- App_rpt-users - lists.keekles.org

lat/lon
by Ken 23 Aug '10

23 Aug '10

I have two servers that I entered at different times - the latitude and longitude on the allstarlink.org tabular (form) page looks OK, but the values are interchanged on one of the two nodes in the graphic status page, depending on how it is displayed one is swapped here (lat<->lon) - the two should be the same http://stats.allstarlink.org/getstatus.cgi?27021 here they are the same, but both are lat/lon swapped http://stats.allstarlink.org/getstatus.cgi?27061 I notice this on other people's nodes too, for example http://stats.allstarlink.org/getstatus.cgi?27200 Ken

1 1

Re: [App_rpt-users] node move
by Stephen Rodgers 23 Aug '10

23 Aug '10

Gary - K7EK wrote: > No. Not migrated. I'm still under the old system. > > > > On Sun, Aug 22, 2010 at 6:54 PM, Stephen Rodgers <sales(a)qrvc.com> wrote: > >> Gary - K7EK wrote: >>> Is there a way to create a node from the portal for re-installation? In >>> other words, I have two nodes which were registered a long time ago. I >> need >>> to re-install Asterisk before I can put them on the air. If I could use >> the >>> already registered node numbers from a portal installation, that would >> save >>> me a lot of time. Comments? >>> >>> Best regards, >>> >>> Gary, K7EK >>> >>> Personal Web Page: www.k7ek.net >>> >>> --- >>> >>> >>> On Sun, Aug 22, 2010 at 6:02 PM, REDBUTTON_CTRL <jrorke(a)cogeco.ca> >> wrote: >>>> Excellent ! works like a champ! >>>> Thanks, guys. >>>> Also have created a couple of nodes from the portal and downloaded to >>>> the boxes. >>>> Its actually quicker then doing it the old way! >>>> >>>> This is slick. >>>> >>>> Jon VA3RQ >>>> >>>> Jim Duuuude wrote: >>>>> For all of you who need to move a node from one server to another, we >>>>> now have the >>>>> capability built into the portal. >>>>> >>>>> See the 'Move Node To Another Server' in the 'Nodes' drop-down menu. >>>>> >>>>> JIM WB6NIL >>>>> >>>>> >>>>> >> ------------------------------------------------------------------------ >>>>> _______________________________________________ >>>>> App_rpt-users mailing list >>>>> App_rpt-users(a)qrvc.com >>>>> http://qrvc.com/mailman/listinfo/app_rpt-users >>>>> >>>> _______________________________________________ >>>> App_rpt-users mailing list >>>> App_rpt-users(a)qrvc.com >>>> http://qrvc.com/mailman/listinfo/app_rpt-users >>>> >>> >>> >>> >>> ------------------------------------------------------------------------ >>> >>> _______________________________________________ >>> App_rpt-users mailing list >>> App_rpt-users(a)qrvc.com >>> http://qrvc.com/mailman/listinfo/app_rpt-users >> Have they been migrated? >> >> > > To use remote configuration and setup from allstarlink.org: You must migrate the nodes, then under node configuration -> radio interface set the node type to anything but register only, then go ahead and adjust all other node settings to your liking. When you do the new install, choose download the configuration files from the server (Y) and follow the instructions, and your system should now be remotely configurable from allstarlink.org. Manual configuration: Node should be set up for register only. Jot down to the node password in the yellow node information box. Install the software, done choose config file download (N), and edit the configuration files to your liking. Steve WA6ZFT

1 0

node move
by Jim Duuuude 23 Aug '10

23 Aug '10

For all of you who need to move a node from one server to another, we now have the capability built into the portal. See the 'Move Node To Another Server' in the 'Nodes' drop-down menu. JIM WB6NIL

4 4

Node creation from portal?
by Gary - K7EK 23 Aug '10

23 Aug '10

Is there a way to create a node from the portal for the purpose of re-installation? In other words, I have two nodes which were registered a long time ago under the old system. I need to re-install Asterisk before I can put them on the air. If I could use the already registered node numbers from a portal installation, that would save me a lot of time. Comments? -- Best regards, Gary E. Kohtala - K7EK / AFA0IU / AFE0DM Personal Web Page: http://www.k7ek.net

1 0

node wont start with out internet
by REDBUTTON_CTRL 23 Aug '10

23 Aug '10

Hi All, I have a node that I recently setup with a static ip. It seems to be working fine but... If the ethernet cable is not plugged in and the node is rebooted Asterisk starts but the URIs are not running. Once I plug in the internet then the fobs start working. This node was built using the old system but the version of APp-Rpt is 0.255. If the cable is connected then it boots fine. Also I tried connecting to a switch with no internet connection and rebooted - same thing none of the USB interfaces were not working. Plugged the router in then the fobs start. If I disconnect internet the node works ok. Its just at boot up that it has this problem. Older nods didn't seem to care about the internet not connected. If I put the node on DHCP then it boot up ok and the fobs work. Any ideas? My concern is if this node is deployed and internet is lost with a power failure then the node will hang until internet is back. that would take down the repeater that it is planed to control. Jon

1 0

Skype
by Ken 22 Aug '10

22 Aug '10

I have "discovered" the Digium Skype-for-Asterisk product and wonder if it can be used with ACID? They say that version 1.4.25 of asterisk is required. Apparently ACID uses "1.4.23-pre" Is this going to be compatible? Ken KE2N

3 3

Email validation on allstarlink.org
by Stephen Rodgers 22 Aug '10

22 Aug '10

For some reason unbeknownst to us, some users are not receiving validation emails from allstarlink.org when they sign up for a new user account. We know the server is sending these out. For those users experiencing difficulty with this, I can do a manual validation. I just need to know who is having issues so I can send a validation request from my personal email account using your email address in the database. If you respond to the message, I'll manulally validate the account. Steve WA6ZFT

3 2

Node passwords for new nodes.
by Stephen Rodgers 22 Aug '10

22 Aug '10

Some users have reported there is no way to get node passwords for newly assigned nodes which are set up as register only. Jim, WB6NIL has fixed this. The node password is now displayed on the display/modify node information page. Steve WA6ZFT

1 0

Re: [App_rpt-users] Skype and newer versions of asterisk
by Jim Richardson 22 Aug '10

22 Aug '10

There an easy way to run whatever version of asterisk you want that also requires minimal changes in your allstarlink node setup, just some additions to iax.conf and extensions.conf. You do need to set up another computer for the newer asterisk. Then simply create an IAX trunk between your newer asterisk and your allstar node asterisk. I've migrated my node to the new system, I am in the process of changing my config files to the new system so I can use the Web Transceiver etc. I am changing extensions.conf as little as possible and inserting "#include iax_additional.conf" as the last line of the file so most of my changes are in this other file. I'm also going to use the same technique on iax.conf by "#include iax_additional.conf" as the last line of that file. I am running PBX In A Flash (PIAF) for my phone PBX and Limey Linux for my allstar node. I have been running this way for over a year. I have the ability to make and receive calls from Skype as well as PSTN, VOIP and ROIP. I simply call into my PIAF PBX from any of the above and dial my extension for the allstar node and now I can access my node. It also works the other way where my allstar node can dial an extension on my PIAF PBX and go out on any trunk be it Skype, VOIP, or PSTN. My motivation in doing it this way was the ability to use the GUI in PIAF to set up an IVR and all calls from anywhere get the ability to be routed to anywhere. I will post after I have finished my edits and tested my config. Jim WA1SOT Node 2370

1 0

Portal
by Bob Bunter 20 Aug '10

20 Aug '10

Wonder why when I ported 3 of my Nodes over to the New System everything was fine except my Node 27050 location is Blank? Should show as Santa Cruz, Ca.

1 0