Hello my name is Loren I am trying to add custom Ident configuration with
the morse code ident that already exist does anyone know how i can link
these .wav files i created to work with all this I tried modifying the
rpt.conf area with idrecording= {File name} but couldn't for some reason
get it to play it not sure exactly what i need to do on this one also would
like to get rid of the telemetry after its connected to a node did it a few
times but for some reason the settings are not sticking like they should
any ideas? Thanks in advance 73's
Loren Tedford (KC9ZHV)
Email: lorentedford(a)gmail.com
http://www.lorentedford.com
Robert:
You made a good point.
Knowledge in at the library, you can get all you want.
Wisdom comes from life experience.
Good luck...
JK
From: Robert Newberry <N1XBM(a)amsat.org>
To: Johnny Keeker <cypresstower(a)yahoo.com>
Sent: Thursday, October 31, 2013 8:18 AM
Subject: Re: [App_rpt-users] Resistor divider
I should be able to use the DSP in the software to accomplish a high pass filter. I'm a little confused some people are adamant to use a resistor divider on a mastr ii and others say the DSP will handle it just fine. I guess I just need to try things and see for myself.
Apparare Scientior
Paratus Communicare
-N1XBM
On Oct 30, 2013 11:48 PM, "Johnny Keeker" <cypresstower(a)yahoo.com> wrote:
I use the capacitor it good design practice to isolates the circuits
>although it will not strip the pl or dpl. If I want to strip pl or dpl,
>use a Communication Specialists Board. You can try removes their
>audio cap and add jumpers. "Just kidding". Another consideration,
>take a look at, pin 16, connector P904, on the IF/Audio Squelch Board;
>RX PA. The audio is clean and de-emphasized.
>JK
>
>
>
>
>From: Robert Newberry <N1XBM(a)amsat.org>
>To: Johnny Keeker <cypresstower(a)yahoo.com>
>Sent: Wednesday, October 30, 2013 8:08 PM
>Subject: Re: [App_rpt-users] Resistor divider
>
>
>
>I just realized that the DSP should be able to strip PL off. At least I think it can.
>Apparare Scientior
>Paratus Communicare
>-N1XBM
>On Oct 30, 2013 6:44 PM, "Johnny Keeker" <cypresstower(a)yahoo.com> wrote:
>
>Robert;
>>You need to remove the sub audible tone when using vol hi,
>>but if your not concerned with hearing your ctcss tones,
>>use a 10uf cap off the vol hi through a series 10k to a 3.3k
>>to ground. Tap the audio where the 10k meets the 3.3k resistor.
>>Use a variable 5k pot in place of the 3.3k if you want to change
>>the levels or just change the 3.3k value....
>>JK
>>
>>
>>
>>From: Robert Newberry <N1XBM(a)amsat.org>
>>To: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org>
>>Sent: Wednesday, October 30, 2013 12:45 PM
>>Subject: [App_rpt-users] Resistor divider
>>
>>
>>
>>I need help, I am using a Mastr II and a URI. I want to use the vol/sql hi for my discriminator audio. I was going to use a resistor divider to pad down the audio.
>>Has anyone ever done this? Could you explain it in more detail to me. I've read you take the two resistors and put them in series. I would tap my URI in the middle where those two resistors meet. I assume one end goes to vol/sql hi, but where does the far end go?
>>Thanks for your help
>>Apparare Scientior
>>Paratus Communicare
>>-N1XBM
>>_______________________________________________
>>App_rpt-users mailing list
>>App_rpt-users(a)ohnosec.org
>>http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users
>>
>>
>>
>
>
I am a beginner to allstar. I have just setup echolink on my Allstar node hub. It is showing up on echolink.org. Two things I need help with...
How do you make a call out to a echolink node from the Allstar node? Trying the standard dtmf prefix plus the echolink node did not work.
I used the echolink app on my iphone to test. It says Welcome To All Star Node 28980, Echolink Node W9JSL-L, so it looks like it is connecting properly. The problem is that on the app its in receive mode and no option to transmit. Is there something in echolink.conf that needs to be configured to allow the echo iphone app to transmit?
