Hi Guys I have tried loading ASL_1.01-20180228-armhf-nanopi image onto a NanoPi Seems to load fine I run the updates etc then the Menu all seems OK but AllStar does not seem to run ? return email: <mailto:bob@Fot.com.au> bob@Fot.com.au NODE=47324 REGPASS=47324:xxxxx@register.allstarlink.org ; This must be changed to your node number, password Call sign: VK6Z Interface type: SimpleUSB/usb_47324 ; SimpleUSB Echolink Callsign: INVALID Echolink node: 000000 ASL node used: Ping test to 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_seq=1 ttl=117 time=60.5 ms 64 bytes from 8.8.8.8: icmp_seq=2 ttl=117 time=60.1 ms 64 bytes from 8.8.8.8: icmp_seq=3 ttl=117 time=59.8 ms 64 bytes from 8.8.8.8: icmp_seq=4 ttl=117 time=60.1 ms --- 8.8.8.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3004ms rtt min/avg/max/mdev = 59.856/60.180/60.579/0.357 ms Ping test to register.allstarlink.org PING register.allstarlink.org (67.215.233.178) 56(84) bytes of data. 64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=1 ttl=50 time=209 ms 64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=2 ttl=50 time=208 ms 64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=3 ttl=50 time=208 ms 64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=4 ttl=50 time=287 ms --- register.allstarlink.org ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3004ms rtt min/avg/max/mdev = 208.420/228.404/287.132/33.912 ms Ouput of ifconfig eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.168.55 netmask 255.255.255.0 broadcast 192.168.168.255 inet6 fe80::6888:f0ff:fe2f:e5b prefixlen 64 scopeid 0x20<link> ether 6a:88:f0:2f:0e:5b txqueuelen 1000 (Ethernet) RX packets 2688 bytes 223583 (218.3 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 1227 bytes 325560 (317.9 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 33 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 32 bytes 2608 (2.5 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 32 bytes 2608 (2.5 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 Output of lsmod grep dahdi IAX2 registry Unable to connect to remote asterisk (does /var/run/asterisk.ctl exist?) Asterisk version: Unable to connect to remote asterisk (does /var/run/asterisk.ctl exist?) Current date and time: 2018-07-23.11:36 updatenodelist service running? root 657 0.0 0.4 4428 2392 ? Ss 11:14 0:00 /bin/bash /usr/local/bin/rc.updatenodelist & root 1637 0.0 0.1 3764 548 pts/0 S+ 11:40 0:00 grep updatenodelist /tmp/rpt_extnodes-temp file -rw-r--r-- 1 root root 0 Jul 23 11:15 /tmp/rpt_extnodes-temp /var/lib/asterisk/rpt_extnodes file -rwx------ 1 root root 141311 Jul 23 11:09 /var/lib/asterisk/rpt_extnodes ####### Begin warnings from messages file ####### Begin warnings from messages.1 file journalctl –xe Using username "repeater". repeater@repeater's password: _ _ ____ _ _ _ | \ | | __ _ _ __ ___ | _ \(_) | \ | | ___ ___ | \| |/ _` | '_ \ / _ \| |_) | | | \| |/ _ \/ _ \ | |\ | (_| | | | | (_) | __/| | | |\ | __/ (_) | |_| \_|\__,_|_| |_|\___/|_| |_| |_| \_|\___|\___/ Welcome to ARMBIAN 5.41 user-built Debian GNU/Linux 9 (stretch) 4.14.18-sunxi System load: 0.00 0.02 0.00 Up time: 9 min Local users: 2 Memory usage: 10 % of 493MB IP: 192.168.168.54 CPU temp: 29°C Usage of /: 10% of 15G Last login: Mon Jul 23 10:04:18 2018 from 192.168.168.26 repeater@repeater:~$ repeater@repeater:~$ sudo -s [sudo] password for repeater: root@repeater:/home/repeater# journalctl -xe -- The start-up result is done. Jul 23 10:05:21 repeater systemd[1]: dev-dahdi-pseudo.device: Job dev-dahdi-pseu Jul 23 10:05:21 repeater systemd[1]: Timed out waiting for device dev-dahdi-pseu -- Subject: Unit dev-dahdi-pseudo.device has failed -- Defined-By: systemd -- Support: <https://www.debian.org/support> https://www.debian.org/support -- -- Unit dev-dahdi-pseudo.device has failed. -- -- The result is timeout. Jul 23 10:05:21 repeater systemd[1]: Dependency failed for Asterisk PBX and tele -- Subject: Unit asterisk.service has failed -- Defined-By: systemd -- Support: <https://www.debian.org/support> https://www.debian.org/support -- -- Unit asterisk.service has failed. -- -- The result is dependency. Jul 23 10:05:21 repeater systemd[1]: asterisk.service: Job asterisk.service/star Jul 23 10:05:21 repeater systemd[1]: dev-dahdi-pseudo.device: Job dev-dahdi-pseu Jul 23 10:05:21 repeater sudo[1169]: pam_unix(sudo:session): session closed for Jul 23 10:06:23 repeater sudo[1370]: repeater : TTY=pts/2 ; PWD=/home/repeater ; Jul 23 10:06:23 repeater sudo[1370]: pam_unix(sudo:session): session opened for lines 1316-1338/1338 (END) Current default time zone: 'Australia/Perth' Local time is now: Mon Jul 23 09:35:43 AWST 2018. Universal Time is now: Mon Jul 23 01:35:43 UTC 2018. grep: /etc/systemd/network/eth0.network: No such file or directory /usr/local/sbin/net-setup: line 171: [: missing `]' mv: cannot stat '/tmp/extensions.conf.tmp': No such file or directory mv: cannot stat '/tmp/echolink.conf.tmp': No such file or directory mv: cannot stat '/tmp/iax.conf.tmp': No such file or directory mv: cannot stat '/tmp/modules.conf.tmp': No such file or directory mv: cannot stat '/tmp/rpt.conf.tmp': No such file or directory mv: cannot stat '/tmp/savenode.conf.tmp': No such file or directory mv: cannot stat '/tmp/manager.conf.tmp': No such file or directory mv: cannot stat '/tmp/usbradio.conf.tmp': No such file or directory mv: cannot stat '/tmp/simpleusb.conf.tmp': No such file or directory mv: cannot stat '/tmp/voter.conf.tmp': No such file or directory Using username "repeater". repeater@repeater's password: Anyone got any ideas ?? 73 VK6ZGN Bob <mailto:Bob@Fot.com.au> Bob@Fot.com.au Western Australia Mob. <tel:61%C2%A0%20%280%29%20418%20902%20194> 61 (0) 418 902 194 The contents of this e-mail (including any attachments) may be confidential and privileged. Any unauthorised use of this document or it's contents is prohibited. If you have received this e-mail in error, please notify us immediately and erase this document E&OE
Bob, It looks like DKMS did not rebuild DAHDI properly. Please do as root: dpkg-reconfigure asl-dahdi-linux-dkms reboot Should now be fixed. Check DAHDI is running by: lsmod | grep dahdi 73, Steve N4IRS On 07/25/2018 04:38 AM, Bob Good wrote:
Hi Guys
I have tried loading ASL_1.01-20180228-armhf-nanopi image onto a NanoPi
Seems to load fine I run the updates etc then the Menu all seems OK but AllStar does not seem to run ?
return email: bob@Fot.com.au <mailto:bob@Fot.com.au>
NODE=47324
REGPASS=47324:xxxxx@register.allstarlink.org ; This must be changed to your node number, password
Call sign: VK6Z
Interface type: SimpleUSB/usb_47324 ; SimpleUSB
Echolink Callsign: INVALID
Echolink node: 000000 ASL node used:
Ping test to 8.8.8.8
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_seq=1 ttl=117 time=60.5 ms
64 bytes from 8.8.8.8: icmp_seq=2 ttl=117 time=60.1 ms
64 bytes from 8.8.8.8: icmp_seq=3 ttl=117 time=59.8 ms
64 bytes from 8.8.8.8: icmp_seq=4 ttl=117 time=60.1 ms
--- 8.8.8.8 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3004ms
rtt min/avg/max/mdev = 59.856/60.180/60.579/0.357 ms
Ping test to register.allstarlink.org
PING register.allstarlink.org (67.215.233.178) 56(84) bytes of data.
64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=1 ttl=50 time=209 ms
64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=2 ttl=50 time=208 ms
64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=3 ttl=50 time=208 ms
64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=4 ttl=50 time=287 ms
--- register.allstarlink.org ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3004ms
rtt min/avg/max/mdev = 208.420/228.404/287.132/33.912 ms
Ouput of ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.168.55 netmask 255.255.255.0 broadcast 192.168.168.255
inet6 fe80::6888:f0ff:fe2f:e5b prefixlen 64 scopeid 0x20<link>
ether 6a:88:f0:2f:0e:5b txqueuelen 1000 (Ethernet)
RX packets 2688 bytes 223583 (218.3 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1227 bytes 325560 (317.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 33
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 32 bytes 2608 (2.5 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 32 bytes 2608 (2.5 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Output of lsmod grep dahdi
IAX2 registry
Unable to connect to remote asterisk (does /var/run/asterisk.ctl exist?)
Asterisk version:
Unable to connect to remote asterisk (does /var/run/asterisk.ctl exist?)
Current date and time: 2018-07-23.11:36
updatenodelist service running?
root 657 0.0 0.4 4428 2392 ? Ss 11:14 0:00 /bin/bash /usr/local/bin/rc.updatenodelist &
root 1637 0.0 0.1 3764 548 pts/0 S+ 11:40 0:00 grep updatenodelist
/tmp/rpt_extnodes-temp file
-rw-r--r-- 1 root root 0 Jul 23 11:15 /tmp/rpt_extnodes-temp
/var/lib/asterisk/rpt_extnodes file
-rwx------ 1 root root 141311 Jul 23 11:09 /var/lib/asterisk/rpt_extnodes
####### Begin warnings from messages file
####### Begin warnings from messages.1 file
journalctl –xe
Using username "repeater".
repeater@repeater's password:
_ _ ____ _ _ _
| \ | | __ _ _ __ ___ | _ \(_) | \ | | ___ ___
| \| |/ _` | '_ \ / _ \| |_) | | | \| |/ _ \/ _ \
| |\ | (_| | | | | (_) | __/| | | |\ | __/ (_) |
|_| \_|\__,_|_| |_|\___/|_| |_| |_| \_|\___|\___/
Welcome to ARMBIAN 5.41 user-built Debian GNU/Linux 9 (stretch) 4.14.18-sunxi
System load: 0.00 0.02 0.00 Up time: 9 min Local users: 2
Memory usage: 10 % of 493MB IP: 192.168.168.54
CPU temp: 29°C
Usage of /: 10% of 15G
Last login: Mon Jul 23 10:04:18 2018 from 192.168.168.26
repeater@repeater:~$
repeater@repeater:~$ sudo -s
[sudo] password for repeater:
root@repeater:/home/repeater# journalctl -xe
-- The start-up result is done.
Jul 23 10:05:21 repeater systemd[1]: dev-dahdi-pseudo.device: Job dev-dahdi-pseu
Jul 23 10:05:21 repeater systemd[1]: Timed out waiting for device dev-dahdi-pseu
-- Subject: Unit dev-dahdi-pseudo.device has failed
-- Defined-By: systemd
-- Support: https://www.debian.org/support
--
-- Unit dev-dahdi-pseudo.device has failed.
--
-- The result is timeout.
Jul 23 10:05:21 repeater systemd[1]: Dependency failed for Asterisk PBX and tele
-- Subject: Unit asterisk.service has failed
-- Defined-By: systemd
-- Support: https://www.debian.org/support
--
-- Unit asterisk.service has failed.
--
-- The result is dependency.
Jul 23 10:05:21 repeater systemd[1]: asterisk.service: Job asterisk.service/star
Jul 23 10:05:21 repeater systemd[1]: dev-dahdi-pseudo.device: Job dev-dahdi-pseu
Jul 23 10:05:21 repeater sudo[1169]: pam_unix(sudo:session): session closed for
Jul 23 10:06:23 repeater sudo[1370]: repeater : TTY=pts/2 ; PWD=/home/repeater ;
Jul 23 10:06:23 repeater sudo[1370]: pam_unix(sudo:session): session opened for
lines 1316-1338/1338 (END)
Current default time zone: 'Australia/Perth'
Local time is now: Mon Jul 23 09:35:43 AWST 2018.
Universal Time is now: Mon Jul 23 01:35:43 UTC 2018.
grep: /etc/systemd/network/eth0.network: No such file or directory
/usr/local/sbin/net-setup: line 171: [: missing `]'
mv: cannot stat '/tmp/extensions.conf.tmp': No such file or directory
mv: cannot stat '/tmp/echolink.conf.tmp': No such file or directory
mv: cannot stat '/tmp/iax.conf.tmp': No such file or directory
mv: cannot stat '/tmp/modules.conf.tmp': No such file or directory
mv: cannot stat '/tmp/rpt.conf.tmp': No such file or directory
mv: cannot stat '/tmp/savenode.conf.tmp': No such file or directory
mv: cannot stat '/tmp/manager.conf.tmp': No such file or directory
mv: cannot stat '/tmp/usbradio.conf.tmp': No such file or directory
mv: cannot stat '/tmp/simpleusb.conf.tmp': No such file or directory
mv: cannot stat '/tmp/voter.conf.tmp': No such file or directory
Using username "repeater".
repeater@repeater's password:
Anyone got any ideas ??
73
VK6ZGN */Bob/***Bob@Fot.com.au <mailto:Bob@Fot.com.au> Western Australia Mob. 61 (0) 418 902 194 <tel:61%C2%A0%20%280%29%20418%20902%20194>
The contents of this e-mail (including any attachments) may be confidential and privileged. Any unauthorised use of this document or it's contents is prohibited. If you have received this e-mail in error, please notify us immediately and erase this document E&OE
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Hi Steve Thanks that worked.. However now all seems to load and registers OK but SimpleUSB wont loa/run ? return email: Bob@Fot.com.au NODE=47324 REGPASS=47324:xxxxxx@register.allstarlink.org ; This must be changed to your node number, password Call sign: VK6ZGN Interface type: SimpleUSB/usb_47324 ; SimpleUSB Echolink Callsign: INVALID Echolink node: 000000 ASL node used: Ping test to 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_seq=1 ttl=117 time=77.5 ms 64 bytes from 8.8.8.8: icmp_seq=2 ttl=117 time=70.6 ms 64 bytes from 8.8.8.8: icmp_seq=3 ttl=117 time=84.1 ms 64 bytes from 8.8.8.8: icmp_seq=4 ttl=117 time=84.4 ms --- 8.8.8.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3004ms rtt min/avg/max/mdev = 70.664/79.212/84.453/5.656 ms Ping test to register.allstarlink.org PING register.allstarlink.org (67.215.233.178) 56(84) bytes of data. 64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=1 ttl=50 time=209 ms 64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=2 ttl=50 time=208 ms 64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=3 ttl=50 time=208 ms 64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=4 ttl=50 time=208 ms --- register.allstarlink.org ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3004ms rtt min/avg/max/mdev = 208.471/208.709/209.006/0.220 ms Ouput of ifconfig eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.168.39 netmask 255.255.255.0 broadcast 192.168.168.255 inet6 fe80::4f:49ff:fe38:5803 prefixlen 64 scopeid 0x20<link> ether 02:4f:49:38:58:03 txqueuelen 1000 (Ethernet) RX packets 1641 bytes 149786 (146.2 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 1781 bytes 554581 (541.5 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 33 lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 16 bytes 1312 (1.2 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 16 bytes 1312 (1.2 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 Output of lsmod grep dahdi dahdi 200704 28 IAX2 registry Host dnsmgr Username Perceived Refresh State 67.215.233.178:4569 Y 47324 58.178.114.94:64301 60 Registered Asterisk version: Asterisk GIT Version adaec47 built by root @ odroidxu4 on a armv7l running Linux on 2018-03-07 14:53:41 UTC Current date and time: 2018-07-26.04:32 updatenodelist service running? root 682 0.0 0.4 4428 2384 ? Ss 04:29 0:00 /bin/bash /usr/local/bin/rc.updatenodelist & root 1650 0.0 0.1 3764 560 pts/2 S+ 04:35 0:00 grep updatenodelist /tmp/rpt_extnodes-temp file -rw-r--r-- 1 root root 0 Jul 26 04:30 /tmp/rpt_extnodes-temp /var/lib/asterisk/rpt_extnodes file -rwx------ 1 root root 140551 Jul 26 04:26 /var/lib/asterisk/rpt_extnodes ####### Begin warnings from messages file [Jul 26 04:26:42] WARNING[987] chan_simpleusb.c: Loaded parameters from simpleusb_tune_usb_47324.conf for device usb_47324 . [Jul 26 04:26:42] WARNING[987] chan_simpleusb.c: Unable to re-open DSP device 1 (usb_47324): No such file or directory [Jul 26 04:26:42] WARNING[986] chan_simpleusb.c: Unable to re-open DSP device 1 (usb_47324): No such file or directory And so on forever !! ####### Begin warnings from messages.1 file 73 Bob VK6ZGN From: App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] On Behalf Of Steve Zingman Sent: Wednesday, 25 July 2018 17:58 To: Users of Asterisk app_rpt Subject: Re: [App_rpt-users] NanoPi Bob, It looks like DKMS did not rebuild DAHDI properly. Please do as root: dpkg-reconfigure asl-dahdi-linux-dkms reboot Should now be fixed. Check DAHDI is running by: lsmod | grep dahdi 73, Steve N4IRS On 07/25/2018 04:38 AM, Bob Good wrote: Hi Guys I have tried loading ASL_1.01-20180228-armhf-nanopi image onto a NanoPi Seems to load fine I run the updates etc then the Menu all seems OK but AllStar does not seem to run ? return email: bob@Fot.com.au NODE=47324 REGPASS=47324:xxxxx@register.allstarlink.org ; This must be changed to your node number, password Anyone got any ideas ?? 73 VK6ZGN Bob <mailto:Bob@Fot.com.au> Bob@Fot.com.au Western Australia Mob. <tel:61%C2%A0%20%280%29%20418%20902%20194> 61 (0) 418 902 194 The contents of this e-mail (including any attachments) may be confidential and privileged. Any unauthorised use of this document or it's contents is prohibited. If you have received this e-mail in error, please notify us immediately and erase this document E&OE _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
This is because OSS is not supported and marked as broken in current Linux distributions. You can either use a kernel that has it compiled in or you can do what I did and use: ALSA PulseAudio osspd (emulates oss through pulse) I’ll write up some basic instructions for how mine is working... but the net of it it is that without /dev/dsp1 your asl can’t send or receive audio via your sound card (URI) Maybe I’m talking out of turn, I did not read the entire thread back. Sent from the iRoad
On Jul 26, 2018, at 07:52, Bob Good <Bob@Fot.com.au> wrote:
Hi Steve
Thanks that worked…… However now all seems to load and registers OK but SimpleUSB wont loa/run ?
return email: Bob@Fot.com.au
NODE=47324 REGPASS=47324:xxxxxx@register.allstarlink.org ; This must be changed to your node number, password
Call sign: VK6ZGN Interface type: SimpleUSB/usb_47324 ; SimpleUSB Echolink Callsign: INVALID Echolink node: 000000 ASL node used:
Ping test to 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. 64 bytes from 8.8.8.8: icmp_seq=1 ttl=117 time=77.5 ms 64 bytes from 8.8.8.8: icmp_seq=2 ttl=117 time=70.6 ms 64 bytes from 8.8.8.8: icmp_seq=3 ttl=117 time=84.1 ms 64 bytes from 8.8.8.8: icmp_seq=4 ttl=117 time=84.4 ms
--- 8.8.8.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3004ms rtt min/avg/max/mdev = 70.664/79.212/84.453/5.656 ms
Ping test to register.allstarlink.org PING register.allstarlink.org (67.215.233.178) 56(84) bytes of data. 64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=1 ttl=50 time=209 ms 64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=2 ttl=50 time=208 ms 64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=3 ttl=50 time=208 ms 64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=4 ttl=50 time=208 ms
--- register.allstarlink.org ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3004ms rtt min/avg/max/mdev = 208.471/208.709/209.006/0.220 ms
Ouput of ifconfig eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.168.39 netmask 255.255.255.0 broadcast 192.168.168.255 inet6 fe80::4f:49ff:fe38:5803 prefixlen 64 scopeid 0x20<link> ether 02:4f:49:38:58:03 txqueuelen 1000 (Ethernet) RX packets 1641 bytes 149786 (146.2 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 1781 bytes 554581 (541.5 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 33
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 1000 (Local Loopback) RX packets 16 bytes 1312 (1.2 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 16 bytes 1312 (1.2 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Output of lsmod grep dahdi dahdi 200704 28
IAX2 registry Host dnsmgr Username Perceived Refresh State 67.215.233.178:4569 Y 47324 58.178.114.94:64301 60 Registered
Asterisk version: Asterisk GIT Version adaec47 built by root @ odroidxu4 on a armv7l running Linux on 2018-03-07 14:53:41 UTC
Current date and time: 2018-07-26.04:32
updatenodelist service running? root 682 0.0 0.4 4428 2384 ? Ss 04:29 0:00 /bin/bash /usr/local/bin/rc.updatenodelist & root 1650 0.0 0.1 3764 560 pts/2 S+ 04:35 0:00 grep updatenodelist
/tmp/rpt_extnodes-temp file -rw-r--r-- 1 root root 0 Jul 26 04:30 /tmp/rpt_extnodes-temp
/var/lib/asterisk/rpt_extnodes file -rwx------ 1 root root 140551 Jul 26 04:26 /var/lib/asterisk/rpt_extnodes
####### Begin warnings from messages file [Jul 26 04:26:42] WARNING[987] chan_simpleusb.c: Loaded parameters from simpleusb_tune_usb_47324.conf for device usb_47324 . [Jul 26 04:26:42] WARNING[987] chan_simpleusb.c: Unable to re-open DSP device 1 (usb_47324): No such file or directory [Jul 26 04:26:42] WARNING[986] chan_simpleusb.c: Unable to re-open DSP device 1 (usb_47324): No such file or directory And so on forever !!
####### Begin warnings from messages.1 file
73 Bob VK6ZGN
From: App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] On Behalf Of Steve Zingman Sent: Wednesday, 25 July 2018 17:58 To: Users of Asterisk app_rpt Subject: Re: [App_rpt-users] NanoPi
Bob, It looks like DKMS did not rebuild DAHDI properly.
Please do as root: dpkg-reconfigure asl-dahdi-linux-dkms reboot
Should now be fixed. Check DAHDI is running by: lsmod | grep dahdi
73, Steve N4IRS
On 07/25/2018 04:38 AM, Bob Good wrote:
Hi Guys
I have tried loading ASL_1.01-20180228-armhf-nanopi image onto a NanoPi
Seems to load fine I run the updates etc then the Menu all seems OK but AllStar does not seem to run ?
return email: bob@Fot.com.au
NODE=47324 REGPASS=47324:xxxxx@register.allstarlink.org ; This must be changed to your node number, password
Anyone got any ideas ??
73 VK6ZGN Bob Bob@Fot.com.au Western Australia Mob. 61 (0) 418 902 194
The contents of this e-mail (including any attachments) may be confidential and privileged. Any unauthorised use of this document or it's contents is prohibited. If you have received this e-mail in error, please notify us immediately and erase this document E&OE
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
JJ is correct. When the kernel was updated the new kernel no longer supports OSS. While waiting for JJ to publish his work around or for the dev team to produce a nono OSS channel driver, I'll post the info to put the kernel and headers on hold to keep OSS support. I'll have the info up by tomorrow morning. Steve N4IRS On 7/26/2018 9:08 AM, JJC wrote:
This is because OSS is not supported and marked as broken in current Linux distributions. You can either use a kernel that has it compiled in or you can do what I did and use:
ALSA PulseAudio osspd (emulates oss through pulse)
I’ll write up some basic instructions for how mine is working... but the net of it it is that without /dev/dsp1 your asl can’t send or receive audio via your sound card (URI)
Maybe I’m talking out of turn, I did not read the entire thread back.
Sent from the iRoad
On Jul 26, 2018, at 07:52, Bob Good <Bob@Fot.com.au <mailto:Bob@Fot.com.au>> wrote:
Hi Steve
Thanks that worked…… However now all seems to load and registers OK but SimpleUSB wont loa/run ?
return email: Bob@Fot.com.au <mailto:Bob@Fot.com.au>
NODE=47324
REGPASS=47324:xxxxxx@register.allstarlink.org <mailto:xxxxxx@register.allstarlink.org> ; This must be changed to your node number, password
Call sign: VK6ZGN
Interface type: SimpleUSB/usb_47324 ; SimpleUSB
Echolink Callsign: INVALID
Echolink node: 000000 ASL node used:
Ping test to 8.8.8.8
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_seq=1 ttl=117 time=77.5 ms
64 bytes from 8.8.8.8: icmp_seq=2 ttl=117 time=70.6 ms
64 bytes from 8.8.8.8: icmp_seq=3 ttl=117 time=84.1 ms
64 bytes from 8.8.8.8: icmp_seq=4 ttl=117 time=84.4 ms
--- 8.8.8.8 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3004ms
rtt min/avg/max/mdev = 70.664/79.212/84.453/5.656 ms
Ping test to register.allstarlink.org <http://register.allstarlink.org>
PING register.allstarlink.org <http://register.allstarlink.org> (67.215.233.178) 56(84) bytes of data.
64 bytes from seal.lambdatel.com <http://seal.lambdatel.com> (67.215.233.178): icmp_seq=1 ttl=50 time=209 ms
64 bytes from seal.lambdatel.com <http://seal.lambdatel.com> (67.215.233.178): icmp_seq=2 ttl=50 time=208 ms
64 bytes from seal.lambdatel.com <http://seal.lambdatel.com> (67.215.233.178): icmp_seq=3 ttl=50 time=208 ms
64 bytes from seal.lambdatel.com <http://seal.lambdatel.com> (67.215.233.178): icmp_seq=4 ttl=50 time=208 ms
--- register.allstarlink.org <http://register.allstarlink.org> ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3004ms
rtt min/avg/max/mdev = 208.471/208.709/209.006/0.220 ms
Ouput of ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.168.39 netmask 255.255.255.0 broadcast 192.168.168.255
inet6 fe80::4f:49ff:fe38:5803 prefixlen 64 scopeid 0x20<link>
ether 02:4f:49:38:58:03 txqueuelen 1000 (Ethernet)
RX packets 1641 bytes 149786 (146.2 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1781 bytes 554581 (541.5 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 33
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 16 bytes 1312 (1.2 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 16 bytes 1312 (1.2 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Output of lsmod grep dahdi
dahdi 200704 28
IAX2 registry
Host dnsmgr Username Perceived Refresh State
67.215.233.178:4569 Y 47324 58.178.114.94:64301 60 Registered
Asterisk version:
Asterisk GIT Version adaec47 built by root @ odroidxu4 on a armv7l running Linux on 2018-03-07 14:53:41 UTC
Current date and time: 2018-07-26.04:32
updatenodelist service running?
root 682 0.0 0.4 4428 2384 ? Ss 04:29 0:00 /bin/bash /usr/local/bin/rc.updatenodelist &
root 1650 0.0 0.1 3764 560 pts/2 S+ 04:35 0:00 grep updatenodelist
/tmp/rpt_extnodes-temp file
-rw-r--r-- 1 root root 0 Jul 26 04:30 /tmp/rpt_extnodes-temp
/var/lib/asterisk/rpt_extnodes file
-rwx------ 1 root root 140551 Jul 26 04:26 /var/lib/asterisk/rpt_extnodes
####### Begin warnings from messages file
[Jul 26 04:26:42] WARNING[987] chan_simpleusb.c: Loaded parameters from simpleusb_tune_usb_47324.conf for device usb_47324 .
[Jul 26 04:26:42] WARNING[987] chan_simpleusb.c: Unable to re-open DSP device 1 (usb_47324): No such file or directory
[Jul 26 04:26:42] WARNING[986] chan_simpleusb.c: Unable to re-open DSP device 1 (usb_47324): No such file or directory
And so on forever !!
####### Begin warnings from messages.1 file
73
Bob
VK6ZGN
*From:*App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] *On Behalf Of *Steve Zingman *Sent:* Wednesday, 25 July 2018 17:58 *To:* Users of Asterisk app_rpt *Subject:* Re: [App_rpt-users] NanoPi
Bob, It looks like DKMS did not rebuild DAHDI properly.
Please do as root: dpkg-reconfigure asl-dahdi-linux-dkms reboot
Should now be fixed. Check DAHDI is running by: lsmod | grep dahdi
73, Steve N4IRS
On 07/25/2018 04:38 AM, Bob Good wrote:
Hi Guys
I have tried loading ASL_1.01-20180228-armhf-nanopi image onto a NanoPi
Seems to load fine I run the updates etc then the Menu all seems OK but AllStar does not seem to run ?
return email: bob@Fot.com.au <mailto:bob@Fot.com.au>
NODE=47324
REGPASS=47324:xxxxx@register.allstarlink.org <mailto:REGPASS=47324:xxxxx@register.allstarlink.org> ; This must be changed to your node number, password
Anyone got any ideas ??
73
VK6ZGN */Bob/ * Bob@Fot.com.au <mailto:Bob@Fot.com.au> Western Australia Mob. 61 (0) 418 902 194 <tel:61%C2%A0%20%280%29%20418%20902%20194>
The contents of this e-mail (including any attachments) may be confidential and privileged. Any unauthorised use of this document or it's contents is prohibited. If you have received this e-mail in error, please notify us immediately and erase this document E&OE
_______________________________________________
App_rpt-users mailing list
App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org>
http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visithttp://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org <mailto:App_rpt-users@lists.allstarlink.org> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Hi Steve Thks for the response ! Where can I download the solution ? Thks for all your work 73 Bob VK6ZGN On 26 July 2018 21:56:18 Steve Zingman <szingman@msgstor.com> wrote:
JJ is correct. When the kernel was updated the new kernel no longer supports OSS. While waiting for JJ to publish his work around or for the dev team to produce a nono OSS channel driver, I'll post the info to put the kernel and headers on hold to keep OSS support. I'll have the info up by tomorrow morning.
Steve N4IRS
On 7/26/2018 9:08 AM, JJC wrote:
This is because OSS is not supported and marked as broken in current Linux distributions. You can either use a kernel that has it compiled in or you can do what I did and use:
ALSA PulseAudio osspd (emulates oss through pulse)
I’ll write up some basic instructions for how mine is working... but the net of it it is that without /dev/dsp1 your asl can’t send or receive audio via your sound card (URI)
Maybe I’m talking out of turn, I did not read the entire thread back.
Sent from the iRoad
On Jul 26, 2018, at 07:52, Bob Good <Bob@Fot.com.au> wrote:
Hi Steve
Thanks that worked…… However now all seems to load and registers OK but SimpleUSB wont loa/run ?
return email: Bob@Fot.com.au
NODE=47324
REGPASS=47324:xxxxxx@register.allstarlink.org ; This must be changed to your node number, password
Call sign: VK6ZGN
Interface type: SimpleUSB/usb_47324 ; SimpleUSB
Echolink Callsign: INVALID
Echolink node: 000000 ASL node used:
Ping test to 8.8.8.8
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_seq=1 ttl=117 time=77.5 ms
64 bytes from 8.8.8.8: icmp_seq=2 ttl=117 time=70.6 ms
64 bytes from 8.8.8.8: icmp_seq=3 ttl=117 time=84.1 ms
64 bytes from 8.8.8.8: icmp_seq=4 ttl=117 time=84.4 ms
--- 8.8.8.8 ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3004ms
rtt min/avg/max/mdev = 70.664/79.212/84.453/5.656 ms
Ping test to register.allstarlink.org
PING register.allstarlink.org (67.215.233.178) 56(84) bytes of data.
64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=1 ttl=50 time=209 ms
64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=2 ttl=50 time=208 ms
64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=3 ttl=50 time=208 ms
64 bytes from seal.lambdatel.com (67.215.233.178): icmp_seq=4 ttl=50 time=208 ms
--- register.allstarlink.org ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3004ms
rtt min/avg/max/mdev = 208.471/208.709/209.006/0.220 ms
Ouput of ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.168.39 netmask 255.255.255.0 broadcast 192.168.168.255
inet6 fe80::4f:49ff:fe38:5803 prefixlen 64 scopeid 0x20<link>
ether 02:4f:49:38:58:03 txqueuelen 1000 (Ethernet)
RX packets 1641 bytes 149786 (146.2 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1781 bytes 554581 (541.5 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 33
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 16 bytes 1312 (1.2 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 16 bytes 1312 (1.2 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
Output of lsmod grep dahdi
dahdi 200704 28
IAX2 registry
Host dnsmgr Username Perceived Refresh State
67.215.233.178:4569 Y 47324 58.178.114.94:64301 60 Registered
Asterisk version:
Asterisk GIT Version adaec47 built by root @ odroidxu4 on a armv7l running Linux on 2018-03-07 14:53:41 UTC
Current date and time: 2018-07-26.04:32
updatenodelist service running?
root 682 0.0 0.4 4428 2384 ? Ss 04:29 0:00 /bin/bash /usr/local/bin/rc.updatenodelist &
root 1650 0.0 0.1 3764 560 pts/2 S+ 04:35 0:00 grep updatenodelist
/tmp/rpt_extnodes-temp file
-rw-r--r-- 1 root root 0 Jul 26 04:30 /tmp/rpt_extnodes-temp
/var/lib/asterisk/rpt_extnodes file
-rwx------ 1 root root 140551 Jul 26 04:26 /var/lib/asterisk/rpt_extnodes
####### Begin warnings from messages file
[Jul 26 04:26:42] WARNING[987] chan_simpleusb.c: Loaded parameters from simpleusb_tune_usb_47324.conf for device usb_47324 .
[Jul 26 04:26:42] WARNING[987] chan_simpleusb.c: Unable to re-open DSP device 1 (usb_47324): No such file or directory
[Jul 26 04:26:42] WARNING[986] chan_simpleusb.c: Unable to re-open DSP device 1 (usb_47324): No such file or directory
And so on forever !!
####### Begin warnings from messages.1 file
73
Bob
VK6ZGN
From: App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] On Behalf Of Steve Zingman Sent: Wednesday, 25 July 2018 17:58 To: Users of Asterisk app_rpt Subject: Re: [App_rpt-users] NanoPi
Bob, It looks like DKMS did not rebuild DAHDI properly.
Please do as root: dpkg-reconfigure asl-dahdi-linux-dkms reboot
Should now be fixed. Check DAHDI is running by: lsmod | grep dahdi
73, Steve N4IRS
On 07/25/2018 04:38 AM, Bob Good wrote:
Hi Guys
I have tried loading ASL_1.01-20180228-armhf-nanopi image onto a NanoPi
Seems to load fine I run the updates etc then the Menu all seems OK but AllStar does not seem to run ?
return email: bob@Fot.com.au
NODE=47324
REGPASS=47324:xxxxx@register.allstarlink.org ; This must be changed to your node number, password
Anyone got any ideas ??
73
VK6ZGN Bob Bob@Fot.com.au Western Australia Mob. 61 (0) 418 902 194
The contents of this e-mail (including any attachments) may be confidential and privileged. Any unauthorised use of this document or it's contents is prohibited. If you have received this e-mail in error, please notify us immediately and erase this document E&OE
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
participants (4)
-
Bob -
Bob Good
-
JJC -
Steve Zingman