July 2010 - App_rpt-users - lists.keekles.org

SheevaPlug
by Monty Dana 03 Jan '12

03 Jan '12

Anyone ever try to run app_rpt on the SheevaPlug <http://plugcomputer.org/>? -- Monty

4 3

Re: [App_rpt-users] CLI (Command Line Interface)
by Craig Hastings 26 Jul '10

26 Jul '10

Thanks Bob! On 26 July 2010 12:29, Bob Brown - WØNQX <bbrown(a)byrg.net> wrote: > rpt fun yournodenumber *xx > and this list should get you going > > http://app-rpt.qrvc.com/node/21 > > > This section contains the suggested prefix digits, mandatory command codes, > and suggested command codes for Allstar Link. > > > Prefix Digit Suggestions Prefix Functions *1 Disconnect Link *2 Monitor > Link *3 Connect Link *4 Command Mode *5 Macros *6 User Functions *7 Connection > Status *8 User Functions *9 User Functions *0 User Functions *A User > Functions *B User Functions *C User Functions *D User Functions > > > Mandatory Command Codes > These are the mandatory command codes which all Allstar Link nodes must > support to provide command code consistency to the users. Command Code Description > *1node Disconnect Link *2node Connect link in monitor mode *3node Connect > link in transcieve mode *4node Enter command mode on a remote node *7 Local > connection status > > > Notes > > > 1. node is an Allstar Link node number > 2. Node number zero (0) is shorthand for the last node operated on by a > previous command > 3. Monitor mode means listen to a node, but do not send any audio to it > > 4. Command mode means send all received DTMF digits to the node number > specified (bypassing the local command decoder). Send # to exit command > mode, and restore local command decoding. > > > Optional Command Codes Command Code Description *80 Force System ID *81 Say > System Time *82 Say app_rpt software version *85 Last active node > (system-wide) *87 System-wide connection status *51 Disconnect all links > (macro) *52 Site Normal (macro) *53 Reconnect all links (macro) > > > -- > Thanks in Advance > > Bob Brown, WØNQX > > Kansas City Metro Area > > http://sm0kenet.net > > http://byrg.net > > http://kcdstar.byrg.net > > Quis custodiet ipsos custodes? > > -- > > > > On Mon, Jul 26, 2010 at 11:03, Craig Hastings <craig.hastings(a)gmail.com>wrote: > >> >> Does anyone have a list of Command line interface stuff specifically how >> to control the node from the command line. I am guessing this would be from >> the 'asterisk -r' command line. >> >> Say a Link is Up and I want to take it down or put up a link from the >> command line, I hunted around and didn't find anything on it, sorry if its >> posted already somewhere however I have only looked a few months back in the >> archives. >> >> Thanks. >> >> Craig >> VA3DTF >> VE3WOM-L echolink & allstar >> >> >> >> >> >> _______________________________________________ >> App_rpt-users mailing list >> App_rpt-users(a)qrvc.com >> http://qrvc.com/mailman/listinfo/app_rpt-users >> >> >

1 0

CLI (Command Line Interface)
by Craig Hastings 26 Jul '10

26 Jul '10

Does anyone have a list of Command line interface stuff specifically how to control the node from the command line. I am guessing this would be from the 'asterisk -r' command line. Say a Link is Up and I want to take it down or put up a link from the command line, I hunted around and didn't find anything on it, sorry if its posted already somewhere however I have only looked a few months back in the archives. Thanks. Craig VA3DTF VE3WOM-L echolink & allstar

1 0

Re: [App_rpt-users] Problems running Echolink
by Craig Hastings 26 Jul '10

26 Jul '10

Hello Eric, I did not see anyone answer you, I had this problem as well. you need to update your echolink.conf file I put these servers in and remove the ones you have now. server1=naeast.echolink.org server2=nasouth.echolink.org server3=servers.echolink.org The default servers don't resolve correctly and you should point at the ones closest to you, You can also get away with using only the closest one to you which would keep down on the traffic I think. NA east is the closest server to us. Hope this helps. Craig VA3DTF Node Master for VE3WOM-L (allstar) & Echolink VE3WOM-R Echolink & IRLP 2255 ----- Original Message ----- From: Eric Meth To: App_rpt-users at qrvc.com Sent: Sunday, June 20, 2010 10:27 PM Subject: Problems running Echolink I operate 3 app-rpt nodes, 2344, 2425 and 2579 Node 2344 has the following problem on echolink, from the /var/log/asterisk/messages log [Jun 20 19:16:07] NOTICE[11013] chan_echolink.c: Received OK from Echolink server server2.echolink.org [Jun 20 19:16:07] ERROR[11013] chan_echolink.c: Error in parsing header on server2.echolink.org [Jun 20 19:16:27] NOTICE[11013] chan_echolink.c: Received OK from Echolink server server3.echolink.org [Jun 20 19:16:27] ERROR[11013] chan_echolink.c: Error in parsing header on server3.echolink.org Anyone able help debug this problem? Eric Meth - ve3ei

1 0

Re: [App_rpt-users] CM-108 or CM-119 source
by Stu Williams 25 Jul '10

25 Jul '10

http://www.dealextreme.com/search.dx/search.cm108 $6.99 have used them and had no problem. VK4SZ

1 0

Looking for CM-108 or CM-119 fobs
by Yokshs 25 Jul '10

25 Jul '10

Hello, I'm looking for a couple of CM-108 or CM-119 sound fobs that can be modified for Asterisk/Allstar use. If you have a few to sell, or know of a source,. please reply to me directly. Thanks, 73. Kyle K0KN

1 0

Identifier update
by Chuck Kraly 24 Jul '10

24 Jul '10

Ok, here is the latest We are running 0.255 and no matter where the key up comes from (rf, IAX) the talkover id runs, in the middle a CT sounds, and then the Initial ID runs. Our talkover is cw, and the initial is voice. Our group was discussing it and we have noticed it just started showing up in the later builds. When we are not sure..... Chuck K0CMK

3 2

Re: [App_rpt-users] can App_Rpt decode SAME weather codes?
by David KE6UPI 23 Jul '10

23 Jul '10

First look at this link. http://www.cfreeze.com/trac/stormsiren/ This might make writing the code easier. Hey Kan, Sorry if my last email was a little hard. Yep I under stand that you want the S.A.M.E. alert to trigger a different courtesy tone. I don't write the code for APP_RPT but lets look at what you and others would want for the S.A.M.E. alert. When the S.A.M.E. alert is triggered 1) Record the alert so it can be played back by a dial plan or connect to a Rx radio with updated info. 2) Connect to a node and Tx the audio alert (maybe use a different PL code) 3) Text to speech for the coded message. 4) Program more then one S.A.M.E. alert code 5) Allow admins to configure S.A.M.E. alert code to connect to different nodes. 6) Change courtesy tones. 7) Play coded message any 1-10 minutes. (TORNADO) 10) Dial plan to reset S.A.M.E. alert. May guess is that if you have a S.A.M.E. alert radio and URI I would try to fine the COS or COR and just play with that first. I would think that you should be able to find a S.A.M.E. alert radio that has output for COS or COR and the TEXT data. If you have that I think you could make it very simple for the code writers. On Fri, Jul 23, 2010 at 8:54 AM, Ken <ke2n(a)cs.com> wrote: > We get some very localized storms here and my repeater mainly covers 2 > counties whereas, the local NWS transmitter (MAN) covers ~15 counties > > > > http://www.erh.noaa.gov/lwx/nwr/nwrmap.htm > > > > … but more than that, I would like the repeater courtesy tone, or tail > message, to change when an alert is active. And it should state what the > problem is: ‘severe thunderstorm warning’ or ‘tornado watch’ and so forth. > > > > This is important because the NWS just triggers the alarm once and leaves > it up for several hours. If you missed the initial message, you are out of > luck. And I don’t want to listen to the weather 24/7 – only to be advised > when something is about to hit. > > > > There was another machine around here with an RLC controller and one of > those $500 CAT weather radios that did exactly this. Asterisk should be > smart enough to do the same. It is always looking for DTMF digits, it should > be able to find SAME codes … > > > > 73 > > Ken > > > > > > > > > > *From:* shawpbx(a)gmail.com [mailto:shawpbx@gmail.com] *On Behalf Of *David > KE6UPI > *Sent:* Friday, July 23, 2010 11:16 AM > > *To:* Ken > *Subject:* Re: [App_rpt-users] can App_Rpt decode SAME weather codes? > > > > Yes Ken I understand how S.A.M.E. works, but don't see how a wide area > repeater would care. I was thinking of using S.A.M.E. on my repeater and > found that I get the same S.A.M.E. info for all of the San Diego county > area. Not just one little area. So playing around with a NWR radio hooked up > to a URI did work, I couldn't find any real use for it. If you going to > leave your Ham radio on next to your bed to listen to your repeater with the > weather alert you might as well use a S.A.M.E. radio. > > David > > On Thu, Jul 22, 2010 at 2:13 PM, Ken <ke2n(a)cs.com> wrote: > > SAME is the protocol that NWR uses > > > > We are looking for more than just an alert tone, but actually the data that > tells you what area the warning is for – > > It is AFSK - like packet radio > > > > http://en.wikipedia.org/wiki/Specific_Area_Message_Encoding > > > > Ken > > > > > > > > > > *From:* shawpbx(a)gmail.com [mailto:shawpbx@gmail.com] *On Behalf Of *David > KE6UPI > *Sent:* Thursday, July 22, 2010 4:50 PM > *To:* Ken > > > *Subject:* Re: [App_rpt-users] can App_Rpt decode SAME weather codes? > > > > Would it be easyer to use NWR then S.A.M.E. NWR uses 1050hz tone. Or buy a > cheap S.A.M.E. radio and find a the cos or cor. > > http://www.nws.noaa.gov/nwr/same.htm > > The Kenwood TM-271 has the NWR built in. > > David > > On Thu, Jul 22, 2010 at 12:37 PM, Ken <ke2n(a)cs.com> wrote: > > Well - there is a windoz program that does it > > > > http://www.brothersoft.com/tonedecoder.net-standard-edition-211249.html > > > > but it is rather pricy ... apparently it is hard to do ... > > > > > > Ken > > > > > > -----Original Message----- > From: Jim Duuuude <telesistant(a)hotmail.com> > To: jrorke(a)cogeco.ca; app_rpt mailing list <app_rpt-users(a)qrvc.com> > Sent: Thu, Jul 22, 2010 2:28 pm > Subject: Re: [App_rpt-users] can App_Rpt decode SAME weather codes? > > > as opposed to DIFFERENT weather alert protocol... > or perhaps SIMILAR..... :-) :-) > > JIM WB6NIL > > Date: Thu, 22 Jul 2010 13:12:14 -0400 > > From: jrorke(a)cogeco.ca > > To: app_rpt-users(a)qrvc.com > > Subject: [App_rpt-users] can App_Rpt decode SAME weather codes? > > > > Hi All just wondering if App_Rpt can or does support of decoding the > > SAME weather alert protocol and signaling?? > > > > Thanks, > > > > Jon VA3RQ > > > > > > _______________________________________________ > > App_rpt-users mailing list > > App_rpt-users(a)qrvc.com > > http://qrvc.com/mailman/listinfo/app_rpt-users > > = > > _______________________________________________ App_rpt-users mailing list App_rpt-users(a)qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users > > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)qrvc.com > http://qrvc.com/mailman/listinfo/app_rpt-users > > > > >

1 0

can App_Rpt decode SAME weather codes?
by Jon Rorke 22 Jul '10

22 Jul '10

Hi All just wondering if App_Rpt can or does support of decoding the SAME weather alert protocol and signaling?? Thanks, Jon VA3RQ

4 4

Re: [App_rpt-users] can App_Rpt decode SAME weather codes?
by Jon Rorke 22 Jul '10

22 Jul '10

I guess its not supported. (SAME-Specific Area Message Encoding) Ok I was just wondering. I have a S.A.M.E. decoder board from Cat controllers. its the WD-100. http://www.catauto.com/wd100.html I'm going to wire it up to a VHF GE Phoenix. And connect it to a Ast node fob. This way it has a little more smarts in the decoder but what we need is some hardware I/O control from the AST box. Is there any hardware I/O supported in App _Rpt like parallel pin twiddling or serial port pins? I think the decoder can be controlled via DTMF so maybe get the node to generate DTMF commands as macros. I'll let you know how I make out. Jon > as opposed to DIFFERENT weather alert protocol... > or perhaps SIMILAR..... :-) :-) > > JIM WB6NIL > > Date: Thu, 22 Jul 2010 13:12:14 -0400 > > From: jrorke(a)cogeco.ca > > To: app_rpt-users(a)qrvc.com > > Subject: [App_rpt-users] can App_Rpt decode SAME weather codes? > > > > Hi All just wondering if App_Rpt can or does support of decoding the > > SAME weather alert protocol and signaling?? > > > > Thanks, > > > > Jon VA3RQ

1 0