N0INX
On Mon, Jun 25, 2018 at 11:58 PM, Mike <mm@midnighteng.com> wrote:
Well,
I am not sure what you are using for hardware and what versions of software as you did not say.
SO here is my advise for anyone.
Make the box work 'headless', meaning without the radios in the setup fray.
Use this setting by un/commenting the following lines as shown here in your rpt.cong file so you are using dahdi/pseudo and not radio interfaces.
rxchannel = dahdi/pseudo ; No radio (hub) ****************** ; rxchannel = SimpleUSB/usb_29999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_29999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard ; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
duplex = 2 ; 0 = Half duplex with no telemetry tones or hang time.
Then setup iaxrpt to run with that node so you can check it for functionality of a running asterisk install without the radio side of the equation.
You will have to read some more of the docs most likely to get this far, but once you do, you are most of the way there.
You should be able to 'command' your node with functionality before adding radios to your learning curve.
But you will need to ask 'specific questions' to what you do not understand to get help.
...mike/kb8jnm
On 6/25/2018 9:38 PM, Dale Day wrote:
Could someone help me with getting allstar link up and running. I just can't allstar configured correctly to the point where I can tune the radios. I just don't understand what I am doing wrong.
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Hello Dale, Are you using simpleusb or usbradio? David -- Thanks, David "Laws that forbid the carrying of arms...disarm only those who are neither inclined nor determined to commit crimes. Such laws make things worse for the assaulted and better for the assailants; they serve rather to encourage than prevent homicides, for an unarmed man may be attacked with greater confidence than an armed one." Thomas Jefferson On Tue, Jun 26, 2018 at 8:02 AM, David Shaw <shawpbx@gmail.com> wrote:
Hello Dale,
Login and run "sudo asl-menu"
GM300 Programmed with Pl. Use Simple-USB-Radio
Not programmed with PL. I would use USB-Radio.
Save and reboot.
I'll post the tune tonight.
David
On Tue, Jun 26, 2018, 7:47 AM Mike <mm@midnighteng.com> wrote:
While I have 'NO' experience with the DMK interface,
I still suggest you try to make this run 'headless' first.
Then you can separate core issues of the system with the radio interface side of it.
If the system isn't functioning as it should, you will never know if the radio's are.
I am hoping someone with experience with the DMK will chime in but you need to specify a issue to respond to, specifically.
Show the code you are having issues with etc.
Give us a starting point. Most here are very helpful, give them a chance.
...mike/kb8jnm
On 6/26/2018 10:08 AM, Dale Day wrote:
Thank you so much for your reply. I have the latest download of Debian from Allstar link. I have it installed on a amd desk top pc and then it linked to pm windows pc with putty. I have a dmk engineering usb radio interface to a Motorola gm300 type radio. I understand this is very difficult to do over email but I have worked on this off and on for two years and I am just at wits end. I go through the asl-menu and have it configured the static ip address and have signed up with Allstar and have my numbers and passwords with server and my pc. My problem is when I try to go to tune radio menu it comes up with a message that I don't have rpt file and another one I cant remember with out going and firing up pc again and refreshing my memory not configured. So in other words I just don't know which of the hundreds of lines in the files usb radio, simpleusb or other files need to be modified. I will keep reading the help files and and k5tra's web site but I just can't seem to get the files configured right. Thanks so much Dale N0INX
On Mon, Jun 25, 2018 at 11:58 PM, Mike <mm@midnighteng.com> wrote:
Well,
I am not sure what you are using for hardware and what versions of software as you did not say.
SO here is my advise for anyone.
Make the box work 'headless', meaning without the radios in the setup fray.
Use this setting by un/commenting the following lines as shown here in your rpt.cong file so you are using dahdi/pseudo and not radio interfaces.
rxchannel = dahdi/pseudo ; No radio (hub) ****************** ; rxchannel = SimpleUSB/usb_29999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_29999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard ; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
duplex = 2 ; 0 = Half duplex with no telemetry tones or hang time.
Then setup iaxrpt to run with that node so you can check it for functionality of a running asterisk install without the radio side of the equation.
You will have to read some more of the docs most likely to get this far, but once you do, you are most of the way there.
You should be able to 'command' your node with functionality before adding radios to your learning curve.
But you will need to ask 'specific questions' to what you do not understand to get help.
...mike/kb8jnm
On 6/25/2018 9:38 PM, Dale Day wrote:
Could someone help me with getting allstar link up and running. I just can't allstar configured correctly to the point where I can tune the radios. I just don't understand what I am doing wrong.
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/ cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
I'm sorry I have been really busy to work on allstar so when I get a chance i will try what you guys suggest Thanks for all your help On Tue, Jun 26, 2018, 9:16 PM David Shaw <shawpbx@gmail.com> wrote:
Hello Dale,
Are you using simpleusb or usbradio?
David
-- Thanks, David
"Laws that forbid the carrying of arms...disarm only those who are neither inclined nor determined to commit crimes. Such laws make things worse for the assaulted and better for the assailants; they serve rather to encourage than prevent homicides, for an unarmed man may be attacked with greater confidence than an armed one." Thomas Jefferson
On Tue, Jun 26, 2018 at 8:02 AM, David Shaw <shawpbx@gmail.com> wrote:
Hello Dale,
Login and run "sudo asl-menu"
GM300 Programmed with Pl. Use Simple-USB-Radio
Not programmed with PL. I would use USB-Radio.
Save and reboot.
I'll post the tune tonight.
David
On Tue, Jun 26, 2018, 7:47 AM Mike <mm@midnighteng.com> wrote:
While I have 'NO' experience with the DMK interface,
I still suggest you try to make this run 'headless' first.
Then you can separate core issues of the system with the radio interface side of it.
If the system isn't functioning as it should, you will never know if the radio's are.
I am hoping someone with experience with the DMK will chime in but you need to specify a issue to respond to, specifically.
Show the code you are having issues with etc.
Give us a starting point. Most here are very helpful, give them a chance.
...mike/kb8jnm
On 6/26/2018 10:08 AM, Dale Day wrote:
Thank you so much for your reply. I have the latest download of Debian from Allstar link. I have it installed on a amd desk top pc and then it linked to pm windows pc with putty. I have a dmk engineering usb radio interface to a Motorola gm300 type radio. I understand this is very difficult to do over email but I have worked on this off and on for two years and I am just at wits end. I go through the asl-menu and have it configured the static ip address and have signed up with Allstar and have my numbers and passwords with server and my pc. My problem is when I try to go to tune radio menu it comes up with a message that I don't have rpt file and another one I cant remember with out going and firing up pc again and refreshing my memory not configured. So in other words I just don't know which of the hundreds of lines in the files usb radio, simpleusb or other files need to be modified. I will keep reading the help files and and k5tra's web site but I just can't seem to get the files configured right. Thanks so much Dale N0INX
On Mon, Jun 25, 2018 at 11:58 PM, Mike <mm@midnighteng.com> wrote:
Well,
I am not sure what you are using for hardware and what versions of software as you did not say.
SO here is my advise for anyone.
Make the box work 'headless', meaning without the radios in the setup fray.
Use this setting by un/commenting the following lines as shown here in your rpt.cong file so you are using dahdi/pseudo and not radio interfaces.
rxchannel = dahdi/pseudo ; No radio (hub) ****************** ; rxchannel = SimpleUSB/usb_29999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_29999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard ; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
duplex = 2 ; 0 = Half duplex with no telemetry tones or hang time.
Then setup iaxrpt to run with that node so you can check it for functionality of a running asterisk install without the radio side of the equation.
You will have to read some more of the docs most likely to get this far, but once you do, you are most of the way there.
You should be able to 'command' your node with functionality before adding radios to your learning curve.
But you will need to ask 'specific questions' to what you do not understand to get help.
...mike/kb8jnm
On 6/25/2018 9:38 PM, Dale Day wrote:
Could someone help me with getting allstar link up and running. I just can't allstar configured correctly to the point where I can tune the radios. I just don't understand what I am doing wrong.
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
I'm sorry I don't know what simple USB is I have a dmk engineering USB device hooked up to a Motorola mobile On Tue, Jun 26, 2018, 9:16 PM David Shaw <shawpbx@gmail.com> wrote:
Hello Dale,
Are you using simpleusb or usbradio?
David
-- Thanks, David
"Laws that forbid the carrying of arms...disarm only those who are neither inclined nor determined to commit crimes. Such laws make things worse for the assaulted and better for the assailants; they serve rather to encourage than prevent homicides, for an unarmed man may be attacked with greater confidence than an armed one." Thomas Jefferson
On Tue, Jun 26, 2018 at 8:02 AM, David Shaw <shawpbx@gmail.com> wrote:
Hello Dale,
Login and run "sudo asl-menu"
GM300 Programmed with Pl. Use Simple-USB-Radio
Not programmed with PL. I would use USB-Radio.
Save and reboot.
I'll post the tune tonight.
David
On Tue, Jun 26, 2018, 7:47 AM Mike <mm@midnighteng.com> wrote:
While I have 'NO' experience with the DMK interface,
I still suggest you try to make this run 'headless' first.
Then you can separate core issues of the system with the radio interface side of it.
If the system isn't functioning as it should, you will never know if the radio's are.
I am hoping someone with experience with the DMK will chime in but you need to specify a issue to respond to, specifically.
Show the code you are having issues with etc.
Give us a starting point. Most here are very helpful, give them a chance.
...mike/kb8jnm
On 6/26/2018 10:08 AM, Dale Day wrote:
Thank you so much for your reply. I have the latest download of Debian from Allstar link. I have it installed on a amd desk top pc and then it linked to pm windows pc with putty. I have a dmk engineering usb radio interface to a Motorola gm300 type radio. I understand this is very difficult to do over email but I have worked on this off and on for two years and I am just at wits end. I go through the asl-menu and have it configured the static ip address and have signed up with Allstar and have my numbers and passwords with server and my pc. My problem is when I try to go to tune radio menu it comes up with a message that I don't have rpt file and another one I cant remember with out going and firing up pc again and refreshing my memory not configured. So in other words I just don't know which of the hundreds of lines in the files usb radio, simpleusb or other files need to be modified. I will keep reading the help files and and k5tra's web site but I just can't seem to get the files configured right. Thanks so much Dale N0INX
On Mon, Jun 25, 2018 at 11:58 PM, Mike <mm@midnighteng.com> wrote:
Well,
I am not sure what you are using for hardware and what versions of software as you did not say.
SO here is my advise for anyone.
Make the box work 'headless', meaning without the radios in the setup fray.
Use this setting by un/commenting the following lines as shown here in your rpt.cong file so you are using dahdi/pseudo and not radio interfaces.
rxchannel = dahdi/pseudo ; No radio (hub) ****************** ; rxchannel = SimpleUSB/usb_29999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_29999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard ; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
duplex = 2 ; 0 = Half duplex with no telemetry tones or hang time.
Then setup iaxrpt to run with that node so you can check it for functionality of a running asterisk install without the radio side of the equation.
You will have to read some more of the docs most likely to get this far, but once you do, you are most of the way there.
You should be able to 'command' your node with functionality before adding radios to your learning curve.
But you will need to ask 'specific questions' to what you do not understand to get help.
...mike/kb8jnm
On 6/25/2018 9:38 PM, Dale Day wrote:
Could someone help me with getting allstar link up and running. I just can't allstar configured correctly to the point where I can tune the radios. I just don't understand what I am doing wrong.
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing listApp_rpt-users@lists.allstarlink.orghttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
I am of little help to you but I did find this on the web, perhaps it helps, http://www.dmkeng.com/images/URI-FAQs.pdf But I might add that DMK supports their product and know-how, you should consult their library for instructions. Generally, if you are using the radio for PL/CTCSS signalling and not the DSP in asterisk/app_rpt, it would be a simpleusb install but if not, you would need the extended services of radiousb. ...mike/kb8jnm On 6/28/2018 10:02 AM, Dale Day wrote:
I'm sorry I don't know what simple USB is I have a dmk engineering USB device hooked up to a Motorola mobile
On Tue, Jun 26, 2018, 9:16 PM David Shaw <shawpbx@gmail.com <mailto:shawpbx@gmail.com>> wrote:
Hello Dale,
Are you using simpleusb or usbradio?
David
-- Thanks, David
"Laws that forbid the carrying of arms...disarm only those who are neither inclined nor determined to commit crimes. Such laws make things worse for the assaulted and better for the assailants; they serve rather to encourage than prevent homicides, for an unarmed man may be attacked with greater confidence than an armed one." Thomas Jefferson
On Tue, Jun 26, 2018 at 8:02 AM, David Shaw <shawpbx@gmail.com <mailto:shawpbx@gmail.com>> wrote:
Hello Dale,
Login and run "sudo asl-menu"
GM300 Programmed with Pl. Use Simple-USB-Radio
Not programmed with PL. I would use USB-Radio.
Save and reboot. I'll post the tune tonight.
David
On Tue, Jun 26, 2018, 7:47 AM Mike <mm@midnighteng.com <mailto:mm@midnighteng.com>> wrote:
While I have 'NO' experience with the DMK interface,
I still suggest you try to make this run 'headless' first.
Then you can separate core issues of the system with the radio interface side of it.
If the system isn't functioning as it should, you will never know if the radio's are.
I am hoping someone with experience with the DMK will chime in but you need to specify a issue to respond to, specifically.
Show the code you are having issues with etc.
Give us a starting point. Most here are very helpful, give them a chance.
...mike/kb8jnm
On 6/26/2018 10:08 AM, Dale Day wrote:
Thank you so much for your reply. I have the latest download of Debian from Allstar link. I have it installed on a amd desk top pc and then it linked to pm windows pc with putty. I have a dmk engineering usb radio interface to a Motorola gm300 type radio. I understand this is very difficult to do over email but I have worked on this off and on for two years and I am just at wits end. I go through the asl-menu and have it configured the static ip address and have signed up with Allstar and have my numbers and passwords with server and my pc. My problem is when I try to go to tune radio menu it comes up with a message that I don't have rpt file and another one I cant remember with out going and firing up pc again and refreshing my memory not configured. So in other words I just don't know which of the hundreds of lines in the files usb radio, simpleusb or other files need to be modified. I will keep reading the help files and and k5tra's web site but I just can't seem to get the files configured right. Thanks so much Dale N0INX
On Mon, Jun 25, 2018 at 11:58 PM, Mike <mm@midnighteng.com <mailto:mm@midnighteng.com>> wrote:
Well,
I am not sure what you are using for hardware and what versions of software as you did not say.
SO here is my advise for anyone.
Make the box work 'headless', meaning without the radios in the setup fray.
Use this setting by un/commenting the following lines as shown here in your rpt.cong file so you are using dahdi/pseudo and not radio interfaces.
rxchannel = dahdi/pseudo ; No radio (hub) ****************** ; rxchannel = SimpleUSB/usb_29999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_29999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard ; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
duplex = 2 ; 0 = Half duplex with no telemetry tones or hang time.
Then setup iaxrpt to run with that node so you can check it for functionality of a running asterisk install without the radio side of the equation.
You will have to read some more of the docs most likely to get this far, but once you do, you are most of the way there.
You should be able to 'command' your node with functionality before adding radios to your learning curve.
But you will need to ask 'specific questions' to what you do not understand to get help.
...mike/kb8jnm
On 6/25/2018 9:38 PM, Dale Day wrote:
Could someone help me with getting allstar link up and running. I just can't allstar configured correctly to the point where I can tune the radios. I just don't understand what I am doing wrong.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visithttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visithttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Dale. When you used ASL-menu to create your node, did you select USBRADIO, SIMPLEUSB. DAHDI/PSEUDO. For the INTERFACE type? Sent from my iPhone
On Jun 28, 2018, at 11:23 AM, Mike <mm@midnighteng.com> wrote:
I am of little help to you but I did find this on the web, perhaps it helps,
http://www.dmkeng.com/images/URI-FAQs.pdf
But I might add that DMK supports their product and know-how, you should consult their library for instructions.
Generally, if you are using the radio for PL/CTCSS signalling and not the DSP in asterisk/app_rpt, it would be a simpleusb install
but if not, you would need the extended services of radiousb.
...mike/kb8jnm
On 6/28/2018 10:02 AM, Dale Day wrote: I'm sorry I don't know what simple USB is I have a dmk engineering USB device hooked up to a Motorola mobile
On Tue, Jun 26, 2018, 9:16 PM David Shaw <shawpbx@gmail.com> wrote: Hello Dale,
Are you using simpleusb or usbradio?
David
-- Thanks, David
"Laws that forbid the carrying of arms...disarm only those who are neither inclined nor determined to commit crimes. Such laws make things worse for the assaulted and better for the assailants; they serve rather to encourage than prevent homicides, for an unarmed man may be attacked with greater confidence than an armed one." Thomas Jefferson
On Tue, Jun 26, 2018 at 8:02 AM, David Shaw <shawpbx@gmail.com> wrote: Hello Dale,
Login and run "sudo asl-menu"
GM300 Programmed with Pl. Use Simple-USB-Radio
Not programmed with PL. I would use USB-Radio.
Save and reboot.
I'll post the tune tonight.
David
On Tue, Jun 26, 2018, 7:47 AM Mike <mm@midnighteng.com> wrote: While I have 'NO' experience with the DMK interface,
I still suggest you try to make this run 'headless' first.
Then you can separate core issues of the system with the radio interface side of it.
If the system isn't functioning as it should, you will never know if the radio's are. I am hoping someone with experience with the DMK will chime in but you need to specify a issue to respond to, specifically.
Show the code you are having issues with etc. Give us a starting point. Most here are very helpful, give them a chance. ...mike/kb8jnm
On 6/26/2018 10:08 AM, Dale Day wrote: Thank you so much for your reply. I have the latest download of Debian from Allstar link. I have it installed on a amd desk top pc and then it linked to pm windows pc with putty. I have a dmk engineering usb radio interface to a Motorola gm300 type radio. I understand this is very difficult to do over email but I have worked on this off and on for two years and I am just at wits end. I go through the asl-menu and have it configured the static ip address and have signed up with Allstar and have my numbers and passwords with server and my pc. My problem is when I try to go to tune radio menu it comes up with a message that I don't have rpt file and another one I cant remember with out going and firing up pc again and refreshing my memory not configured. So in other words I just don't know which of the hundreds of lines in the files usb radio, simpleusb or other files need to be modified. I will keep reading the help files and and k5tra's web site but I just can't seem to get the files configured right. Thanks so much Dale N0INX
On Mon, Jun 25, 2018 at 11:58 PM, Mike <mm@midnighteng.com> wrote: Well,
I am not sure what you are using for hardware and what versions of software as you did not say.
SO here is my advise for anyone.
Make the box work 'headless', meaning without the radios in the setup fray.
Use this setting by un/commenting the following lines as shown here in your rpt.cong file so you are using dahdi/pseudo and not radio interfaces. rxchannel = dahdi/pseudo ; No radio (hub) ****************** ; rxchannel = SimpleUSB/usb_29999 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_29999 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard ; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
duplex = 2 ; 0 = Half duplex with no telemetry tones or hang time.
Then setup iaxrpt to run with that node so you can check it for functionality of a running asterisk install without the radio side of the equation.
You will have to read some more of the docs most likely to get this far, but once you do, you are most of the way there.
You should be able to 'command' your node with functionality before adding radios to your learning curve.
But you will need to ask 'specific questions' to what you do not understand to get help.
...mike/kb8jnm
On 6/25/2018 9:38 PM, Dale Day wrote:
Could someone help me with getting allstar link up and running. I just can't allstar configured correctly to the point where I can tune the radios. I just don't understand what I am doing wrong.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
participants (4)
-
Dale Day -
David Shaw -
Mike -
nhardman1428＠gmail.com