- Allstar-Digital - lists.keekles.org

DMRGateway
by Robert Newberry 28 Nov '16

28 Nov '16

I have been playing around with the DV3000 and I noticed something interesting in regards to the "runaway delay" users that are rapid fire picket fencing seem to be the causing the problem. I was even able to see/hear the problem happen. I have 3 users on my repeater network. one of them was having a problem with the voter, another always has a extremely poor picket fence signal, and the last is on a VOX circuit who drops and picks up PTT a lot. The last two weeks two of the three people fixed their problems and had solid signals allowing for trouble free DMR <-> Allstar QSO for atleast a half hour. The third person who is perpetual weak showed up and instantly the dv3000 started building a delay. I did some targeted controlled testing and introduced what I'd call rapid key/unkey and I could make the delay start to a point where it appeared I somehow over loaded the DV3000 to start it dropping out. I then re ran the test with solid analog signals for 40 minutes and the gateway ran perfectly. I also am using on dv3000 between two repeaters and using the bridge to route the talkgroup for allstar audio to two repeaters which causes slow slurred audio on one repeater. I'm still trying to figure out how to stop this. The problem goes away when I remove the bridge rules to send the Allstar talkgroup to my other repeater. N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812, 42086, 42658, 42657 www.radioguysrepeaternetwork.com

2 2

Allstar <> dstar bridging PiDV
by Ken Boyle 04 Oct '16

04 Oct '16

5 12

Communications.support Forum
by Steve Zingman 03 Oct '16

03 Oct '16

If anyone has access to download files from the communications.support website, I need some help. Please contact me off list. For anyone that is not aware of the forum, I suggest you look into it. LOTS of good information available. 73, Steve N4IRS -- "Just say no to world domination"

2 1

Re: [Allstar Digital] Allstar-Digital Digest, Vol 12, Issue 6
by Tom 24 Sep '16

24 Sep '16

OK Jake. -----Original Message----- From: Allstar-Digital [mailto:allstar-digital-bounces@lists.keekles.org] On Behalf Of allstar-digital-request(a)lists.keekles.org Sent: Thursday, September 22, 2016 11:00 AM To: allstar-digital(a)lists.keekles.org Subject: Allstar-Digital Digest, Vol 12, Issue 6 Send Allstar-Digital mailing list submissions to allstar-digital(a)lists.keekles.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.keekles.org/cgi-bin/mailman/listinfo/allstar-digital or, via email, send a message with subject or body 'help' to allstar-digital-request(a)lists.keekles.org You can reach the person managing the list at allstar-digital-owner(a)lists.keekles.org When replying, please edit your Subject line so it is more specific than "Re: Contents of Allstar-Digital digest..."

1 0

Re: [Allstar Digital] Allstar-Digital Digest, Vol 12, Issue 5
by Chris HIll/K7AZ 21 Sep '16

21 Sep '16

Just curious if there are any plans, kits or plug and play setups available to allow for DMR to / from AllStar connections? Thank you, Chris K7AZ Lompoc CA Sent from my dumb-smart DROID...

3 2

ASL 2100 DMR
by David Shaw 21 Sep '16

21 Sep '16

Hello, Is ASL2100 linked to DMR 3167? -- 5.56X45= Thanks, David

3 2

Dial and DMRlink
by David Shaw 14 Sep '16

14 Sep '16

Is DMRlink going to be added to Dial as a default package? -- 5.56X45= Thanks, David

3 2

dmrgateway and dv3000 problem
by Robert Newberry 09 Sep '16

09 Sep '16

I am just posting a request for anyone's observations/help on dmrgatewway and the DV3000. I am having two issues, one of them I have been told is a known bug, the second appears to be something I am doing wrong. I may post over on the K0USYlink group to maybe catch people I'm missing. I will briefly explain my setup. Two XPR8400 repeaters. Site one has repeater and DMRlink along with DV3000 all co-located on the same LAN. Second site(repeater) peers to a master setup in DMRlink at site one. Both of these sites fucntion as they should using DMR. Problem is the "remote" site can communicate ASL<->DMR just fine. The site with all of my co-located equipment can only communicate ASL->DMR. DMR->ASL the audio on the analog side is slow and slurred. I posted hopefully all of the files you should need to view. https://drive.google.com/open?id=0B0dGQewXg1uxbFVLS0RSTWJ0QmM You do not need an account to look at them. I am hoping there are other people doing the same or similar thing and we can get together and compare notes. I am doing my best to post config files and trying to share what I am doing so other people can share their experiences too to help the community. -- N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812, 42086, 42658, 42657 www.radioguysrepeaternetwork.com

2 1

ambe_audio slurred
by Robert Newberry 03 Sep '16

03 Sep '16

I'm hoping someone can help. I've worked thru my issues adding a second repeater to my network here. The last issue I still can not resolve. On one of my repeaters in my network from DMR->ASL the audio is slurred and slow to analog users. On this same repeater ASL->DMR sounds fine. My second repeater works fine in both directions. I'm hoping there is someone here who is using a similar setup as me that might be willing to compare configurations with me. I've went back and forth thru the configurations trying to change things with out any success. Thank you. N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812, 42086, 42658, 42657 www.radioguysrepeaternetwork.com

3 3

Interconnecting BrandMeister and DMRlink and (HBlink)
by Steve Zingman 29 Aug '16

29 Aug '16

Since the application this list is built to support, I'm cross posting a message from Cort, N0MJS posted to the Yahoo K0USY Group linking software. If you are using DMRlink to run a DMR <---> ASL Gateway or if you are using DMRlink to provide the ability to connect to multiple networks with finite control of the TG / TS routing, Please post the attribution on your web site. Without DMRlink creating the DMR to ASL gateway would have been a LOT more work. As DMRlink and HBlink merge, we will have enhanced connectivity. If BrandMeister ever decides to support DMRlink trunking, so much the better. here's hoping. Cort's post below. Several people have contacted me recently about using DMRlink to connect to BrandMeister and about our “network". Thinking about the questions they’ve been asking, it seemed like a list post is in order. DMRlink’s bridge.py application uses a modified version of IPSC for trunking multiple simultaneous calls on the same timeslot between instances of bridge.py. If you’re running more than one bridge.py, you can stream many, many calls at the same time between them. BrandMeister does not implement this protocol. If you’re interconnecting with BrandMeister, you must NOT specify the IPSC is “TRUNK”, and you can only send one call per timeslot at a time. Also, it’s come up again about joining our “network”. K0USY group has not, is not, and will not build a “network”. We make tools. It’s unfortunate that there are NO OTHER groups in amateur DMR that can see the distinction between “network” and “networking software”. We’re writing software, and giving it away, and impose no rules on how you use it except that attribution must be given. Which is the last thing to touch on. The ONLY price you pay to use DMRlink or HBlink is to provide attribution as we’ve requested in the realm files in the repositories. The number of people who contact this list or one of the developers directly who use our tools is substantial, but when I do a Google search, I see almost nothing. If you’re using DMRlink, HBlink, or know someone who is, you are required to make public attribution – such as listing it as we’ve requested on your Web sties, etc. for your groups, clubs, networks, etc. This is not a joke. If I don’t start seeing proper attribution out there, we’ll be moving DMRlink and HBlink to non-public repositories and not release future developments publicly. -- Cort Buffington H: +1-785-813-1501 M: +1-785-865-7206 -- "Just say no to world domination"

4 4