Re: [App_rpt-users] Node Status not showing...
Yeah, I can wait and see what develops. It's not the end of the world; it's just getting the online status is better manners than subjecting everyone (who isn't on a repeater with unnecessary Alison jabbering turned off) having to hear 30 repeater connections listed over the air... Bob/KK6RQ On Sun, Jan 11, 2015 at 8:28 PM, <mike@midnighteng.com> wrote:
You could be having some problems with internet host (especially if it is comcast). Probably temporary, don't go changing your settings over it just yet. Give it a few days and reboots (computer and router) to see how it pans out.
...mike/kb8jnm
-------- Original Message -------- Subject: Re: [App_rpt-users] Node Status not showing... From: Jah Rastafari <nuhtrue@gmail.com> Date: Sun, January 11, 2015 9:20 pm To: mike@midnighteng.com, "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
I went back right after reading your reply (several hours after my original post) and it in fact came up the way it should. But then 5 minutes later it went back to saying I wasn't connected. I'm not sure what it means but I can say I've never seen it behave like this before.
On Sun, Jan 11, 2015 at 4:56 PM, <mike@midnighteng.com> wrote:
Not sure but....
I think you are only suffering from a delay of the update to the list.
Try waiting for a short while (up to 30min) and look again. Others have said it takes that long sometimes but I have only witnessed about 5-6min.
Guess it depends on how busy the server is.
...mike/kb8jnm
-------- Original Message -------- Subject: [App_rpt-users] Node Status not showing... From: Jah Rastafari <nuhtrue@gmail.com> Date: Sun, January 11, 2015 5:29 pm To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Forgive me if this has already been discussed and I missed it, but I
just
noticed recently that although I was connected to a number of other nodes/repeaters, the 'Node Status' selection on the Allstar site says I'm not connected to anything. My node(s) show up properly in the available node list and everything else is as it should be. The Web Transceiver works properly also and I haven't changed anything recently. Am I missing something?
Bob/ KK6RQ<hr>_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Not sure if your name is Jah, or Bob. But at any rate, I recently setup my first simplex allstar node and managed to hit the wrong command sequence and triggered a long train of announcements listing all the connected nodes. You mean to say that I'm not the only one who heard that? Most embarrassing. It eventually stopped abruptly and I did find myself disconnected. Hmm... On Sun Jan 11 2015 at 8:26:09 PM Jah Rastafari <nuhtrue@gmail.com> wrote:
Yeah, I can wait and see what develops. It's not the end of the world; it's just getting the online status is better manners than subjecting everyone (who isn't on a repeater with unnecessary Alison jabbering turned off) having to hear 30 repeater connections listed over the air...
Bob/KK6RQ
On Sun, Jan 11, 2015 at 8:28 PM, <mike@midnighteng.com> wrote:
You could be having some problems with internet host (especially if it is comcast). Probably temporary, don't go changing your settings over it just yet. Give it a few days and reboots (computer and router) to see how it pans out.
...mike/kb8jnm
-------- Original Message --------
Subject: Re: [App_rpt-users] Node Status not showing...
From: Jah Rastafari <nuhtrue@gmail.com>
Date: Sun, January 11, 2015 9:20 pm
To: mike@midnighteng.com, "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
I went back right after reading your reply (several hours after my original post) and it in fact came up the way it should. But then 5 minutes later it went back to saying I wasn't connected. I'm not sure what it means but I can say I've never seen it behave like this before.
On Sun, Jan 11, 2015 at 4:56 PM, <mike@midnighteng.com> wrote:
Not sure but....
I think you are only suffering from a delay of the update to the list.
Try waiting for a short while (up to 30min) and look again. Others have said it takes that long sometimes but I have only
witnessed
about 5-6min.
Guess it depends on how busy the server is.
...mike/kb8jnm
-------- Original Message -------- Subject: [App_rpt-users] Node Status not showing... From: Jah Rastafari <nuhtrue@gmail.com> Date: Sun, January 11, 2015 5:29 pm To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Forgive me if this has already been discussed and I missed it, but I just noticed recently that although I was connected to a number of other nodes/repeaters, the 'Node Status' selection on the Allstar site says I'm not connected to anything. My node(s) show up properly in the available node list and everything else is as it should be. The Web Transceiver works properly also and I haven't changed anything recently. Am I missing something?
Bob/ KK6RQ<hr>_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/ mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
Sort of; I'm referring to the malfunction of the online/visual alternative to querying which nodes one is connected to because the Alison verbal readout pisses a lot of people off if you're connected to more than a couple. Oh and btw the account was originally setup with the tongue-in-cheek name Jah Rastafari to order reggae records. I often forget it's even there. -Bob/KK6RQ On Mon, Jan 12, 2015 at 3:10 PM, Elden Fenison <w7ldn@w7ldn.com> wrote:
Not sure if your name is Jah, or Bob. But at any rate, I recently setup my first simplex allstar node and managed to hit the wrong command sequence and triggered a long train of announcements listing all the connected nodes. You mean to say that I'm not the only one who heard that? Most embarrassing. It eventually stopped abruptly and I did find myself disconnected. Hmm...
On Sun Jan 11 2015 at 8:26:09 PM Jah Rastafari <nuhtrue@gmail.com> wrote:
Yeah, I can wait and see what develops. It's not the end of the world; it's just getting the online status is better manners than subjecting everyone (who isn't on a repeater with unnecessary Alison jabbering turned off) having to hear 30 repeater connections listed over the air...
Bob/KK6RQ
On Sun, Jan 11, 2015 at 8:28 PM, <mike@midnighteng.com> wrote:
You could be having some problems with internet host (especially if it is comcast). Probably temporary, don't go changing your settings over it just yet. Give it a few days and reboots (computer and router) to see how it pans out.
...mike/kb8jnm
-------- Original Message --------
Subject: Re: [App_rpt-users] Node Status not showing...
From: Jah Rastafari <nuhtrue@gmail.com>
Date: Sun, January 11, 2015 9:20 pm
To: mike@midnighteng.com, "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
I went back right after reading your reply (several hours after my original post) and it in fact came up the way it should. But then 5 minutes later it went back to saying I wasn't connected. I'm not sure what it means but I can say I've never seen it behave like this before.
On Sun, Jan 11, 2015 at 4:56 PM, <mike@midnighteng.com> wrote:
Not sure but....
I think you are only suffering from a delay of the update to the
list.
Try waiting for a short while (up to 30min) and look again. Others have said it takes that long sometimes but I have only
witnessed
about 5-6min.
Guess it depends on how busy the server is.
...mike/kb8jnm
-------- Original Message -------- Subject: [App_rpt-users] Node Status not showing... From: Jah Rastafari <nuhtrue@gmail.com> Date: Sun, January 11, 2015 5:29 pm To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Forgive me if this has already been discussed and I missed it, but I just noticed recently that although I was connected to a number of other nodes/repeaters, the 'Node Status' selection on the Allstar site says I'm not connected to anything. My node(s) show up properly in the available node list and everything else is as it should be. The Web Transceiver works properly also and I haven't changed anything recently. Am I missing something?
Bob/ KK6RQ<hr>_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/ mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
There is a problem with the status server and I am sure the powers to be will look into it. Until then you can live without it. Also I have mentioned this before. If you don't want to hear constant connect/disconnect messages set the following two parameters in your node stanza in rpt.conf holdofftelem=1 telemdefault=2 This will announce connect/disconnect messages YOU make but them will mute others after about 30 seconds. This is a good compromise giving you feedback of what you do but not others. This is the default setting in the BBB code. 73 Doug WA3DSP http://www.crompton.com/hamradio Date: Mon, 12 Jan 2015 15:47:17 -0600 From: nuhtrue@gmail.com To: w7ldn@w7ldn.com; app_rpt-users@ohnosec.org Subject: Re: [App_rpt-users] Node Status not showing... Sort of; I'm referring to the malfunction of the online/visual alternative to querying which nodes one is connected to because the Alison verbal readout pisses a lot of people off if you're connected to more than a couple. Oh and btw the account was originally setup with the tongue-in-cheek name Jah Rastafari to order reggae records. I often forget it's even there. -Bob/KK6RQ On Mon, Jan 12, 2015 at 3:10 PM, Elden Fenison <w7ldn@w7ldn.com> wrote: Not sure if your name is Jah, or Bob. But at any rate, I recently setup my first simplex allstar node and managed to hit the wrong command sequence and triggered a long train of announcements listing all the connected nodes. You mean to say that I'm not the only one who heard that? Most embarrassing. It eventually stopped abruptly and I did find myself disconnected. Hmm... On Sun Jan 11 2015 at 8:26:09 PM Jah Rastafari <nuhtrue@gmail.com> wrote: Yeah, I can wait and see what develops. It's not the end of the world; it's just getting the online status is better manners than subjecting everyone (who isn't on a repeater with unnecessary Alison jabbering turned off) having to hear 30 repeater connections listed over the air... Bob/KK6RQ On Sun, Jan 11, 2015 at 8:28 PM, <mike@midnighteng.com> wrote: You could be having some problems with internet host (especially if it is comcast). Probably temporary, don't go changing your settings over it just yet. Give it a few days and reboots (computer and router) to see how it pans out. ...mike/kb8jnm
-------- Original Message --------
Subject: Re: [App_rpt-users] Node Status not showing...
From: Jah Rastafari <nuhtrue@gmail.com>
Date: Sun, January 11, 2015 9:20 pm
To: mike@midnighteng.com, "app_rpt-users@ohnosec.org"
<app_rpt-users@ohnosec.org>
I went back right after reading your reply (several hours after my original
post) and it in fact came up the way it should. But then 5 minutes
later it went back to saying I wasn't connected. I'm not sure what it means
but I can say I've never seen it behave like this before.
On Sun, Jan 11, 2015 at 4:56 PM, <mike@midnighteng.com> wrote:
Not sure but....
I think you are only suffering from a delay of the update to the list.
Try waiting for a short while (up to 30min) and look again.
Others have said it takes that long sometimes but I have only witnessed
about 5-6min.
Guess it depends on how busy the server is.
...mike/kb8jnm
-------- Original Message --------
Subject: [App_rpt-users] Node Status not showing...
From: Jah Rastafari <nuhtrue@gmail.com>
Date: Sun, January 11, 2015 5:29 pm
To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Forgive me if this has already been discussed and I missed it, but I just
noticed recently that although I was connected to a number of other
nodes/repeaters, the 'Node Status' selection on the Allstar site says I'm
not connected to anything. My node(s) show up properly in the available
node list and everything else is as it should be. The Web Transceiver
works
properly also and I haven't changed anything recently. Am I missing
something?
Bob/ KK6RQ<hr>_______________________________________________
App_rpt-users mailing list
App_rpt-users@ohnosec.org
To unsubscribe from this list please visit
http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down
to the bottom of the page. Enter your email address and press the
"Unsubscribe or edit options button"
You do not need a password to unsubscribe, you can do it via email
confirmation. If you have trouble unsubscribing, please send a message to
the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
There are two node list commands: ilink 5 is list of directly connected nodes only. ilink 15 is full list of all connected nodes no mater how many hops away (AKA Long Range Sensors) I recommend using ilink 5 in your functions and the AllStar web site for the bigger picture. Neither command will cause remotes nodes to dump telemetry unless they have telemdefault=1 or you’re unlucky enough to hit their telemdefault=2 timeout window. -- Tim :wq
On Jan 12, 2015, at 1:47 PM, Jah Rastafari <nuhtrue@gmail.com> wrote:
Sort of; I'm referring to the malfunction of the online/visual alternative to querying which nodes one is connected to because the Alison verbal readout pisses a lot of people off if you're connected to more than a couple.
Oh and btw the account was originally setup with the tongue-in-cheek name Jah Rastafari to order reggae records. I often forget it's even there.
-Bob/KK6RQ
On Mon, Jan 12, 2015 at 3:10 PM, Elden Fenison <w7ldn@w7ldn.com <mailto:w7ldn@w7ldn.com>> wrote: Not sure if your name is Jah, or Bob. But at any rate, I recently setup my first simplex allstar node and managed to hit the wrong command sequence and triggered a long train of announcements listing all the connected nodes. You mean to say that I'm not the only one who heard that? Most embarrassing. It eventually stopped abruptly and I did find myself disconnected. Hmm...
On Sun Jan 11 2015 at 8:26:09 PM Jah Rastafari <nuhtrue@gmail.com <mailto:nuhtrue@gmail.com>> wrote: Yeah, I can wait and see what develops. It's not the end of the world; it's just getting the online status is better manners than subjecting everyone (who isn't on a repeater with unnecessary Alison jabbering turned off) having to hear 30 repeater connections listed over the air...
Bob/KK6RQ
On Sun, Jan 11, 2015 at 8:28 PM, <mike@midnighteng.com <mailto:mike@midnighteng.com>> wrote:
You could be having some problems with internet host (especially if it is comcast). Probably temporary, don't go changing your settings over it just yet. Give it a few days and reboots (computer and router) to see how it pans out.
...mike/kb8jnm
-------- Original Message -------- Subject: Re: [App_rpt-users] Node Status not showing... From: Jah Rastafari <nuhtrue@gmail.com <mailto:nuhtrue@gmail.com>> Date: Sun, January 11, 2015 9:20 pm To: mike@midnighteng.com <mailto:mike@midnighteng.com>, "app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org>" <app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org>>
I went back right after reading your reply (several hours after my original post) and it in fact came up the way it should. But then 5 minutes later it went back to saying I wasn't connected. I'm not sure what it means but I can say I've never seen it behave like this before.
On Sun, Jan 11, 2015 at 4:56 PM, <mike@midnighteng.com <mailto:mike@midnighteng.com>> wrote:
Not sure but....
I think you are only suffering from a delay of the update to the list.
Try waiting for a short while (up to 30min) and look again. Others have said it takes that long sometimes but I have only witnessed about 5-6min.
Guess it depends on how busy the server is.
...mike/kb8jnm
-------- Original Message -------- Subject: [App_rpt-users] Node Status not showing... From: Jah Rastafari <nuhtrue@gmail.com <mailto:nuhtrue@gmail.com>> Date: Sun, January 11, 2015 5:29 pm To: "app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org>" <app_rpt-users@ohnosec.org <mailto:app_rpt-users@ohnosec.org>>
Forgive me if this has already been discussed and I missed it, but I just noticed recently that although I was connected to a number of other nodes/repeaters, the 'Node Status' selection on the Allstar site says I'm not connected to anything. My node(s) show up properly in the available node list and everything else is as it should be. The Web Transceiver works properly also and I haven't changed anything recently. Am I missing something?
Bob/ KK6RQ<hr>_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
App_rpt-users mailing list App_rpt-users@ohnosec.org <mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users>
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users <http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users> and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
When I have a minute to poke my head above water I'll get on the air and speak with you Tim and pummel you with questions so I don't butcher things. I basically understand it, I just want to be certain all my semicolons are where (and WHY) they're supposed to be. Bob/KK6RQ On Mon, Jan 12, 2015 at 4:26 PM, Tim Sawyer <tim.sawyer@mac.com> wrote:
There are two node list commands:
ilink 5 is list of directly connected nodes only. ilink 15 is full list of all connected nodes no mater how many hops away (AKA Long Range Sensors)
I recommend using ilink 5 in your functions and the AllStar web site for the bigger picture.
Neither command will cause remotes nodes to dump telemetry unless they have telemdefault=1 or you’re unlucky enough to hit their telemdefault=2 timeout window.
-- Tim :wq
On Jan 12, 2015, at 1:47 PM, Jah Rastafari <nuhtrue@gmail.com> wrote:
Sort of; I'm referring to the malfunction of the online/visual alternative to querying which nodes one is connected to because the Alison verbal readout pisses a lot of people off if you're connected to more than a couple.
Oh and btw the account was originally setup with the tongue-in-cheek name Jah Rastafari to order reggae records. I often forget it's even there.
-Bob/KK6RQ
On Mon, Jan 12, 2015 at 3:10 PM, Elden Fenison <w7ldn@w7ldn.com> wrote:
Not sure if your name is Jah, or Bob. But at any rate, I recently setup my first simplex allstar node and managed to hit the wrong command sequence and triggered a long train of announcements listing all the connected nodes. You mean to say that I'm not the only one who heard that? Most embarrassing. It eventually stopped abruptly and I did find myself disconnected. Hmm...
On Sun Jan 11 2015 at 8:26:09 PM Jah Rastafari <nuhtrue@gmail.com> wrote:
Yeah, I can wait and see what develops. It's not the end of the world; it's just getting the online status is better manners than subjecting everyone (who isn't on a repeater with unnecessary Alison jabbering turned off) having to hear 30 repeater connections listed over the air...
Bob/KK6RQ
On Sun, Jan 11, 2015 at 8:28 PM, <mike@midnighteng.com> wrote:
You could be having some problems with internet host (especially if it is comcast). Probably temporary, don't go changing your settings over it just yet. Give it a few days and reboots (computer and router) to see how it pans out.
...mike/kb8jnm
-------- Original Message --------
Subject: Re: [App_rpt-users] Node Status not showing...
From: Jah Rastafari <nuhtrue@gmail.com>
Date: Sun, January 11, 2015 9:20 pm
To: mike@midnighteng.com, "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
I went back right after reading your reply (several hours after my original post) and it in fact came up the way it should. But then 5 minutes later it went back to saying I wasn't connected. I'm not sure what it means but I can say I've never seen it behave like this before.
On Sun, Jan 11, 2015 at 4:56 PM, <mike@midnighteng.com> wrote:
Not sure but....
I think you are only suffering from a delay of the update to the
list.
Try waiting for a short while (up to 30min) and look again. Others have said it takes that long sometimes but I have only
witnessed
about 5-6min.
Guess it depends on how busy the server is.
...mike/kb8jnm
-------- Original Message -------- Subject: [App_rpt-users] Node Status not showing... From: Jah Rastafari <nuhtrue@gmail.com> Date: Sun, January 11, 2015 5:29 pm To: "app_rpt-users@ohnosec.org" <app_rpt-users@ohnosec.org>
Forgive me if this has already been discussed and I missed it, but I just noticed recently that although I was connected to a number of other nodes/repeaters, the 'Node Status' selection on the Allstar site says I'm not connected to anything. My node(s) show up properly in the available node list and everything else is as it should be. The Web Transceiver works properly also and I haven't changed anything recently. Am I missing something?
Bob/ KK6RQ<hr>_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/ mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
_______________________________________________ App_rpt-users mailing list App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.
participants (4)
-
Doug Crompton -
Elden Fenison -
Jah Rastafari -
Tim Sawyer