April 2012 - App_rpt-users - lists.keekles.org

Re: [App_rpt-users] Web Tans Help.
by Tim Sawyer 18 Apr '12

18 Apr '12

iaxRpt is a good alternative to the Web Transceiver. http://www.xelatec.com/xipar/iaxrpt -- Tim :wq On Apr 18, 2012, at 8:16 AM, Bradley Haney wrote: > Thanks for the info.. I re booted the router and either it was that > or just luck but it's back showing. But i don't think the router was > the problem as everything else was working. WEird. > > Bradley > > On Wed, Apr 18, 2012 at 10:03 AM, Tim Sawyer <tim.sawyer(a)me.com> wrote: >> It's probably something with the web transceiver. It's pretty much a piece of junk. It won't run at all on some computers. No one knows why. It's really unfortunate, it's so visible, it gives people a bad impression Allstar it does not deserve. >> >> One of the great things about Linux is that you seldom have to reinstall or reboot to fix things. Something is intermittent with the Web transceiver and the reinstall was probably not what fixed it. >> >> -- >> Tim >> :wq >> >> On Apr 17, 2012, at 8:00 PM, Bradley Haney wrote: >> >>> Hello all. I re installed allstarlink centos software and that got >>> the Web Trans working. Tonight I was on a net connected to my node >>> that is connected to our repeater during net time via the web trans >>> and it all of a sudden disconnected, but the echolink stations that >>> were connected were not booted off and the net finished i thought it >>> was my computer so i rebooted and tried the web trans and my node >>> wasn't listed, I then rebooted the ALLSTAR box and still nothing.. >>> Has anyone had this problem or do i need to re install the software? >>> >>> Thanks for any help >>> >>> Bradley >>> _______________________________________________ >>> App_rpt-users mailing list >>> App_rpt-users(a)ohnosec.org >>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >>

1 0

Web Tans Help.
by Bradley Haney 18 Apr '12

18 Apr '12

Hello all. I re installed allstarlink centos software and that got the Web Trans working. Tonight I was on a net connected to my node that is connected to our repeater during net time via the web trans and it all of a sudden disconnected, but the echolink stations that were connected were not booted off and the net finished i thought it was my computer so i rebooted and tried the web trans and my node wasn't listed, I then rebooted the ALLSTAR box and still nothing.. Has anyone had this problem or do i need to re install the software? Thanks for any help Bradley

2 1

Flashing DMK URI green light
by George Zolla 18 Apr '12

18 Apr '12

I just completed my AllStar system by connecting a DMK URI and radio cable to an Alinco DR-135 to my Mac Mini running AllStar. I set the conf file and before I tuned the radio I tried connecting my HT to the mobile to another node. It worked perfectly with an absolutely clear signal. I am very impressed! I have the S/W config Encode and Decode set as default - both = 100.0 and no encode or decode in my simplex radio. The only glitch I seem to have is that the green URI light flashes continually whether I am TX, RX or nothing. I have since tried to tune the radio with the AllStar instructions but everything seems to fail. However, the actual connection is awesome. I expect the URI should stay green unless TX but I am no sure. Could anyone give me some guidance? Thanks, I am very happy with the results! George K6GAZ

2 1

Set up URI rxnoise
by Eric Guth 16 Apr '12

16 Apr '12

Folks, I am Eric, 4Z5UG. I am setting up my first Allstar node using an URI to my Santec FM-240 2 meter transceiver. I am picking off discriminator audio from the radios receiver. I have 4 volts PtoP of noise with no carrier present. When I run the RXnoise test, it says that the "target is 27000", "tolerance 2750". My test measurement is 23000. I would think that 4 Volts p-p would be enough to get it right. Is there a way to change the target to put it in range of my noise output? 73, Eric, 4Z5UG

2 2

AllStar WebTransceiver-Server connection help ...
by Tony Youngblood 15 Apr '12

15 Apr '12

Problem -> I am unable to connect my allstar link portal phone (web transceiver) to node/server. It will connect to other nodes/servers just fine but when I point it to my own it won't connect. ;(;) AllStar 28384 Irlp 7998 / 7766 / 7926 Echo 563329 :(:)

1 0

propagate_dtmf
by Ramesh Dhami (VA3UV) 15 Apr '12

15 Apr '12

Hi All; Trying to setup a few systems up here in VE3 land, to allow dtmf tones to be passed from satellite nodes to a controller at the hub site. I have added the following lines in the rpt.conf file of one of my nodes (using chan_simpleusb): propagate_dtmf=yes inxlat=#56,#57,0123456789ABCD outxlat=#56,#57,0123456789ABCD Issue now is that I cannot get my local node to connect / disconnect - it appears as though it is not decoding dtmf at all. However, I can link / unlink using the CLI. Anyone 'been there, done that?' Thanks! Ramesh. www.freestar.us

1 0

WEB Trans not working ?
by Bradley Haney 15 Apr '12

15 Apr '12

Just got a new box and downloaded the software again got everything going including echo link and just went to try the web train's and it doesn't connect. I set this up by the web portal config and had the boxes marked. By chance does anyone know what to look for to see what the problem is? Thanks Bradley

1 0

Re: [App_rpt-users] Delete server
by Ken Robinson 15 Apr '12

15 Apr '12

Hi, I'm not sure how it happened, but I have had a station connect to me, disconnect and then reconnect without any problems I have both the portal and my server on static IP. Hopefully it is going to carry on working !!! Next problem I have to solve but not for a little while is I'm causing problems on the WAN by an extra-long squelch tail so that needs to be looked at Many thanks for your support, we may not have done much but the offer of assistance makes it worth while Regards Ken From: Tim Sawyer [mailto:tim.sawyer@me.com] Sent: 15 April 2012 17:04 To: Ken Robinson Cc: S. Scott; app_rpt List Subject: Re: [App_rpt-users] Delete server Ken, If you can open an IP address but not ports perhaps you're using the DMZ feature of your router than the port forward feature. Some routers call port forwarding different names. On your router it's called an "inbound rule". I've attached the manual for your router. See if you can make sense of port forwarding configuration on your router. If not we can see about setting it up for you. In that case we'll need some sort of screen share program like log-me-in or current version of skype. -- Tim :wq

1 0

Re: [App_rpt-users] Delete server
by Ken Robinson 15 Apr '12

15 Apr '12

Hi Tim, No I'm not using DMZ although I did try it to see if it made any difference, I have7 pc's in my network, one of them runs a mail server with port forwarding working perfectly well setting up port 4569 to the Centos pc appears to work ok too It is set up by setting up "services" which form part of firewall rules I have had the Centos pc set up with a static IP and had it running as dhcp. While I was out a friend managed to connect to me ( it was running as dhcp) but he said it wouldn't drop carrier so he disconnected I haven't been able to speak to him since so I'm not exactly sure what happened Ken From: Tim Sawyer [mailto:tim.sawyer@me.com] Sent: 15 April 2012 17:04 To: Ken Robinson Cc: S. Scott; app_rpt List Subject: Re: [App_rpt-users] Delete server Ken, If you can open an IP address but not ports perhaps you're using the DMZ feature of your router than the port forward feature. Some routers call port forwarding different names. On your router it's called an "inbound rule". I've attached the manual for your router. See if you can make sense of port forwarding configuration on your router. If not we can see about setting it up for you. In that case we'll need some sort of screen share program like log-me-in or current version of skype. -- Tim :wq

1 0

Delete server
by Ken Robinson 15 Apr '12

15 Apr '12

Hi Scott / Tim, I am afraid I have run out of ideas, I have even changed the 4569 port to 4568 just in case 4569 was still trying to latch itself onto the defunct G0LCE server. I also changed the port access in my router settings and in iax.conf files. I have my own dns server here and I can see my system and the portal talking to each other so I can only think that it is a port forwarding problem. One point, I have Echolink enabled and have the correct ports open too, does Echolink use the Allstar port 4569 too or does it access via the Echolink ports. If the answer is "it uses its own ports" then my theory of it being a port forwarding problem is shot down as it would need 3 ports to be setup wrong Could it be that the data on the Allstar Portal has been screwed up because of the way I originally set 2 servers on there. If so how can we un screw it Would re installing everything from here be worth trying? Regards Ken G0LCE

3 5