New DIAL Install No RX or TX Audio from URI
I had my node working under ACID till a hard drive decided to crash on me. I did the re-install with the 32 bit DIAL install. Everything about the node appears to function properly but from asterisk to my URI I get ZERO audio in or out. It's the only audio adapter, and the URIDIAG with the loopback plug tests fine. It will activate the TX and I get the blinking green led but no audio in or out. Is there somewhere I can look to troubleshoot this issue? The motherboard is an older atom 330 board. Should I fall back to the older ACID install for this node which had worked. Thanks for any guidance that you can provide.Keith Dobbins N8KLD
Which channel driver are you using? Anything in the log? 73, Steve N4IRS On 12/26/2017 11:30 AM, Keith Dobbins wrote:
I had my node working under ACID till a hard drive decided to crash on me. I did the re-install with the 32 bit DIAL install. Everything about the node appears to function properly but from asterisk to my URI I get ZERO audio in or out. It's the only audio adapter, and the URIDIAG with the loopback plug tests fine. It will activate the TX and I get the blinking green led but no audio in or out. Is there somewhere I can look to troubleshoot this issue? The motherboard is an older atom 330 board. Should I fall back to the older ACID install for this node which had worked.
Thanks for any guidance that you can provide. Keith Dobbins N8KLD
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
I tried both Chan USB and Simple USB with both having the same. I'll double check the log files but didn't see anything in there when I checked. Keith DobbinsSr. IT Systems EngineerManaged File Transfer/Mainframe Networks3402 Linden Street Parkersburg, WV 26104-1608 Amateur Radio Call Sign: N8KLD On Tuesday, December 26, 2017, 11:40:18 AM EST, Steve Zingman <szingman@msgstor.com> wrote: Which channel driver are you using? Anything in the log? 73, Steve N4IRS On 12/26/2017 11:30 AM, Keith Dobbins wrote: I had my node working under ACID till a hard drive decided to crash on me. I did the re-install with the 32 bit DIAL install. Everything about the node appears to function properly but from asterisk to my URI I get ZERO audio in or out. It's the only audio adapter, and the URIDIAG with the loopback plug tests fine. It will activate the TX and I get the blinking green led but no audio in or out. Is there somewhere I can look to troubleshoot this issue? The motherboard is an older atom 330 board. Should I fall back to the older ACID install for this node which had worked. Thanks for any guidance that you can provide. Keith Dobbins N8KLD _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
This is in the messages log after a reboot now: [Dec 26 00:06:21] WARNING[941] channel.c: Channel allocation failed: Refusing due to active shutdown[Dec 26 00:06:21] WARNING[941] chan_simpleusb.c: Unable to create new usb channel[Dec 26 00:06:21] NOTICE[944] dnsmgr.c: Managed DNS entries will be refreshed every 300 seconds.[Dec 26 00:06:21] NOTICE[944] cdr.c: CDR simple logging enabled.[Dec 26 00:06:21] NOTICE[944] loader.c: 54 modules will be loaded.[Dec 26 00:06:21] WARNING[944] acl.c: is not a valid IP[Dec 26 00:06:21] WARNING[944] chan_simpleusb.c: File simpleusb_tune_usb45467.conf not found, using default parameters.[Dec 26 00:06:21] NOTICE[961] app_rpt.c: Normal Repeater Init 45467[Dec 26 00:06:22] NOTICE[982] chan_simpleusb.c: Assigned USB device 3-2:1.0 to simpleusb channel usb45467[Dec 26 00:06:22] WARNING[982] chan_simpleusb.c: File simpleusb_tune_usb45467.conf not found, device usb45467 using default parameters.[Dec 26 00:06:22] WARNING[981] chan_simpleusb.c: Possibly stuck USB read channel. [usb45467][Dec 26 00:06:22] WARNING[981] chan_simpleusb.c: Nope, USB read channel [usb45467] wasn't stuck after all. the simpleusb_tune_usb45467.conf is present in \etc\asterisk Keith DobbinsSr. IT Systems EngineerManaged File Transfer/Mainframe Networks3402 Linden Street Parkersburg, WV 26104-1608 Amateur Radio Call Sign: N8KLD On Tuesday, December 26, 2017, 11:40:18 AM EST, Steve Zingman <szingman@msgstor.com> wrote: Which channel driver are you using? Anything in the log? 73, Steve N4IRS On 12/26/2017 11:30 AM, Keith Dobbins wrote: I had my node working under ACID till a hard drive decided to crash on me. I did the re-install with the 32 bit DIAL install. Everything about the node appears to function properly but from asterisk to my URI I get ZERO audio in or out. It's the only audio adapter, and the URIDIAG with the loopback plug tests fine. It will activate the TX and I get the blinking green led but no audio in or out. Is there somewhere I can look to troubleshoot this issue? The motherboard is an older atom 330 board. Should I fall back to the older ACID install for this node which had worked. Thanks for any guidance that you can provide. Keith Dobbins N8KLD _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
participants (2)
-
Keith Dobbins -
Steve Zingman