July 2010 - App_rpt-users - lists.keekles.org

Disabling Echo link announcements on non- Echo link nodes down stream
by REDBUTTON_CTRL 17 Jul '10

17 Jul '10

Hello, I have a question. If a non Echolink node is connected to another node that has chan_echolink setup and a Echolink connection comes into that node, is there a way to disable the Echolink connect and disconnect messages on the node that is connected down stream that doesn't have Echolink? If the connect messages are disabled on the Echolink node, does that disable the connect messages on the downstream node too or will it announce there since the telemetry is sent down stream? Or do the messages need to disabled on all connected nodes regardless? I guess the same rules would also apply for chan_IRLP too? Thanks, Jon VA3RQ

1 0

Re: [App_rpt-users] Node Disconnect
by David Powell-Williams 17 Jul '10

17 Jul '10

Jim Duuuuuude: Any chance you could elaborate a tad on the differences between a 'permalink' and a normal link? Such as what each do (or don't do) specifically? Any other 'doo-doo' on this topic would be of interest to your audience, I'm sure :) Cheers & 73, Dave VE7MQ 2140

2 1

OT: Anyone using an Android to dial into their system?
by Ramesh Dhami (VA3UV) 16 Jul '10

16 Jul '10

Hi Guys; Off-topic I know... is anyone using an Android to dial into their Asterisk / app_rpt system? - if so, which app' are you using? Conversely, is anyone using an iPhone - and if so, which app? Thx! Ramesh.

6 6

Node Disconnect
by Ron Phillips 15 Jul '10

15 Jul '10

I have a problem keeping two of my nodes connected at all times. It seems that if I lose the Internet connection for only a few seconds, the two nodes disconnect from each other. Is there a way to prevent this from happening? Ron, AA7RP

2 1

web xceiver
by Ken 15 Jul '10

15 Jul '10

Any idea how much horsepower is required to run this reliably? I imagine the Java parts of it need some power. Would it work on a 1.6 GHz single-core notebook or netbook? The processors in these have only about 1/3 the processing power of even a modest a dual core desktop (for example). What does it mean when the screen re-paints itself (most noticeable on the green banner on top)? What does it mean when the node connection status turns white momentarily? FWIW - hitting the refresh key disconnects and reconnects to the node Thanks Ken KE2N

1 0

web tranceiver
by Ken 13 Jul '10

13 Jul '10

This is pretty neat; it works fine from home?- I was hoping it would allow me to use my QRL laptop - but alas, while it displays the selected node information, pressing the "connect" button produces no obvious response. ? I believe the company proxy server blocks streaming audio and the internet gateway does not allow port pass through (other than the ones that allow you to browse the internet). ? It will play audio that is sent as a file (for example NWS weather service MP3's). ? Is there any hope for such as situation? ? Ken KE2N

2 1

Help local node control
by Paul M. Nannery 12 Jul '10

12 Jul '10

is thare a way to control a local node from a different local node with out going in to command mode? For example if I send pl disable on 440 from on my two meater repeater to make this happen without linking the two?

2 1

Re: [App_rpt-users] portal reverse patch question
by Ken 11 Jul '10

11 Jul '10

OK thanks It's a different DTMF on my system but now I get it. It worked for me &3 Ken From: Jim Duuuude [mailto:telesistant@hotmail.com] Sent: Sunday, July 11, 2010 4:16 PM To: ke2n(a)cs.com Subject: RE: [App_rpt-users] portal reverse patch question access the autopatch (*6) and dial 0701 like it says _____ From: ke2n(a)cs.com To: App_rpt-users(a)qrvc.com Date: Sun, 11 Jul 2010 15:50:45 -0400 Subject: [App_rpt-users] portal reverse patch question OK . I am a little thick I have managed to massage my system and the portal to where I can dial in, and bring up the repeater. It plays the "incoming call on node 0701" message. Now, how do I pick up the call from the repeater side? Thanks Ken KE2N W4BRM/R - 27021 =

1 0

portal reverse patch question
by Ken 11 Jul '10

11 Jul '10

OK . I am a little thick I have managed to massage my system and the portal to where I can dial in, and bring up the repeater. It plays the "incoming call on node 0701" message. Now, how do I pick up the call from the repeater side? Thanks Ken KE2N W4BRM/R - 27021

1 0

Re: [App_rpt-users] App_rpt-users Digest, Vol 17, Issue 4
by Neil Addis (WA5JXY) 11 Jul '10

11 Jul '10

DO NOT CLICK THE "LOLO.INOVEWEB" LINK BELOW. IT IS SPAM & INFECTED!!!! MODERATOR, Please delete! On Sun, Jul 11, 2010 at 10:00 AM, <app_rpt-users-request(a)qrvc.com> wrote: > Send App_rpt-users mailing list submissions to > app_rpt-users(a)qrvc.com > > To subscribe or unsubscribe via the World Wide Web, visit > http://qrvc.com/mailman/listinfo/app_rpt-users > or, via email, send a message with subject or body 'help' to > app_rpt-users-request(a)qrvc.com > > You can reach the person managing the list at > app_rpt-users-owner(a)qrvc.com > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of App_rpt-users digest..." > > > Today's Topics: > > 1. (no subject) (Keith Williamson) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Sat, 10 Jul 2010 09:35:34 -0700 > From: Keith Williamson <hkwilliamson(a)gmail.com> > Subject: [App_rpt-users] (no subject) > To: aa700.az(a)gmail.com, aa7oo.az(a)gmail.com, ac7fn(a)cox.net, > ag6rh(a)arrl.net, aj6rh(a)arrl.net, app_rpt-users(a)qrvc.com, > bbrown(a)byrg.net > Message-ID: > <AANLkTimy6W_GCR7dqCUnmbYvPY44jFx9wRzRMtbcYGrr(a)mail.gmail.com> > Content-Type: text/plain; charset=ISO-8859-1 > > http://lolo.inoveweb.com/default.php > > > ------------------------------ > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)qrvc.com > http://qrvc.com/mailman/listinfo/app_rpt-users > > > End of App_rpt-users Digest, Vol 17, Issue 4 > ******************************************** >

1 0