June 2013 - App_rpt-users - lists.keekles.org

URI<>TKR-750 cable
by Jay Urish 06 Feb '15

06 Feb '15

Does anybody have notes on connecting tkr750 to a URI? TIA, W5GM

4 3

Registration issues
by Randy Ballard 07 Dec '13

07 Dec '13

My nodes 27365 and 27751 both on same server is showing on the status page but not showing in the rpt_extnodes on other nodes im using standard port 4569. we have been seeing this with several nodes in our group over past month or so of coarse if we define in the rpt file we can connect but would be nice if it was registering. sometimes it may show up in a few hours or a day generally a reboot and its gone again Thanks for any help in advance 73 Randy KB3HJC

5 9

Compile Errors
by Robert Garcia 28 Sep '13

28 Sep '13

Guys, I am working on compiling app_rpt for another platform using the sources from svn and following the makefile. It looks like I am going to need some help as I am already stuck at configuring zaptel. lol gcc -o menuselect menuselect.o strcompat.o menuselect_stub.o mxml/libmxml.a mxml/libmxml.a make[2]: Leaving directory `/home/tc/zaptel/menuselect' make[1]: Leaving directory `/home/tc/zaptel/menuselect' *********************************************************** The existing menuselect.makeopts file did not specify that 'zttool' should not be included. However, either some dependencies for this module were not found or a conflict exists. Either run 'make menuselect' or remove the existing menuselect.makeopts file to resolve this issue. *********************************************************** make: *** [menuselect.makeopts] Error 255 I then nuked the menuselect.makeopts per the error and tried again, I get a little further before receiving this error. make -C /lib/modules/3.0.21-tinycore/build ARCH=i386 SUBDIRS=/usr/src/zaptel/kernel HOTPLUG_FIRMWARE=yes KBUILD_OBJ_M="zaptel.o ztdummy.o ztdynamic.o zttranscode.o " modules make[2]: Entering directory `/usr/local/src/linux-headers-3.0.21-tinycore' CC [M] /usr/src/zaptel/kernel/zaptel-base.o In file included from /usr/src/zaptel/kernel/zaptel-base.c:37:0: /usr/src/zaptel/kernel/zconfig.h:26:28: fatal error: linux/autoconf.h: No such file or directory compilation terminated. make[3]: *** [/usr/src/zaptel/kernel/zaptel-base.o] Error 1 make[2]: *** [_module_/usr/src/zaptel/kernel] Error 2 make[2]: Leaving directory `/usr/local/src/linux-headers-3.0.21-tinycore' make[1]: *** [modules] Error 2 make[1]: Leaving directory `/usr/src/zaptel' make: *** [all] Error 2 make: Leaving directory `/usr/src/zaptel' Oddly, the linux/autoconf.h file is there, so I'm not sure what path is the base. I "fixed" that by providing an absolute path to the autoconf.h file. Then I tried again and received this. make -C /lib/modules/3.0.21-tinycore/build ARCH=i386 SUBDIRS=/usr/src/zaptel/kernel HOTPLUG_FIRMWARE=yes KBUILD_OBJ_M="zaptel.o ztdummy.o ztdynamic.o zttranscode.o " modules make[2]: Entering directory `/usr/local/src/linux-headers-3.0.21-tinycore' CC [M] /usr/src/zaptel/kernel/zaptel-base.o /usr/src/zaptel/kernel/zaptel-base.c: In function 'zt_rbs_sethook': /usr/src/zaptel/kernel/zaptel-base.c:2160:2: warning: suggest parentheses around operand of '!' or change '&' to '&&' or '!' to '~' [-Wparentheses] /usr/src/zaptel/kernel/zaptel-base.c: At top level: /usr/src/zaptel/kernel/zaptel-base.c:7650:2: error: unknown field 'ioctl' specified in initializer /usr/src/zaptel/kernel/zaptel-base.c:7650:2: warning: initialization from incompatible pointer type [enabled by default] /usr/src/zaptel/kernel/zaptel-base.c:7650:2: warning: (near initialization for 'zt_fops.fsync') [enabled by default] make[3]: *** [/usr/src/zaptel/kernel/zaptel-base.o] Error 1 make[2]: *** [_module_/usr/src/zaptel/kernel] Error 2 make[2]: Leaving directory `/usr/local/src/linux-headers-3.0.21-tinycore' make[1]: *** [modules] Error 2 make[1]: Leaving directory `/usr/src/zaptel' make: *** [all] Error 2 make: Leaving directory `/usr/src/zaptel' Any ideas on how I can get past this? Robert N5QM

3 7

Radio with iaxclient
by John Locke 08 Jul '13

08 Jul '13

Hi all. I have installed a private node with a URI connected to a iCOM radio. I can connect to my asterisk with some standard iax softphones, like http://sourceforge.net/projects/kiax/. But this iax clients are for phones, not for radios. There is no PTT support. I'm trying to develop my own softphone with the http://sourceforge.net/projects/iaxclient library, but I can't find any documentation about radio management with iaxclient. Any advice would be very appreciated. Thanks in advance. John

1 2

Small System Recommendations
by Robert Garcia 04 Jul '13

04 Jul '13

All, I am looking for recommendations on small, preferably inexpensive, systems that are capable of running on 12v to take advantage of the redundant power systems at our sites. I would like it to support at least two nodes running simpleusb as I don't need the DSP processing capabilities. The idea is that these systems would be connected to a port on an existing controller. I expect that HP thin clients are going to be my best bet, but there seem to be many different models so I don't know where to begin. Suggestions or thoughts? Robert N5QM

6 13

Interfacing Motorola TRBO XPR 4350 to BeagleBoard?
by Michael Wolthuis 01 Jul '13

01 Jul '13

I think I read someone has interfaced a TRBO XPR radio. Can you assist me with where you grabbed the TXA, RXA, COR and PTT? Did you get them off the connector on the back of the radio? I don't see the appropriate pinouts to configure as these in CPS? Thanks, Mike kb8zgl

3 2

internet connection problems
by The Rices 30 Jun '13

30 Jun '13

Hi, I have installed a Acid build on a computer and while testing we noticed that the computer would lose internet connections and cease to operate. After trying numerous different things to no avail I installed Mozilla and opened a browser so that it would have a open window to a web site I have. Since doing that it has not lost internet connections. Now the setup here is that I have a router that normally assigns an ip but to keep the allstar computer operating with a IP that I could assign forwarded ports I assigned it an ip above the range that the router would use. The allstar computer does look at the router for DNS after I found that it would not work when trying to go to the DNS of my provider. Anybody have any suggestions about what to look for so I don’t have to have a browser window open? Thanks Steve N4YZA

1 0

VMware Player WORKS!
by Jim W7RY 27 Jun '13

27 Jun '13

I just downloaded VMware player and installed it onto my win 7 HP laptop. Then I loaded CentOS and Asterisk from my ISO image CD. I’m using the URI... and it WORKS PERFECTLY! I can log into it with putty, and WINscp as well via the win 7 laptop that it’s running on. Pretty slick! Now installing it on my other HP Win 7 laptop. 73 Jim W7RY 28181 28343

1 0

Anyone Virtualizing?
by Jonathan Weirmeir 26 Jun '13

26 Jun '13

Hi, group! I'm new to app_rpt RoIP, coming from a background with IRLP. I'm wondering if anyone has ever tried virtualizing AllStar, and if so, were there any issues. Thanks! Jonathan On Jun 23, 2013 10:39 PM, "Benjamin L. Naber" <Benjamin(a)kb9lfz.com> wrote: > Robert, > > I am using a Neoware CA-22. It is both server and node on one machine. I > do not have any other machines for my allstar node. While watching top, > the CPU has yet to get busier than 0.4. It is using DSP for audio, and > runs without fail. > > It has 12Vdc input with a standard barrel plug. Not sure what the low > voltage cut-off is, but it runs fine on a SLA battery that just came > from an auto charger that goes to float after bulk charging brings it up > to 14.1V. The current draw varies, usually above 500mA at idle, and > about 750mA when I'm talking to or listening on the node. > > It has a 1GHz processor, 1GB RAM and 1GB flash drive. I used what I had, > but you will have space left over if you are only able to get 512MB RAM > and 512MB flash. > > I don't remember if I am using Limey Linux for VIA or i686. I am > thinking it's the for for i686 as I tried loading other linux distros > for VIA on there before I got into allstar and they just plain sucked > and didn't work for garbage. > > ~Benjamin, KB9LFZ > allstar node 28569 > > > On Sun, 2013-06-23 at 20:50 -0500, Robert Garcia wrote: > > All, > > > > I am looking for recommendations on small, preferably inexpensive, > > systems that are capable of running on 12v to take advantage of the > > redundant power systems at our sites. > > > > I would like it to support at least two nodes running simpleusb as I > > don't need the DSP processing capabilities. The idea is that these > > systems would be connected to a port on an existing controller. > > > > I expect that HP thin clients are going to be my best bet, but there > > seem to be many different models so I don't know where to begin. > > > > Suggestions or thoughts? > > > > Robert > > N5QM > > _______________________________________________ > > App_rpt-users mailing list > > App_rpt-users(a)ohnosec.org > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >

8 9

VBox !!
by Ian Wilson 26 Jun '13

26 Jun '13

I tried it and found that I couldn't get the audio to perform consistently, would work sometimes and not others. Ubuntu 12.04 Virtual Box URIx 73, Ian..

1 0