July 2013 - App_rpt-users - lists.keekles.org

Re: [App_rpt-users] App_rpt-users Digest, Vol 52, Issue 31
by Bill Hurlock 12 Jul '13

12 Jul '13

I had the same problem and the solution I used, because I use SIP, was to change the default SIP port to a non standard port which stopped all the bogus junk from happening. Bill Hurlock -----Original Message----- From: app_rpt-users-bounces(a)ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of app_rpt-users-request(a)ohnosec.org Sent: Sunday, June 23, 2013 6:43 PM To: app_rpt-users(a)ohnosec.org Subject: App_rpt-users Digest, Vol 52, Issue 31 Send App_rpt-users mailing list submissions to app_rpt-users(a)ohnosec.org To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request(a)ohnosec.org You can reach the person managing the list at app_rpt-users-owner(a)ohnosec.org When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..."

1 0

Re : Re: Computing Hardware....
by pete M 11 Jul '13

11 Jul '13

I second. I have use a thin client (hp) for a few moths with acid. I had to install a small 44 pin ide drive for rhe install bur all was well.. I would not have run 2 node on radio usb but one was perfect --- Message initial --- De : "Benjamin L. Naber" <Benjamin(a)kb9lfz.com> Envoyé : 9 juillet 2013 16:43 A : "James Hill" <jrh(a)g0fhm.co.uk> Cc: app_rpt-users(a)ohnosec.org Objet : Re: [App_rpt-users] Computing Hardware.... James, Might a recommend a thin client? They are very cheap, under $20 USD, sometimes including free shipping on eBay! I have zero idea what other folks have success with, but I'm using Limey Linux on a Neoware CA-22 that I bought a few years ago for about $40 USD. Very low power, in the order of 13W... Well, my ADD took over so I went to check. During boot, the thin client peaked at about 18.5W. When fully booted to prompt, meaning idle Node, power consumption was 13W. I am going to see if I can power the whole setup using a wheel chair battery and a 3A or 5A supply. I have my node radio at 5W. Because it sits idle most of the time, and current draw from the radio during TX is 2.4A, this will be fine, even when I'm connected to a another node and mostly listening. Think about it... ~Benjamin, KB9LFZ On Sun, 2013-07-07 at 13:57 +0100, James Hill wrote: > Guys, > > The old laptop that I use on my node is just about ready to roll over > and die (numerous SMART warnings, and it's getting extremely hot). > > I'm looking for new hardware options. > > Any suggestions? In an ideal world, I would like to use my Pi with > simpleusb (PL is handled by radio with hardware COR), but from reading > the archives, it's been said that it is likely to never happen. Has > anyone actually used a Pi & made it work? > > Or, what about a Thin Client? > > I haven't got that much money to splash on new stuff, and I need > something with a low (ish) power consumption. > > Any ideas would be appreciated! > > Cheers, > > James G0FHM > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

3 4

chan_usbradio.c error
by Michael Hebert 10 Jul '13

10 Jul '13

All, Every night at around 0108 in the morning my box has an error that reads "[Jul 6 01:08:18] ERROR[5730] chan_usbradio.c: HID process has died or something!!" After the error, the app_rpt.c reloads and i loose all the nodes that are connected to me or that i am connected to. Anyone have thoughts? Thanks, Mike - KD5DFB

2 2

Incoming Calls from SipGate
by torben＠klimt-online.com 10 Jul '13

10 Jul '13

Hi all, anybody here who can help me installing my sipgateaccount into the allstarlink box ? i would like to call the sipgate phone number to "connect" to the repeater. is there a possibility, that only "special" numbers cann call the sipgate telefon number ? i think i must do changes in sip.conf (for the sipgate registration) and extension.conf (for answer the call and connect to the repeater) greetings Torben Klimt Eicherstrasse 58 85123 Karlskron-Grillheim Telefon: 08453-34 45 040 Fax: 08453 - 4085296 Mobil: 0151-178 74499 torben(a)klimt-online.com<mailto:torben@klimt-online.com>

1 0

Computing Hardware....
by James Hill 09 Jul '13

09 Jul '13

Guys, The old laptop that I use on my node is just about ready to roll over and die (numerous SMART warnings, and it's getting extremely hot). I'm looking for new hardware options. Any suggestions? In an ideal world, I would like to use my Pi with simpleusb (PL is handled by radio with hardware COR), but from reading the archives, it's been said that it is likely to never happen. Has anyone actually used a Pi & made it work? Or, what about a Thin Client? I haven't got that much money to splash on new stuff, and I need something with a low (ish) power consumption. Any ideas would be appreciated! Cheers, James G0FHM

2 1

SIP/IAX access
by Mark Johnston 09 Jul '13

09 Jul '13

Does anyone know the correct configuration/what else I have to do to get SIP or IAX access working? I tried this A user stanza in sip.conf or iax.conf should look like this: [my-ip-phone] type=user context=radiocontrol auth=md5 secret=nunya ; Important! Change this!!! disallow=all allow=gsm allow=ulaw transfer=no The radiocontrol context in extensions.conf should look like this: [radio-control] ; Change all instances of 1234 to your node num. exten=1234,1,Answer exten=1234,n,Playback,rpt/node exten=1234,n,Playback,digits/1 exten=1234,n,Playback,digits/2 exten=1234,n,Playback,digits/3 exten=1234,n,Playback,digits/4 exten=1234,n,Rpt,1234|P I replaced the secret with a pw, and exten with my node 28344 added a line for username=.... My sip client says Request timeout, using the local wifi network to connect. so not a router issue... I have tried a few combinations... Any ideas? Thanks, Mark, KC7DMF

3 2

Back from the hospital
by Jim Duuuude 09 Jul '13

09 Jul '13

Ive been in the hospital for 3 days. I went in at 3AM because I woke up with SEVERE abdominal distention. Fortunately, there doesn't seem to be anything permanently wrong with me. It could even have been from some sort of non-infectious foreign matter in something I ate. Who knows. They certainly don't. Anyway, please give me a couple of days to recover and get "back on track". One rather obvious thing that needs dealing with is the strange things going on with the PayPal Autopatch subscriptions (gee, this should be "really fun"). Thanks.. Jim, WB6NIL

2 1

Radio with iaxclient
by John Locke 08 Jul '13

08 Jul '13

Hi all. I have installed a private node with a URI connected to a iCOM radio. I can connect to my asterisk with some standard iax softphones, like http://sourceforge.net/projects/kiax/. But this iax clients are for phones, not for radios. There is no PTT support. I'm trying to develop my own softphone with the http://sourceforge.net/projects/iaxclient library, but I can't find any documentation about radio management with iaxclient. Any advice would be very appreciated. Thanks in advance. John

1 2

Re: [App_rpt-users] Computing Hardware....
by Doug Crompton 08 Jul '13

08 Jul '13

James, I too would like to see the simple USB work on the Pi. The problem is that apparently the version of Asterisk that is in the Pi repository is newer and not compatible with app-rpt. If this really is the case then I ask why are we not making apt-rpt compatible with newer asterisk code. I find answers on apt-rpt regarding this are at times ellusive. There is code that works on the Beagleboard XM but I was also holding off for the Beaglebone black or some other cheaper board. RasPBX runs on both the Pi and the Beagle black - http://www.raspberry-asterisk.org/ I wonder if there are any splinter groups working on any of these projects and if so how could we contribute. 73 Doug WA3DSP http://www.crompton.com/hamradio > Date: Sun, 7 Jul 2013 13:57:57 +0100 > From: jrh(a)g0fhm.co.uk > To: app_rpt-users(a)ohnosec.org > Subject: [App_rpt-users] Computing Hardware.... > > Guys, > > The old laptop that I use on my node is just about ready to roll over > and die (numerous SMART warnings, and it's getting extremely hot). > > I'm looking for new hardware options. > > Any suggestions? In an ideal world, I would like to use my Pi with > simpleusb (PL is handled by radio with hardware COR), but from reading > the archives, it's been said that it is likely to never happen. Has > anyone actually used a Pi & made it work? > > Or, what about a Thin Client? > > I haven't got that much money to splash on new stuff, and I need > something with a low (ish) power consumption. > > Any ideas would be appreciated! > > Cheers, > > James G0FHM > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >

1 0

Paypal Autopatch stuff went a little "Bonkers"
by Jim Duuuude 07 Jul '13

07 Jul '13

I have no idea why, but the Allstar Autopatch profiles stated getting "suspended" for no apparent reason. I will have to look into this. Jim

1 0