March 2014 - App_rpt-users - lists.keekles.org

RTCM Setup Questions
by ssedgwick 09 Mar '14

09 Mar '14

I have a thru hole version of the voter board and have a few questions: 1. Should the yellow host LED be flashing or on solid? Mine is flashing 2. Should the red transmitter LED be flashing or on solid when transmitting? Mine is flashing at the same rate as the yellow host LED. 3. When I telnet into the RTCM I get the following scrolling over and over. I don't have master in the voter.conf file so I don't understand why it keep saying "ERROR! Host not acknowledging non-GPS disciplined operation" <System Time Not Set> Host Connection established (Pri) (192.168.1.195) <System Time Not Set> ERROR! Host not acknowledging non-GPS disciplined operation <System Time Not Set> Host Connection Lost (Pri) (192.168.1.195) <System Time Not Set> Host Connection established (Pri) (192.168.1.195) <System Time Not Set> ERROR! Host not acknowledging non-GPS disciplined operation <System Time Not Set> Host Connection Lost (Pri) (192.168.1.195) <System Time Not Set> Host Connection established (Pri) (192.168.1.195) <System Time Not Set> ERROR! Host not acknowledging non-GPS disciplined operation Here is my voter.conf file [general] port=667 buflen=500 password=ima516 [27761] client1=radios,transmit I have the rpt.conf change from: rxchannel=Radio/usb27761 to: rxchannel=voter/27761 Any ideas? Thanks, Steve_WB8GRS

2 2

Re: [App_rpt-users] app_rpt script execution
by mike＠midnighteng.com 09 Mar '14

09 Mar '14

2 1

Re: [App_rpt-users] DTMF A B C D
by mike＠midnighteng.com 09 Mar '14

09 Mar '14

5 4

RTCM PTT circuit
by Bryan Fields 09 Mar '14

09 Mar '14

I'm interfacing the RTCM with a hamtronics exciter and will be using a small relay to key it. Can it sink 100 ma to ground for the relay or do I need a driver transistor? -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net

7 6

Hamtronics (was Re: RTCM PTT circuit)
by Bryan Fields 08 Mar '14

08 Mar '14

On 3/8/14, 11:57 AM, Sam Nabkey wrote: > I totally agree... I had a Hamtronics 220 repeater and I did exactly that... > > After the audio mods it sounded really nice. Since asterisk generates the ctcss, and will do limiting/processing, why would you not feed it into the modulator directly? The newer hamtronics PLL exciter boards are quite good. They don't do them as a kit anymore so build issues are not a problem (dear god how they were!) They are all SMT for the most part (less/no microphonics), and they switched the final transistor from case-collector to a case emitter (BeO insulated) so the final transistor does not have RF on the case anymore. It's direct FM, not PM. The only thing I use the amp/limiter for is the local mic, and I'm not going to be doing local mics on my repeaters going forward. All this said, hamtronics needs a small (BRASS) box they can sell to mount the boards in. I've made one out of PCB but it's not perfect and quite ugly. I detest wires soldered to the boards in an enclosure so I use some header pins and solder those to the feed-through filters between the segments. I remove the stupid phono connectors and put a proper SMA in place, and convert the unit so the PLL is always powered. Box Pics (SFW) http://gallery.keekles.org/d/28340-2/0308140155.jpg http://gallery.keekles.org/d/28343-2/0308140155b.jpg http://gallery.keekles.org/d/28337-2/0307141213.jpg The units are fairly trivial to sync to 10MHz, Put a SMA on the board and put a .1 uF chip cap in line where the TXCO used to be. I rip out the uP and dip switches and they are not needed (I'd asked hamtronics to modify their code to change R from /2048 to /2000 and they said it was going to take weeks and cost thousands to do it! Sucks but for $200 bux I got it going with a PIC 16f88). Couple this with a thunderbolt 10MHz GPSDO, and you have a frequency stability in the mHz (that's milihertz). Now I don't have a simulcast system online yet (working on the prime site now), but I expect everything should work. I could be wrong and have already been a few times, but it's a big experiment :) There are few commercial 220 repeaters out there, and even fewer that can take an external 10 MHz reference. You can convert/buy a micor to 220, but it's a 40 pound and 50 year old radio. By time you add in the cost of proper channel elements from ICM it's not worth it. The hamtronics exciter/receiver are "pure"; no extra crap, no stupid motorola design issues, if you need to modify it it's easy to get at basic parts. It's the basic building blocks, and no more. Sorry for the teal deer, but it's my thoughts on the subject as I take some shit for being a hamtronics supporter. -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net

1 0

Re : RTCM PTT circuit
by pete M 08 Mar '14

08 Mar '14

Using a transistor would be wise even if the rtcm can do it. Its simpler to replace a 22222 then to fix a rtcm if something goes wrong . --- Message initial --- De : "Bryan Fields" <Bryan(a)bryanfields.net> Envoyé : 7 mars 2014 17:52 A : app_rpt-users(a)ohnosec.org Objet : [App_rpt-users] RTCM PTT circuit I'm interfacing the RTCM with a hamtronics exciter and will be using a small relay to key it. Can it sink 100 ma to ground for the relay or do I need a driver transistor? -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

1 0

Re: [App_rpt-users] USB URIx overmodulation problem?
by Johnny Keeker 08 Mar '14

08 Mar '14

Assuming one knows about the rxboost=x setting in the usbradio.conf. The URI has 2 audio inputs, pin 21 and pin 9. Pin 21 is padded, pin 9 is not. Motorola's work well on pin 21, but occasionally it may be necessary to use pin 9 along with some minor modifications to properly adjust rx audio. In this case, look at the RIM from repeater builder. It has only one audio input and a selectable audio input attenuator. You don't need any extra parts or mods. Their input attenuator works well with a URI. The RIM has some other unique advantages one might consider. JK -------------------------------------------- On Thu, 3/6/14, Kevin Oleniczak <n9jpg.ham(a)gmail.com> wrote: Subject: [App_rpt-users] USB URIx overmodulation problem? To: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> Date: Thursday, March 6, 2014, 12:17 AM I'm using a URIx module with my radio and am in the process of adjusting audio levels. I'm following the well documented procedures to set rx and tx levels but noticed that that choices in txvoice levels have little or no effect. I've made some measurements with my service monitor. radio tune txvoice 10 >> 0.35Khz deviation radio tune txvoice 14 >> 4.8Khz deviation radio tune txvoice 15 >> 4.8Khz deviation radio tune txvoice 20 >> 5.2Khz deviation radio tune txvoice 100 >> 5.2Khz deviation radio tune txvoice 500 >> 5.2Khz deviation radio tune txvoice 900 >> 5.2Khz deviation With a goal of 3KHz deviation, its not possible through settings alone. Any ideas why this is so touchy? thanks -----Inline Attachment Follows----- _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

3 2

Voter Question- Thru Hole Version
by ssedgwick 08 Mar '14

08 Mar '14

Hi, I believe this is my first post I got my thru-hole version of the voter board built and the latest firmware loaded. When I telnet into the voter I get continuous scrolling of the following message: <System Time Not Set> Host Connection Lost (Pri) (96.36.57.202) <System Time Not Set> Host Connection established (Pri) (96.36.57.202) <System Time Not Set> ERROR! Host not acknowledging non-GPS disciplined operation <System Time Not Set> Host Connection Lost (Pri) (96.36.57.202) <System Time Not Set> Host Connection established (Pri) (96.36.57.202) <System Time Not Set> ERROR! Host not acknowledging non-GPS disciplined operation My question is, how do I stop the scrolling so I can edit the items in the main menu such as the Voter Server Address FQDN? Thanks, Steve_WB8GRS

2 2

USB FOB options
by Steve Wright 07 Mar '14

07 Mar '14

snarl.. just bought two CM-119 USB FOBs locally and they're potted... tempted to fling them in the bin.. growl... Paint stripper, heat, and solvent won't get this snot off.. cue FBH but hey I have self control!!!! Ok what are my options? This old POS 1990's computer has a parallel port. Maybe easier to just get the proper USB FOB from elsewhere than hax0r up some parallel port lovin, but not keen on the absurd freight from the US. Suggestions? sigh. -- Meshnetworks - Rangitaiki Plains Rural Broadband Internet Providers +64 21 040 5067

6 5

Re: [App_rpt-users] XIPAR Allstar Password where is it stored
by Brian Burton 07 Mar '14

07 Mar '14

First of all, the secret in iax_rpt_custom.conf refers to the password used by iax_rpt control op client to connect to your node... I recommend NOT using your root login password or the password assigned to your node number by allstarlink.org... this can be any password of your choosing.. Node number and password for registration of allstar on Xipar is stored in iax_registration_custom.conf ex: register=nodenumber:password@register.allstarlink.org Connection refused sounds like you do not have port forwarding set up properly.. Check your router or firewall to be sure that you have the iax port that you assigned on allstarlink.org forwarded to your server. 4569 is usually the default used, however some ISP's do block that port. You may have to switch to another port above or below. On Thu, Mar 6, 2014 at 10:37 PM, <app_rpt-users-request(a)ohnosec.org> wrote: > Send App_rpt-users mailing list submissions to > app_rpt-users(a)ohnosec.org > > To subscribe or unsubscribe via the World Wide Web, visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > or, via email, send a message with subject or body 'help' to > app_rpt-users-request(a)ohnosec.org > > You can reach the person managing the list at > app_rpt-users-owner(a)ohnosec.org > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of App_rpt-users digest..." > > > Today's Topics: > > 1. incoming allstar connections fail (Greg) > 2. Re: incoming allstar connections fail (Doug Crompton) > 3. Re: USB FOB options (Steve Wright) > 4. Re: USB FOB options (Andrew Errington) > 5. Re: USB FOB options (Kevin Custer) > 6. XIPAR Allstar Password where is it stored? (Joe Bennett) > 7. Re: incoming allstar connections fail (Doug Crompton) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Thu, 06 Mar 2014 12:28:12 -0500 > From: Greg <kb1ncj(a)gmail.com> > To: app_rpt-users(a)ohnosec.org > Subject: [App_rpt-users] incoming allstar connections fail > Message-ID: <5318B02C.5030100(a)gmail.com> > Content-Type: text/plain; charset=ISO-8859-1; format=flowed > > I can't figure out why.. I have port 4569 forwarded and echolink works > fine with it's needed ports forwarded. I am trying to test using the web > transceiver. A friend of mine can't connect to my node from his Allstar > node either. Am I blocked from my own node using the web transceiver? > Thanks for any help.. > Greg > > > ------------------------------ > > Message: 2 > Date: Thu, 6 Mar 2014 12:43:00 -0500 > From: Doug Crompton <doug(a)crompton.com> > To: Greg <kb1ncj(a)gmail.com> > Cc: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> > Subject: Re: [App_rpt-users] incoming allstar connections fail > Message-ID: <BLU172-W27E14E56FCFE2ECD212493BA880(a)phx.gbl> > Content-Type: text/plain; charset="iso-8859-1" > > > Do you have the web transceiver access enabled on your node access > settings at allstarlink.org? Can others connect to you allstar node to > node? What is your node number? > > > 73 Doug > WA3DSP > http://www.crompton.com/hamradio > > > > Date: Thu, 6 Mar 2014 12:28:12 -0500 > > From: kb1ncj(a)gmail.com > > To: app_rpt-users(a)ohnosec.org > > Subject: [App_rpt-users] incoming allstar connections fail > > > > I can't figure out why.. I have port 4569 forwarded and echolink works > > fine with it's needed ports forwarded. I am trying to test using the web > > transceiver. A friend of mine can't connect to my node from his Allstar > > node either. Am I blocked from my own node using the web transceiver? > > Thanks for any help.. > > Greg > > _______________________________________________ > > App_rpt-users mailing list > > App_rpt-users(a)ohnosec.org > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > > To unsubscribe from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down > to the bottom of the page. Enter your email address and press the > "Unsubscribe or edit options button" > > You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message to > the list detailing the problem. > > > >

2 1