December 2009 - App_rpt-users - lists.keekles.org

Device usb currently not active
by Paul 13 Dec '09

13 Dec '09

Hi, (Sorry if you receive this message more than once, the first two bounced.) I am new to asterisk and ROIP. I am trying to set up a test system for evaluation. I purchased 2 USB sound adapters that claim to be CM108 but I have NOT tried to modify them yet. I completed the installation, and connected the USB device when instructed. When I type radio tune I get the following: test*CLI> radio tune Active radio interface is [usb] Device String is Card is -1 Output A is currently set to composite. Output B is currently set to off. Tx Voice Level currently set to 500 Tx Tone Level currently set to 200 Rx Squelch currently set to 725 Usage: radio tune <function> rxnoise rxvoice rxtone rxsquelch [newsetting] txvoice [newsetting] txtone [newsetting] auxvoice [newsetting] save (settings to tuning file) load (tuning settings from EEPROM) All [newsetting]'s are values 0-999 When I type radio tune rxnoise I get: test*CLI> radio tune rxnoise Device usb currently not active <- Note: device usb not active test*CLI> radio active usb Tried this, still not active test*CLI> radio tune rxnoise Device usb currently not active How do I make it active? [root@test asterisk]# lsusb Bus 002 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 005 Device 001: ID 0000:0000 Bus 001 Device 001: ID 0000:0000 Bus 004 Device 002: ID 0c76:1607 JMTek, LLC. Bus 004 Device 001: ID 0000:0000 Is this because I have not modified the USB fob? Or, is it because it is not really a CM108? Is it possible to tell in software if it is a CM108? Thanks for your help, Paul

4 3

CLI Message
by kd7yat＠cox.net 12 Dec '09

12 Dec '09

I am having trouble controlling, each time I try the message from the asterisk CLI reads, " hungup 'zap/pseudo-(10 digit #) ' " What does this indicate? Thanks Ed

1 0

Voting receivers for app_rpt
by Mark Hergesheimer 09 Dec '09

09 Dec '09

I for one am happy with the current hardware selection and would not want to suffer reliability issues by adding IRLP, sound cards, etc. To say nothing of the burden on the people that put this stuff together. Having said that, is there a way to set up voting receivers with app_rpt? I've snooped around a bit but have not much mention of the subject. Or can somebody point me in the right direction. It would really be an asset for our 900 system in So Cal. Mark KD6WLY

1 0

Re: [App_rpt-users] usbradio similar driver with non usb
by Tony Langdon, VK3JED 08 Dec '09

08 Dec '09

At 04:56 AM 12/9/2009, hwstar(a)rodgers.sdcoxmail.com wrote: >Although sound cards and IRLP interfaces are what folks have, and >these folks don't want to invest in a whole new radio interface due >to the added costs, the developers feel that this is too much of a >burden on them and therefore have no inclination to open up support >for every sound card out there. As there is already software which supports sound cards and IRLP boards (and a bunch of Echolink interfaces), such as thelinkbox, perhaps improving the integration batween Asterisk and this sort of software would be worth doing. I'd certainly like to be able to integrate Asterisk smoothly with my linkbox based systems. The chan_rtpdir driver went a long way to doing this, but it had a few limitations, like being stuck with the GSM codec. I'm sure if a better interface was developed, Skip would be happy to support it in thelinkbox and thebridge. I know chan_echolink or chan_irlp could be used to make an audio link, but on some configurations, that requires some careful scripting to treat the internal link to Asterisk separately from any conventional IRLP or Echolink connections. 73 de VK3JED / VK3IRL http://vkradio.com

2 2

Re: [App_rpt-users] usbradio similar driver with non usb
by hwstar＠rodgers.sdcoxmail.com 08 Dec '09

08 Dec '09

> > From: "Yokshs" <yokshs(a)sbcglobal.net> > Date: 2009/12/08 Tue AM 09:04:21 PST > To: <app_rpt-users(a)qrvc.com> > Subject: Re: [App_rpt-users] usbradio similar driver with non usb > > > I made the changes to usbradio that you suggest about a year or so ago, and it worked ok. However I was just getting started with app-rpt, and > > there were some other little issues I was having. I decided to mod the cm108 device and see how that compared. Unless you're using the > > recommended hardware/software, it's really hard for anyone to help. > > > I'm also interested in such a driver. I'd really like to continue using my IRLP board, but I can't seem to make app-rpt work with it directly. > > 73, > > Kyle > K0KN > > As Jim Dixon stated previously, this is a can of worms about to be opened. If someone wants to offer support other than us, that is OK, but this project does not have the developer resources to support every conceivable sound card which is what this would entail. There was a real good reason to limit support to 1 or 2 radio interfaces! The radio interface hardware could then be controlled as a known quantity. This has been our philosophy since the project began. Supporing the IRLP board is not a simple prospect. The IRLP board is not the only peice of the puzzle. The IRLP board depends on a sound card, and this sound card can be anything. Although sound cards and IRLP interfaces are what folks have, and these folks don't want to invest in a whole new radio interface due to the added costs, the developers feel that this is too much of a burden on them and therefore have no inclination to open up support for every sound card out there. Steve WA6ZFT _______________________________________________ App_rpt-users mailing list App_rpt-users(a)qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users

1 0

Re: [App_rpt-users] usbradio similar driver with non usb
by Yokshs 08 Dec '09

08 Dec '09

> I made the changes to usbradio that you suggest about a year or so ago, and it worked ok. However I was just getting started with app-rpt, and > there were some other little issues I was having. I decided to mod the cm108 device and see how that compared. Unless you're using the > recommended hardware/software, it's really hard for anyone to help. I'm also interested in such a driver. I'd really like to continue using my IRLP board, but I can't seem to make app-rpt work with it directly. 73, Kyle K0KN

1 0

usbradio similar driver with non usb sound cards?
by Steve Gladden 07 Dec '09

07 Dec '09

Is it at all reasonable or worthwhile to even *think* I could write an alternate driver like usbradio but that uses some kind of 'generic' audio driver that outputs and captures audio from just about any 'common' PCI or ISA type sound card via it's normal linux driver.. and route radio PTT to something like a pin on a serial or parallel port?? I've been doing this for quite sometime with the Linux soundcard packet radio drivers where it almost doesn't matter what sound card you have installed it works.. Was just wondering if this is possible.. and if it may be a worthwhile project for me to eventually take on.. And what the good and bad may be in doing so. Is all the work that has been done on the cm108 driver so specific to the cm108 that it could not be easily applied to another sound device? Or is this rather simple and I should get to work on it? Thanks for entertaining my curiosity... I also thought that might be a really good learning project for me to do and learn how to do it... also why or why it may not be a good idea. Thanks! Steve -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.

2 1

Something hosed up again
by George Csahanin 06 Dec '09

06 Dec '09

I stopped and restared asterisk, and no more radio functions. Get this error: [Dec 6 15:01:27] ERROR[27267] codec_dahdi.c: Failed to open /dev/zap/transcode: No such file or directory radio and rpt functions not there... I tried to force that device to load by inserting the module, but no go. Related Modules that are loaded: Module Size Used by ztdummy 9256 0 wctdm 39628 0 wcfxo 15904 0 wctdm24xxp 115428 0 wcte11xp 26912 0 wct1xxp 17440 0 zaptel 191492 8 ztdummy,wctdm,wcfxo,wctdm24xxp,wcte11xp,wct1xxp crc_ccitt 6337 1 zaptel George J Csahanin W2DB Cedar Park, TX

1 0

*just for fun* ACID app_rpt usbradio on 64bit Linux / 64bit Centos
by Steve Gladden 06 Dec '09

06 Dec '09

Is app_rpt zaptel usbradio and all supported or expected to work/not work on a 64bit Linux installation? Is it expected to work / not work? I tried it just for fun and have not been able to get it to compile. I need to know if I should be completely avoiding 64bit Linux or if I should also be trying it out there as well. Thanks! Steve -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.

2 2

Odd-Splits in App_rpt
by Carl Swanson 05 Dec '09

05 Dec '09

Thanks for the heads up, Steve. Since app_rpt only seems to send offset direction to the G707, it must rely on the G707 to know what the offset is. I'm betting I can change the offset in the VHF band directly in the radio, and that will be a workable solution for one of the repeaters until the natural evolution of the application catches up. Thanks again. Carl/K6CRS

1 0