December 2014 - App_rpt-users - lists.keekles.org

Error Message When Attempting to Connect to my hub
by David Dean K0PWO 28 Dec '14

28 Dec '14

I copied an error message I am getting on the CLI of my Hub Node when I attempt to connect from my Repeater Node. I have been unable to connect to any other nodes for a while. I am not sure what changed but suddenly I could not connect to anyone any more. I copied and pasted the error message below in hopes that someone could point me in the right direction in finding the problem. I am guessing it has something to do with my router or modem. I currently use a ASUS RT-AC68U router which is provided IP from a Comcast supplied modem/router that is bridged so that its only a modem. I also have a cisco switch that I plug all my hardware into. Any help would be greatly appreciated. Connected to Asterisk currently running on K0PWO_Hub (pid = 2372) Verbosity is at least 3 -- Accepting UNAUTHENTICATED call from 192.168.20.1: > requested format = gsm, > requested prefs = (gsm|g726aal2|ulaw), > actual format = g726aal2, > host prefs = (g726aal2|gsm), > priority = mine -- Executing [41488@radio-secure:1] Rpt("IAX2/192.168.20.1:4569-1947", "4148 8") in new stack [Dec 27 16:33:51] WARNING[2930]: app_rpt.c:22704 rpt_exec: Node 40968 IP 73.169. 7.203 does not match link IP 192.168.20.1!! == Spawn extension (radio-secure, 41488, 1) exited non-zero on 'IAX2/192.168.2 0.1:4569-1947' -- Hungup 'IAX2/192.168.20.1:4569-1947' David Dean, K0PWO Arapahoe County Colorado (720) 350-2053 cell (720) 207-9030 fax

3 3

Re: [App_rpt-users] Remote Base question
by jumping_jackass＠yahoo.com 28 Dec '14

28 Dec '14

The Doug Hall unit can only control so far, You need to also review the Doug Hall documentation to see what it can not do. In your current case you should note that you need to set the step rate on your kenwood TM701 (dual-band radio) to 5 from its default of 25. I think that should get you a bit closer yet. I know this i have asked this before but, Why can the DMK-URI NOT send the serial data needed to the Doug Hall RBI-1 instead of the LPT port on the host PC? I have a RBI-1 that i have successfully used in the passed with the wb6ymh "THELINKBOX" radio over IP repeater controller and the DMK-URI did it all (serial and audio) so i know this works. JeffKD6GDB From: "app_rpt-users-request(a)ohnosec.org" <app_rpt-users-request(a)ohnosec.org> To: app_rpt-users(a)ohnosec.org Sent: Sunday, December 28, 2014 7:18 AM Subject: App_rpt-users Digest, Vol 70, Issue 52 Send App_rpt-users mailing list submissions to app_rpt-users(a)ohnosec.org To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request(a)ohnosec.org You can reach the person managing the list at app_rpt-users-owner(a)ohnosec.org When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..." Today's Topics: 1. Re: Remote Base question (Sam Nabkey) ---------------------------------------------------------------------- Message: 1 Date: Sun, 28 Dec 2014 10:18:54 -0500 From: Sam Nabkey <sam.nabkey(a)gmail.com> To: mike(a)midnighteng.com Cc: Allstar app_rpt-users Group <app_rpt-users(a)ohnosec.org> Subject: Re: [App_rpt-users] Remote Base question Message-ID: <CAO8AawpurWasp=Yvifdq_0tpSEmdRZ3Tsi7OC5X+T4Y4ubNMbg(a)mail.gmail.com> Content-Type: text/plain; charset="utf-8" I've used several fobs a URIx and a RIM. Same result. Sometimes I have to pull the fob from the port to get it to reset. Its either something I'm missing or ? On Dec 28, 2014 9:43 AM, <mike(a)midnighteng.com> wrote: > > Corey, > > I think I understand what you were saying about the querk in the DH RB. > > I can say that the doug hall has a few little issues of its own > (depending on firmware ver). > > 1st, even though you can power the rbi-1 through radio power, don't do > it. > Power with its own cord w 12vdc. > > But it is important to do the following when you setup from a fresh > power-up, > > watch the display to see which radio is being programed default at > power-up, > > enter a freq for each of the bands/radios you have installed until it > has powered off the unused bands/radios, starting with the one that it > reverted to last(blinked). > > When finished, you should have only the active working band/radio with > power-up. > (some older radios will not power down but x31,x41 should work ok) > > Then you can feel confident that it will run without error. > > It is possible to run into a error when switching from a radio memory to > a vfo mode especially after a reset. > > ...mike/kb8jnm > > > > -------- Original Message -------- > > Subject: Re: [App_rpt-users] Remote Base question > > From: Corey Dean <n3fe(a)repeater.net> > > Date: Sun, December 28, 2014 2:01 am > > To: Sam Nabkey <sam.nabkey(a)gmail.com> > > Cc: "mike(a)midnighteng.com" <mike(a)midnighteng.com>, Allstar app_rpt-users > > Group <app_rpt-users(a)ohnosec.org> > > > > > > When the node disconnects it does keep blinking. I played with it for > hours. Every once in a while the uhf side will mess is and instead of > taking say 444.050, it will take 440.050. Switch it back to vhf and then > to uhf fixes that though. Time will only tell how things will work! > > > > Corey > > > > > On Dec 28, 2014, at 1:23 AM, Sam Nabkey <sam.nabkey(a)gmail.com> wrote: > > > > > > Very cool Corey! > > > > > > I am glad you have it working... In your case, does the light stop > flashing when you disconnect from the RB? Mine doesn't and sometimes I > have to unplug and plug back in the URI for it to work again. > > > > > > Sam > > > > > >> On Sun, Dec 28, 2014 at 12:04 AM, Corey Dean <n3fe(a)repeater.net> > wrote: > > >> Well the remote base is up and running. > > >> > > >> One thing that got me and it shouldn't have was this was the first > time I used a FOB that had the blinking light on it. It had the blob over > the chip so I saved it for ACID use and the PP outputs and inputs. I kept > trying to troubleshoot why the light would stop blinking when I added in > remote=rbi. I shouldn't have worried about it as once I connected to it > from another node, the light started blinking and away I went. I also > didn't realize that the CLI wouldn't work unless another node or IAXRPT was > connected to the remote base. > > >> > > >> With that all squared away I still couldn't get things working. As > suggested by someone else I disconnected the reset line from pin 4 and > bam... It started working right away.. I spent many many hours on this > and all these little gotchas was what was holding me back. > > >> > > >> Thanks again for all the help from everyone. This was actually > pretty simple now that I know how things work when you are using a remote > base. It is a little different setup then configuring a regular node. > > >> > > >> Thanks again everyone! > > >> > > >> Corey N3FE > > >> > > >>> On Sat, Dec 27, 2014 at 9:02 AM, <mike(a)midnighteng.com> wrote: > > >>> > > >>> Sam and Corey, > > >>> > > >>> I did just want to point out that the one node connect is only valid > if > > >>> you use the > > >>> node=remote base option. > > >>> > > >>> 29261 = radio(a)127.0.0.1/29261,NONE,y ;y=remote base > > >>> > > >>> Without the "Y" many nodes can connect to the remote base node. > > >>> > > >>> What I did was put the control in a main node and use only use the > audio > > >>> paths for the remote base node then I do not have to connect to it in > > >>> control mode to control it. > > >>> This way I don't have to connect to it at all to control it. > > >>> May not be suitable for everyone's config though. > > >>> > > >>> And Sam may be right about the reset line, I have never connected it > > >>> myself. > > >>> Something to try. > > >>> > > >>> But I doubt it has any bearing on a FOB issue. > > >>> > > >>> I have no issues with DH-RBI > > >>> > > >>> ...mike/kb8jnm > > >>> > > >>> > -------- Original Message -------- > > >>> > Subject: Re: [App_rpt-users] Remote Base question > > >>> > From: Sam Nabkey <sam.nabkey(a)gmail.com> > > >>> > Date: Sat, December 27, 2014 8:46 am > > >>> > To: mike(a)midnighteng.com > > >>> > Cc: Allstar app_rpt-users Group <app_rpt-users(a)ohnosec.org> > > >>> > > > >>> > > > >>> > Corey.... > > >>> > > > >>> > I just went through this... > > >>> > > > >>> > here is what I have learned... > > >>> > > > >>> > The URI light will not blink until you connect to the Remote with > another > > >>> > node or iaxrpt. after that, it appears to stay blinking, however, > I believe > > >>> > it shoud go out again when you disconnect? Mine doesn't.. > > >>> > > > >>> > You need to use the *4xxx controlling the far node routine to > manipulate > > >>> > the remote from a connect node. OR you can use IAXRPT to test. > > >>> > > > >>> > I sometimes have to stop and restart asterisk to correct an issue > where the > > >>> > remote stops responding to anything. I think it has something to > do with > > >>> > the URI not disconnecting and the light stopping when you > disconnect. > > >>> > > > >>> > Only one node at a time can connect with the Remote Base. the > other > > >>> > attempts will fail. > > >>> > > > >>> > The Icom 706 needs Memories 50-99 entered and saved with the RPT > TONE set.. > > >>> > Starting at 67.0 at Memory 50 and going up each tone till you > reach the > > >>> > last tone and memory 99. I used 146.520 simplex in every memory > and just > > >>> > changed the tone incrementing 1 up till I hit 99 and the end of the > > >>> > available tones IF you don't do this, you will get "invalid > frequency" > > >>> > everytime. > > >>> > > > >>> > The RBI remote base works but I had to disconnect pin 4 it appears > in my > > >>> > case anyways, the logic level is backwards? As soon as I removed > the reset > > >>> > pin 4, it took right off. I am going to have to work on this > because the > > >>> > RBI operates with fewer mishaps when its connected. > > >>> > > > >>> > The Kenwood TMD-700a works the best for me so far. > > >>> > > > >>> > Corey, I run my nodes in a private invironment so I have removed > most of > > >>> > the band edge and authlevel safegards that maybe should be > included, but I > > >>> > wanted to get it to work before I added that back in. I am using > a USB > > >>> > Serial interface or a USB Icom interface in the case of the 706. > > >>> > > > >>> > here are my working examples. I hope it at least gets you > started. Your > > >>> > mileage may vary, CAUTION! Beverage may be HOT! (insert favorite > > >>> > disclaimer here..) > > >>> > > > >>> > ------ > > >>> > > > >>> > Example #1: For the IC-706: > > >>> > > > >>> > [582]; IC-706 Remote Base > > >>> > rxchannel=SimpleUSB/usb ; Rx audio/signalling channel > > >>> > duplex=1 > > >>> > context = radio > > >>> > accountcode=RADIO > > >>> > functions = functions > > >>> > memory = memory > > >>> > > > >>> > remote = ic706 > > >>> > ioport = /dev/ttyUSB0 > > >>> > civaddr = 88 > > >>> > authlevel=0 > > >>> > > > >>> > [functions] > > >>> > 0=remote,1 ; Retrieve Memory > > >>> > 1=remote,2 ; Set freq. > > >>> > 2=remote,3 ; Set tx PL tone > > >>> > 3=remote,4 ; Set rx PL tone > > >>> > 6=remote,6 ; Set Mode 1=FM 2=USB > 3=LSB 4=AM > > >>> > 40=remote,100 ; Rx PL off > > >>> > 41=remote,101 ; Rx PL on > > >>> > 42=remote,102 ; Tx PL off > > >>> > 43=remote,103 ; Tx PL on > > >>> > 44=remote,104 ; Low Power > > >>> > 45=remote,105 ; Medium Power > > >>> > 46=remote,106 ; High Power > > >>> > 711=remote,107 ; Bump -20 > > >>> > 714=remote,108 ; Bump -100 > > >>> > 717=remote,109 ; Bump -500 > > >>> > 713=remote,110 ; Bump +20 > > >>> > 716=remote,111 ; Bump +100 > > >>> > 719=remote,112 ; Bump +500 > > >>> > 721=remote,113 ; Scan - slow > > >>> > 724=remote,114 ; Scan - quick > > >>> > 727=remote,115 ; Scan - fast > > >>> > 723=remote,116 ; Scan + slow > > >>> > 726=remote,117 ; Scan + quick > > >>> > 729=remote,118 ; Scan + fast > > >>> > 79=remote,119 ; Tune > > >>> > 51=remote,5 ; Long status query > > >>> > 52=remote,140 ; Short status query > > >>> > 67=remote,210 ; Send a * > > >>> > 69=remote,211 ; Send a # > > >>> > > > >>> > [memory] > > >>> > init = 14.250,67.0,u ; 14.250MHz upper sideband > > >>> > 00 = 146.460,100.0,sht > > >>> > 01 = 146.940,100.0,-l > > >>> > 02 = 14.250,100.0,u ; 14.250MHz upper sideband > > >>> > > > >>> > [nodes] > > >>> > 582 = radio(a)127.0.0.1/582,NONE,y > > >>> > > > >>> > [nodes](+) > > >>> > #include nodes.include > > >>> > > > >>> > > ------------------------------------------------------------------------------------------------------------------------------------------------------------ > > >>> > > > >>> > EXAMPLE #2 For the RBI... > > >>> > > > >>> > [582]; Doug Hall RBI-1 > > >>> > rxchannel=SimpleUSB/usb ; Rx audio/signalling channel > > >>> > duplex=1 > > >>> > context = radio > > >>> > functions = functions > > >>> > memory = memory > > >>> > > > >>> > remote=rbi > > >>> > iobase=0x378 > > >>> > > > >>> > authlevel=0 > > >>> > > > >>> > [functions] > > >>> > 0=remote,1 ; Retrieve Memory > > >>> > 1=remote,2 ; Set freq. > > >>> > 2=remote,3 ; Set tx PL tone > > >>> > 3=remote,4 ; Set rx PL tone > > >>> > 5=remote,140 ; short status query > > >>> > 6=remote,5 ; Long Status Query > > >>> > > > >>> > 730=remote,100 ; Rx PL off > > >>> > 731=remote,101 ; Rx PL on > > >>> > 720=remote,102 ; Tx PL off > > >>> > 721=remote,103 ; Tx PL on > > >>> > 740=remote,104 ; Low Power > > >>> > 741=remote,105 ; Medium Power > > >>> > 742=remote,106 ; High Power > > >>> > > > >>> > [memory] > > >>> > init = 146.520,94.8,sht > > >>> > 26 = 147.260,94.8,+ltr > > >>> > 27 = 145.270,94.8,-ltr > > >>> > 11 = 145.110,94.8,-ltr > > >>> > 52 = 146.520,94.8,sh > > >>> > > > >>> > [nodes] > > >>> > 582 = radio(a)127.0.0.1/582,NONE,y > > >>> > > > >>> > [nodes](+) > > >>> > #include nodes.include > > >>> > > ______________________________________________________________________________ > > >>> > > > >>> > Example #3 For the Kenwood TMD-700a > > >>> > > > >>> > [582]; Kenwood TMD-700a > > >>> > rxchannel=SimpleUSB/usb ; Rx audio/signalling channel > > >>> > duplex=1 > > >>> > context = radio > > >>> > callerid = "K8SN 582" <6164389073> > > >>> > accountcode=RADIO > > >>> > functions = functions > > >>> > memory = memory > > >>> > > > >>> > remote = tmd700 > > >>> > ioport = /dev/ttyUSB0 > > >>> > > > >>> > authlevel=0 > > >>> > > > >>> > [functions] > > >>> > 0=remote,1 ; Retrieve Memory > > >>> > 1=remote,2 ; Set freq. > > >>> > 2=remote,3 ; Set tx PL tone > > >>> > 3=remote,4 ; Set rx PL tone > > >>> > 40=remote,100 ; Rx PL off > > >>> > 41=remote,101 ; Rx PL on > > >>> > 42=remote,102 ; Tx PL off > > >>> > 43=remote,103 ; Tx PL on > > >>> > 44=remote,104 ; Low Power > > >>> > 45=remote,105 ; Medium Power > > >>> > 46=remote,106 ; High Power > > >>> > 51=remote,5 ; Long status query > > >>> > 52=remote,140 ; Short status query > > >>> > 67=remote,210 ; Send a * > > >>> > 69=remote,211 ; Send a # > > >>> > > > >>> > [memory] > > >>> > init = 146.520,94.8,sht > > >>> > 26 = 147.260,94.8,+ltr > > >>> > 27 = 145.270,94.8,-ltr > > >>> > 11 = 145.110,94.8,-ltr > > >>> > 52 = 146.520,94.8,sht > > >>> > > > >>> > [nodes] > > >>> > 582 = radio(a)127.0.0.1/582,NONE,y > > >>> > > > >>> > [nodes](+) > > >>> > #include nodes.include > > >>> > > > >>> > > ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- > > >>> > > > >>> > On Sat, Dec 27, 2014 at 6:11 AM, <mike(a)midnighteng.com> wrote: > > >>> > > > >>> > > > > >>> > > > > >>> > > Corey, > > >>> > > > > >>> > > As we have talked on this before, > > >>> > > It really does not make any sense but here is a checklist. > > >>> > > > > >>> > > Look at usbradio.conf and > > >>> > > usbxxxxx.conf > > >>> > > Other than looking for type errors, make sure the fob is > addressed > > >>> > > properly. > > >>> > > > > >>> > > You might also add a > > >>> > > memory=memoryxxxxx section and provide a default freq load > string for > > >>> > > the node (rpt.conf). > > >>> > > > > >>> > > init=146.520,100.0,l > > >>> > > > > >>> > > It's a start anyway... > > >>> > > > > >>> > > ...mike/kb8jnm > > >>> > > > > >>> > > > -------- Original Message -------- > > >>> > > > Subject: [App_rpt-users] Remote Base question > > >>> > > > From: Corey Dean <n3fe(a)repeater.net> > > >>> > > > Date: Sat, December 27, 2014 12:09 am > > >>> > > > To: Allstar app_rpt-users Group <app_rpt-users(a)ohnosec.org> > > >>> > > > > > >>> > > > > > >>> > > > A few different times I have attempted to get a remote base > going. I am > > >>> > > > using a Doug Hall Box. I am sure I have it wired correctly. > On the > > >>> > > > Parallel port I have pin 2 as serial data, 3 as serial clock > and 4 as > > >>> > > > reset. > > >>> > > > > > >>> > > > If I define remote = rbi asterisk will start but the light on > the usb FOB > > >>> > > > stop blinking. Once I comment out the remote = line and > restart > > >>> > > asterisk, > > >>> > > > the sound fob will start to blink again and the doug hall will > reset. I > > >>> > > > decided to try defining any type of remote such as y or even > ic706 and > > >>> > > the > > >>> > > > same thing happens. > > >>> > > > > > >>> > > > When I do define remote=rbi it still will not program the > kenwood radio > > >>> > > > either. > > >>> > > > > > >>> > > > I did upgrade to the latest acid svn to test as well because > prior to > > >>> > > > upgrading if any remote at all was defined, asterisk wouldn't > even start. > > >>> > > > It would bomb right out. At least now it start. I know this > has to be > > >>> > > > something simple. Any one have any ideas as to where to start > looking? > > >>> > > > > > >>> > > > I did define a remote-base stanza for functions and the only > things I > > >>> > > added > > >>> > > > other than that was. > > >>> > > > > > >>> > > > remote = rbi > > >>> > > > iobase = 0x378 > > >>> > > > authlevel = 0 > > >>> > > > > > >>> > > > I am also using usbradio. > > >>> > > > > > >>> > > > Corey N3FE<hr>_______________________________________________ > > >>> > > > App_rpt-users mailing list > > >>> > > > App_rpt-users(a)ohnosec.org > > >>> > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > >>> > > > > > >>> > > > To unsubscribe from this list please visit > > >>> > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and > scroll down > > >>> > > to the bottom of the page. Enter your email address and press the > > >>> > > "Unsubscribe or edit options button" > > >>> > > > You do not need a password to unsubscribe, you can do it via > email > > >>> > > confirmation. If you have trouble unsubscribing, please send a > message to > > >>> > > the list detailing the problem. > > >>> > > _______________________________________________ > > >>> > > App_rpt-users mailing list > > >>> > > App_rpt-users(a)ohnosec.org > > >>> > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > >>> > > > > >>> > > To unsubscribe from this list please visit > > >>> > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and > scroll down > > >>> > > to the bottom of the page. Enter your email address and press the > > >>> > > "Unsubscribe or edit options button" > > >>> > > You do not need a password to unsubscribe, you can do it via > email > > >>> > > confirmation. If you have trouble unsubscribing, please send a > message to > > >>> > > the list detailing the problem. > > >>> > > > > >>> _______________________________________________ > > >>> App_rpt-users mailing list > > >>> App_rpt-users(a)ohnosec.org > > >>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > >>> > > >>> To unsubscribe from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down > to the bottom of the page. Enter your email address and press the > "Unsubscribe or edit options button" > > >>> You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message to > the list detailing the problem. > > >> > > >> > > >> _______________________________________________ > > >> App_rpt-users mailing list > > >> App_rpt-users(a)ohnosec.org > > >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > >> > > >> To unsubscribe from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down > to the bottom of the page. Enter your email address and press the > "Unsubscribe or edit options button" > > >> You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message to > the list detailing the problem. > > > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down > to the bottom of the page. Enter your email address and press the > "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message to > the list detailing the problem. >

1 0

Re: [App_rpt-users] Remote Base question
by mike＠midnighteng.com 28 Dec '14

28 Dec '14

Sam and Corey, I did just want to point out that the one node connect is only valid if you use the node=remote base option. 29261 = radio(a)127.0.0.1/29261,NONE,y ;y=remote base Without the "Y" many nodes can connect to the remote base node. What I did was put the control in a main node and use only use the audio paths for the remote base node then I do not have to connect to it in control mode to control it. This way I don't have to connect to it at all to control it. May not be suitable for everyone's config though. And Sam may be right about the reset line, I have never connected it myself. Something to try. But I doubt it has any bearing on a FOB issue. I have no issues with DH-RBI ...mike/kb8jnm > -------- Original Message -------- > Subject: Re: [App_rpt-users] Remote Base question > From: Sam Nabkey <sam.nabkey(a)gmail.com> > Date: Sat, December 27, 2014 8:46 am > To: mike(a)midnighteng.com > Cc: Allstar app_rpt-users Group <app_rpt-users(a)ohnosec.org> > > > Corey.... > > I just went through this... > > here is what I have learned... > > The URI light will not blink until you connect to the Remote with another > node or iaxrpt. after that, it appears to stay blinking, however, I believe > it shoud go out again when you disconnect? Mine doesn't.. > > You need to use the *4xxx controlling the far node routine to manipulate > the remote from a connect node. OR you can use IAXRPT to test. > > I sometimes have to stop and restart asterisk to correct an issue where the > remote stops responding to anything. I think it has something to do with > the URI not disconnecting and the light stopping when you disconnect. > > Only one node at a time can connect with the Remote Base. the other > attempts will fail. > > The Icom 706 needs Memories 50-99 entered and saved with the RPT TONE set.. > Starting at 67.0 at Memory 50 and going up each tone till you reach the > last tone and memory 99. I used 146.520 simplex in every memory and just > changed the tone incrementing 1 up till I hit 99 and the end of the > available tones IF you don't do this, you will get "invalid frequency" > everytime. > > The RBI remote base works but I had to disconnect pin 4 it appears in my > case anyways, the logic level is backwards? As soon as I removed the reset > pin 4, it took right off. I am going to have to work on this because the > RBI operates with fewer mishaps when its connected. > > The Kenwood TMD-700a works the best for me so far. > > Corey, I run my nodes in a private invironment so I have removed most of > the band edge and authlevel safegards that maybe should be included, but I > wanted to get it to work before I added that back in. I am using a USB > Serial interface or a USB Icom interface in the case of the 706. > > here are my working examples. I hope it at least gets you started. Your > mileage may vary, CAUTION! Beverage may be HOT! (insert favorite > disclaimer here..) > > ------ > > Example #1: For the IC-706: > > [582]; IC-706 Remote Base > rxchannel=SimpleUSB/usb ; Rx audio/signalling channel > duplex=1 > context = radio > accountcode=RADIO > functions = functions > memory = memory > > remote = ic706 > ioport = /dev/ttyUSB0 > civaddr = 88 > authlevel=0 > > [functions] > 0=remote,1 ; Retrieve Memory > 1=remote,2 ; Set freq. > 2=remote,3 ; Set tx PL tone > 3=remote,4 ; Set rx PL tone > 6=remote,6 ; Set Mode 1=FM 2=USB 3=LSB 4=AM > 40=remote,100 ; Rx PL off > 41=remote,101 ; Rx PL on > 42=remote,102 ; Tx PL off > 43=remote,103 ; Tx PL on > 44=remote,104 ; Low Power > 45=remote,105 ; Medium Power > 46=remote,106 ; High Power > 711=remote,107 ; Bump -20 > 714=remote,108 ; Bump -100 > 717=remote,109 ; Bump -500 > 713=remote,110 ; Bump +20 > 716=remote,111 ; Bump +100 > 719=remote,112 ; Bump +500 > 721=remote,113 ; Scan - slow > 724=remote,114 ; Scan - quick > 727=remote,115 ; Scan - fast > 723=remote,116 ; Scan + slow > 726=remote,117 ; Scan + quick > 729=remote,118 ; Scan + fast > 79=remote,119 ; Tune > 51=remote,5 ; Long status query > 52=remote,140 ; Short status query > 67=remote,210 ; Send a * > 69=remote,211 ; Send a # > > [memory] > init = 14.250,67.0,u ; 14.250MHz upper sideband > 00 = 146.460,100.0,sht > 01 = 146.940,100.0,-l > 02 = 14.250,100.0,u ; 14.250MHz upper sideband > > [nodes] > 582 = radio(a)127.0.0.1/582,NONE,y > > [nodes](+) > #include nodes.include > > ------------------------------------------------------------------------------------------------------------------------------------------------------------ > > EXAMPLE #2 For the RBI... > > [582]; Doug Hall RBI-1 > rxchannel=SimpleUSB/usb ; Rx audio/signalling channel > duplex=1 > context = radio > functions = functions > memory = memory > > remote=rbi > iobase=0x378 > > authlevel=0 > > [functions] > 0=remote,1 ; Retrieve Memory > 1=remote,2 ; Set freq. > 2=remote,3 ; Set tx PL tone > 3=remote,4 ; Set rx PL tone > 5=remote,140 ; short status query > 6=remote,5 ; Long Status Query > > 730=remote,100 ; Rx PL off > 731=remote,101 ; Rx PL on > 720=remote,102 ; Tx PL off > 721=remote,103 ; Tx PL on > 740=remote,104 ; Low Power > 741=remote,105 ; Medium Power > 742=remote,106 ; High Power > > [memory] > init = 146.520,94.8,sht > 26 = 147.260,94.8,+ltr > 27 = 145.270,94.8,-ltr > 11 = 145.110,94.8,-ltr > 52 = 146.520,94.8,sh > > [nodes] > 582 = radio(a)127.0.0.1/582,NONE,y > > [nodes](+) > #include nodes.include > ______________________________________________________________________________ > > Example #3 For the Kenwood TMD-700a > > [582]; Kenwood TMD-700a > rxchannel=SimpleUSB/usb ; Rx audio/signalling channel > duplex=1 > context = radio > callerid = "K8SN 582" <6164389073> > accountcode=RADIO > functions = functions > memory = memory > > remote = tmd700 > ioport = /dev/ttyUSB0 > > authlevel=0 > > [functions] > 0=remote,1 ; Retrieve Memory > 1=remote,2 ; Set freq. > 2=remote,3 ; Set tx PL tone > 3=remote,4 ; Set rx PL tone > 40=remote,100 ; Rx PL off > 41=remote,101 ; Rx PL on > 42=remote,102 ; Tx PL off > 43=remote,103 ; Tx PL on > 44=remote,104 ; Low Power > 45=remote,105 ; Medium Power > 46=remote,106 ; High Power > 51=remote,5 ; Long status query > 52=remote,140 ; Short status query > 67=remote,210 ; Send a * > 69=remote,211 ; Send a # > > [memory] > init = 146.520,94.8,sht > 26 = 147.260,94.8,+ltr > 27 = 145.270,94.8,-ltr > 11 = 145.110,94.8,-ltr > 52 = 146.520,94.8,sht > > [nodes] > 582 = radio(a)127.0.0.1/582,NONE,y > > [nodes](+) > #include nodes.include > > ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- > > On Sat, Dec 27, 2014 at 6:11 AM, <mike(a)midnighteng.com> wrote: > > > > > > > Corey, > > > > As we have talked on this before, > > It really does not make any sense but here is a checklist. > > > > Look at usbradio.conf and > > usbxxxxx.conf > > Other than looking for type errors, make sure the fob is addressed > > properly. > > > > You might also add a > > memory=memoryxxxxx section and provide a default freq load string for > > the node (rpt.conf). > > > > init=146.520,100.0,l > > > > It's a start anyway... > > > > ...mike/kb8jnm > > > > > -------- Original Message -------- > > > Subject: [App_rpt-users] Remote Base question > > > From: Corey Dean <n3fe(a)repeater.net> > > > Date: Sat, December 27, 2014 12:09 am > > > To: Allstar app_rpt-users Group <app_rpt-users(a)ohnosec.org> > > > > > > > > > A few different times I have attempted to get a remote base going. I am > > > using a Doug Hall Box. I am sure I have it wired correctly. On the > > > Parallel port I have pin 2 as serial data, 3 as serial clock and 4 as > > > reset. > > > > > > If I define remote = rbi asterisk will start but the light on the usb FOB > > > stop blinking. Once I comment out the remote = line and restart > > asterisk, > > > the sound fob will start to blink again and the doug hall will reset. I > > > decided to try defining any type of remote such as y or even ic706 and > > the > > > same thing happens. > > > > > > When I do define remote=rbi it still will not program the kenwood radio > > > either. > > > > > > I did upgrade to the latest acid svn to test as well because prior to > > > upgrading if any remote at all was defined, asterisk wouldn't even start. > > > It would bomb right out. At least now it start. I know this has to be > > > something simple. Any one have any ideas as to where to start looking? > > > > > > I did define a remote-base stanza for functions and the only things I > > added > > > other than that was. > > > > > > remote = rbi > > > iobase = 0x378 > > > authlevel = 0 > > > > > > I am also using usbradio. > > > > > > Corey N3FE<hr>_______________________________________________ > > > App_rpt-users mailing list > > > App_rpt-users(a)ohnosec.org > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > > > > To unsubscribe from this list please visit > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down > > to the bottom of the page. Enter your email address and press the > > "Unsubscribe or edit options button" > > > You do not need a password to unsubscribe, you can do it via email > > confirmation. If you have trouble unsubscribing, please send a message to > > the list detailing the problem. > > _______________________________________________ > > App_rpt-users mailing list > > App_rpt-users(a)ohnosec.org > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > > To unsubscribe from this list please visit > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down > > to the bottom of the page. Enter your email address and press the > > "Unsubscribe or edit options button" > > You do not need a password to unsubscribe, you can do it via email > > confirmation. If you have trouble unsubscribing, please send a message to > > the list detailing the problem. > >

3 3

Re: [App_rpt-users] Error Message When Attempting to Connect to my hub
by mike＠midnighteng.com 28 Dec '14

28 Dec '14

David, I think we need more info for that. but -Check your iax.conf for a registration type error, make sure your not using the same udp port on both servers Make sure the udp ports are not being used by other devices on your network. Check to see if you are actually registered on allstar.(may provide insight) ...mike/kb8jnm > -------- Original Message -------- > Subject: Re: [App_rpt-users] Error Message When Attempting to Connect to > my hub > From: David Dean <david(a)k0pwo.com> > Date: Sat, December 27, 2014 8:48 pm > To: Jim Duuuude <telesistant(a)hotmail.com> > Cc: app_rpt mailing list <app_rpt-users(a)ohnosec.org> > > > Ok I understand that and will make those changes but I am still unable to connect to other nodes outside of my lan. Any thoughts on that. > > Sent from my iPhone > > > On Dec 27, 2014, at 6:41 PM, Jim Duuuude <telesistant(a)hotmail.com> wrote: > > > > Dude, > > > > put: > > > > 40968 = radio(a)192.168.20.1/40968,NONE > > > > in the [nodes] section of rpt.conf. > > > > Obviously, you have 2 app_rpt servers on the same LAN (behind the same NAT). > > This, and a line in the OTHER server's rpt.conf (that will allow connections the other way), > > is necessary in this type of configuration. > > > > Jim > > > > From: david(a)k0pwo.com > > To: app_rpt-users(a)ohnosec.org > > Date: Sat, 27 Dec 2014 18:09:13 -0700 > > Subject: [App_rpt-users] Error Message When Attempting to Connect to my hub > > > > I copied an error message I am getting on the CLI of my Hub Node when I attempt to connect from my Repeater Node. I have been unable to connect to any other nodes for a while. I am not sure what changed but suddenly I could not connect to anyone any more. > > > > > > > > I copied and pasted the error message below in hopes that someone could point me in the right direction in finding the problem. I am guessing it has something to do with my router or modem. > > > > > > > > I currently use a ASUS RT-AC68U router which is provided IP from a Comcast supplied modem/router that is bridged so that its only a modem. I also have a cisco switch that I plug all my hardware into. > > > > > > > > Any help would be greatly appreciated. > > > > > > > > Connected to Asterisk currently running on K0PWO_Hub (pid = 2372) > > > > Verbosity is at least 3 > > > > -- Accepting UNAUTHENTICATED call from 192.168.20.1: > > > > > requested format = gsm, > > > > > requested prefs = (gsm|g726aal2|ulaw), > > > > > actual format = g726aal2, > > > > > host prefs = (g726aal2|gsm), > > > > > priority = mine > > > > -- Executing [41488@radio-secure:1] Rpt("IAX2/192.168.20.1:4569-1947", "4148 8") in new stack > > > > [Dec 27 16:33:51] WARNING[2930]: app_rpt.c:22704 rpt_exec: Node 40968 IP 73.169. 7.203 does not match link IP 192.168.20.1!! > > > > == Spawn extension (radio-secure, 41488, 1) exited non-zero on 'IAX2/192.168.2 0.1:4569-1947' > > > > -- Hungup 'IAX2/192.168.20.1:4569-1947' > > > > > > > > > > > > > > > > David Dean, K0PWO > > > > > > > > Arapahoe County Colorado > > > > (720) 350-2053 cell > > > > (720) 207-9030 fax > > > > > > > > > > > > > > > > > > _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.<hr>_______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

2 1

Re: [App_rpt-users] Error Message When Attempting to Connect to my hub
by mike＠midnighteng.com 28 Dec '14

28 Dec '14

David, Forgive me if i am wrong, It looks like a incoming connect not a out going connect. ??? True? What device in on the other end of this connect attempt ? If I am right on that and it is a incoming connect attempt, then check your extentions.conf for that node/hub as it must be a type error in the stanza for that node making it auto-fall-through/hang-up. Let me know for sure so we can help if it's still a problem. ...mike/kb8jnm > -------- Original Message -------- > Subject: [App_rpt-users] Error Message When Attempting to Connect to my > hub > From: "David Dean K0PWO" <david(a)k0pwo.com> > Date: Sat, December 27, 2014 8:09 pm > To: "'Allstar app_rpt-users Group'" <app_rpt-users(a)ohnosec.org> > > > I copied an error message I am getting on the CLI of my Hub Node when I > attempt to connect from my Repeater Node. I have been unable to connect to > any other nodes for a while. I am not sure what changed but suddenly I could > not connect to anyone any more. > > > > I copied and pasted the error message below in hopes that someone could > point me in the right direction in finding the problem. I am guessing it has > something to do with my router or modem. > > > > I currently use a ASUS RT-AC68U router which is provided IP from a Comcast > supplied modem/router that is bridged so that its only a modem. I also have > a cisco switch that I plug all my hardware into. > > > > Any help would be greatly appreciated. > > > > Connected to Asterisk currently running on K0PWO_Hub (pid = 2372) > > Verbosity is at least 3 > > -- Accepting UNAUTHENTICATED call from 192.168.20.1: > > > requested format = gsm, > > > requested prefs = (gsm|g726aal2|ulaw), > > > actual format = g726aal2, > > > host prefs = (g726aal2|gsm), > > > priority = mine > > -- Executing [41488@radio-secure:1] Rpt("IAX2/192.168.20.1:4569-1947", > "4148 8") in new stack > > [Dec 27 16:33:51] WARNING[2930]: app_rpt.c:22704 rpt_exec: Node 40968 IP > 73.169. 7.203 does not match link IP 192.168.20.1!! > > == Spawn extension (radio-secure, 41488, 1) exited non-zero on > 'IAX2/192.168.2 0.1:4569-1947' > > -- Hungup 'IAX2/192.168.20.1:4569-1947' > > > > > > > > David Dean, K0PWO > > > > Arapahoe County Colorado > > (720) 350-2053 cell > > (720) 207-9030 fax<hr>_______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

1 0

Re: [App_rpt-users] reverse autopatch for IP phone network
by Mike Lussier 27 Dec '14

27 Dec '14

Robert, You nailed it. That is what I did and it appears to have worked for me. Your email was just a little late, Still appreciated as was everyone else’s responses. I created two IAX trunks for now. There is one for each of the two BBB that I have available right now. I have tested one unit so far and I may go back and visit this more tomorrow. I'm thinking one trunk to the hub and then connect the other nodes from that point. Instead of connecting each mode to the two PBX's here at the house. Mike -- *"We must reject the idea that every time a law is broken, society is guilty rather than the law breaker.It is time to restore the American precept that each individual is accountable for his actions." ~ Ronald Regan*

1 0

Re: [App_rpt-users] reverse autopatch for IP phone network
by mike＠midnighteng.com 27 Dec '14

27 Dec '14

Steve, I can't speak for it being there or not as I have not got one yet, but I know there were compromises to get it to fit and function well into the 1gb memory of a BBB and have some headroom for radio expansion. Perhaps someone else knows or can you can look in the modules installed at the compiler. Nothing stopping anyone from installing the modules required and recompiling ! I'm sure it will be more than one as for dependencies. ...mike/kb8jnm > -------- Original Message -------- > Subject: Re: [App_rpt-users] reverse autopatch for IP phone network > From: Steven Donegan <steve(a)donegan.org> > Date: Sat, December 27, 2014 3:55 pm > To: "Robert A. Poff" <wb3awj(a)comcast.net>, "app_rpt-users(a)ohnosec.org" > <app_rpt-users(a)ohnosec.org> > > > If this is true (not doubting you) then a BBB which I have would not fit for my needs. My current node is on a small form factor PC and does PBX duty for my home QTH as well as the interface to Allstar and the URIx. It is a whimpy 1.6 GHz PC and seems to handle the duties fine so I would expect the BBB could as well if enabled to do so. > ____________ > Steven Donegan > KK6IVC FCC Technician Class License > SSCC/NORC Life Member, Car #86 > www.sscc.us > > From: Robert A. Poff <wb3awj(a)comcast.net> > To: app_rpt-users(a)ohnosec.org > Sent: Saturday, December 27, 2014 12:29 PM > Subject: Re: [App_rpt-users] reverse autopatch for IP phone network > > If memory serves correctly..... on the BBB version they removed SIP functionally. > > Try using IAX. > > > -- > Sent from my Android device with K-9 Mail. Please excuse my brevity. > > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.<hr>_______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

2 1

Re: [App_rpt-users] reverse autopatch for IP phone network
by mike＠midnighteng.com 27 Dec '14

27 Dec '14

Mike, Not sure what the exact problem is, you did not state it. I'm guessing your problem is in trunking/peering the asterisk/home-pbx to asterisk/app_rpt You are missing a context= statement. Probably want to use radio-control for it on app_rpt side. If not, asterisk knows not what stanza to associate the call with and you will not get the correct channel. There is more than one way to do the trunking or peering systems. I'm not sure I am following what you are doing from what is shown. ...mike/kb8jnm > -------- Original Message -------- > Subject: [App_rpt-users] reverse autopatch for IP phone network > From: Mike Lussier <mike.lussier(a)gmail.com> > Date: Sat, December 27, 2014 10:39 am > To: ALL STAR <app_rpt-users(a)ohnosec.org> > > > Good morning all. > > I did my due diligence by researching the archives for my answer first. > > I saw that K1LNX had posted in 2010 [App_rpt-users] Example of how to setup > a sip phone for reverse autopatch. > I have been playing with this the past 24 hours. My home pbx is asterisk > PBX and my nodes are all Beagle Bone Black running the new load. It seems > to be a problem with sip. > I have configured sip trunk (radio1) on my PBX peer details for: > Host=10.133.54.132 > Username=ae4ml > Secret=passwd > type=friend > > registration string ae4ml:passwd@10.133.54.132/radio1 > > Outbound route radio1 > dialplan 1XXX > Trunk radio1 > > > > -- > > *"We must reject the idea that every time a law is broken, society is > guilty rather than the law breaker.It is time to restore the American > precept that each individual is accountable for his actions." ~ Ronald > Regan*<hr>_______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

4 3

reverse autopatch for IP phone network
by Mike Lussier 27 Dec '14

27 Dec '14

Good morning all. I did my due diligence by researching the archives for my answer first. I saw that K1LNX had posted in 2010 [App_rpt-users] Example of how to setup a sip phone for reverse autopatch. I have been playing with this the past 24 hours. My home pbx is asterisk PBX and my nodes are all Beagle Bone Black running the new load. It seems to be a problem with sip. I have configured sip trunk (radio1) on my PBX peer details for: Host=10.133.54.132 Username=ae4ml Secret=passwd type=friend registration string ae4ml:passwd@10.133.54.132/radio1 Outbound route radio1 dialplan 1XXX Trunk radio1 -- *"We must reject the idea that every time a law is broken, society is guilty rather than the law breaker.It is time to restore the American precept that each individual is accountable for his actions." ~ Ronald Regan*

1 0

Re: [App_rpt-users] Remote Base questionw
by mike＠midnighteng.com 27 Dec '14

27 Dec '14

Sam, That was in the last message... in rpt.conf > > 29261 = radio(a)127.0.0.1/29261,NONE,y ;y=remote base > > > > Without the "Y" many nodes can connect to the remote base node. Don't declare it as a remote base with the "y" It is something to think about before deciding it is a good route to take considering all your possible config's. It all depends on your intentions and set-up. It not good for everyone. ...mike/kb8jnm > -------- Original Message -------- > Subject: Re: [App_rpt-users] Remote Base questionw > From: Sam Nabkey <sam.nabkey(a)gmail.com> > Date: Sat, December 27, 2014 9:16 am > To: mike(a)midnighteng.com > Cc: Allstar app_rpt-users Group <app_rpt-users(a)ohnosec.org> > > > Pretty sure the FOB issue is you need to connect to it first to get the > light to blink. > > Mike.. Tell me about the way you configure yours to allow multiple connects? > > Sam > > > On Dec 27, 2014 9:11 AM, <mike(a)midnighteng.com> wrote: > > > > > Sam and Corey, > > > > I did just want to point out that the one node connect is only valid if > > you use the > > node=remote base option. > > > > 29261 = radio(a)127.0.0.1/29261,NONE,y ;y=remote base > > > > Without the "Y" many nodes can connect to the remote base node. > > > > What I did was put the control in a main node and use only use the audio > > paths for the remote base node then I do not have to connect to it in > > control mode to control it. > > This way I don't have to connect to it at all to control it. > > May not be suitable for everyone's config though. > > > > And Sam may be right about the reset line, I have never connected it > > myself. > > Something to try. > > > > But I doubt it has any bearing on a FOB issue. > > > > I have no issues with DH-RBI > > > > ...mike/kb8jnm > > > > > -------- Original Message -------- > > > Subject: Re: [App_rpt-users] Remote Base question > > > From: Sam Nabkey <sam.nabkey(a)gmail.com> > > > Date: Sat, December 27, 2014 8:46 am > > > To: mike(a)midnighteng.com > > > Cc: Allstar app_rpt-users Group <app_rpt-users(a)ohnosec.org> > > > > > > > > > Corey.... > > > > > > I just went through this... > > > > > > here is what I have learned... > > > > > > The URI light will not blink until you connect to the Remote with another > > > node or iaxrpt. after that, it appears to stay blinking, however, I > > believe > > > it shoud go out again when you disconnect? Mine doesn't.. > > > > > > You need to use the *4xxx controlling the far node routine to manipulate > > > the remote from a connect node. OR you can use IAXRPT to test. > > > > > > I sometimes have to stop and restart asterisk to correct an issue where > > the > > > remote stops responding to anything. I think it has something to do with > > > the URI not disconnecting and the light stopping when you disconnect. > > > > > > Only one node at a time can connect with the Remote Base. the other > > > attempts will fail. > > > > > > The Icom 706 needs Memories 50-99 entered and saved with the RPT TONE > > set.. > > > Starting at 67.0 at Memory 50 and going up each tone till you reach the > > > last tone and memory 99. I used 146.520 simplex in every memory and just > > > changed the tone incrementing 1 up till I hit 99 and the end of the > > > available tones IF you don't do this, you will get "invalid frequency" > > > everytime. > > > > > > The RBI remote base works but I had to disconnect pin 4 it appears in my > > > case anyways, the logic level is backwards? As soon as I removed the > > reset > > > pin 4, it took right off. I am going to have to work on this because the > > > RBI operates with fewer mishaps when its connected. > > > > > > The Kenwood TMD-700a works the best for me so far. > > > > > > Corey, I run my nodes in a private invironment so I have removed most of > > > the band edge and authlevel safegards that maybe should be included, but > > I > > > wanted to get it to work before I added that back in. I am using a USB > > > Serial interface or a USB Icom interface in the case of the 706. > > > > > > here are my working examples. I hope it at least gets you started. Your > > > mileage may vary, CAUTION! Beverage may be HOT! (insert favorite > > > disclaimer here..) > > > > > > ------ > > > > > > Example #1: For the IC-706: > > > > > > [582]; IC-706 Remote Base > > > rxchannel=SimpleUSB/usb ; Rx audio/signalling channel > > > duplex=1 > > > context = radio > > > accountcode=RADIO > > > functions = functions > > > memory = memory > > > > > > remote = ic706 > > > ioport = /dev/ttyUSB0 > > > civaddr = 88 > > > authlevel=0 > > > > > > [functions] > > > 0=remote,1 ; Retrieve Memory > > > 1=remote,2 ; Set freq. > > > 2=remote,3 ; Set tx PL tone > > > 3=remote,4 ; Set rx PL tone > > > 6=remote,6 ; Set Mode 1=FM 2=USB 3=LSB 4=AM > > > 40=remote,100 ; Rx PL off > > > 41=remote,101 ; Rx PL on > > > 42=remote,102 ; Tx PL off > > > 43=remote,103 ; Tx PL on > > > 44=remote,104 ; Low Power > > > 45=remote,105 ; Medium Power > > > 46=remote,106 ; High Power > > > 711=remote,107 ; Bump -20 > > > 714=remote,108 ; Bump -100 > > > 717=remote,109 ; Bump -500 > > > 713=remote,110 ; Bump +20 > > > 716=remote,111 ; Bump +100 > > > 719=remote,112 ; Bump +500 > > > 721=remote,113 ; Scan - slow > > > 724=remote,114 ; Scan - quick > > > 727=remote,115 ; Scan - fast > > > 723=remote,116 ; Scan + slow > > > 726=remote,117 ; Scan + quick > > > 729=remote,118 ; Scan + fast > > > 79=remote,119 ; Tune > > > 51=remote,5 ; Long status query > > > 52=remote,140 ; Short status query > > > 67=remote,210 ; Send a * > > > 69=remote,211 ; Send a # > > > > > > [memory] > > > init = 14.250,67.0,u ; 14.250MHz upper sideband > > > 00 = 146.460,100.0,sht > > > 01 = 146.940,100.0,-l > > > 02 = 14.250,100.0,u ; 14.250MHz upper sideband > > > > > > [nodes] > > > 582 = radio(a)127.0.0.1/582,NONE,y > > > > > > [nodes](+) > > > #include nodes.include > > > > > > > > ------------------------------------------------------------------------------------------------------------------------------------------------------------ > > > > > > EXAMPLE #2 For the RBI... > > > > > > [582]; Doug Hall RBI-1 > > > rxchannel=SimpleUSB/usb ; Rx audio/signalling channel > > > duplex=1 > > > context = radio > > > functions = functions > > > memory = memory > > > > > > remote=rbi > > > iobase=0x378 > > > > > > authlevel=0 > > > > > > [functions] > > > 0=remote,1 ; Retrieve Memory > > > 1=remote,2 ; Set freq. > > > 2=remote,3 ; Set tx PL tone > > > 3=remote,4 ; Set rx PL tone > > > 5=remote,140 ; short status query > > > 6=remote,5 ; Long Status Query > > > > > > 730=remote,100 ; Rx PL off > > > 731=remote,101 ; Rx PL on > > > 720=remote,102 ; Tx PL off > > > 721=remote,103 ; Tx PL on > > > 740=remote,104 ; Low Power > > > 741=remote,105 ; Medium Power > > > 742=remote,106 ; High Power > > > > > > [memory] > > > init = 146.520,94.8,sht > > > 26 = 147.260,94.8,+ltr > > > 27 = 145.270,94.8,-ltr > > > 11 = 145.110,94.8,-ltr > > > 52 = 146.520,94.8,sh > > > > > > [nodes] > > > 582 = radio(a)127.0.0.1/582,NONE,y > > > > > > [nodes](+) > > > #include nodes.include > > > > > ______________________________________________________________________________ > > > > > > Example #3 For the Kenwood TMD-700a > > > > > > [582]; Kenwood TMD-700a > > > rxchannel=SimpleUSB/usb ; Rx audio/signalling channel > > > duplex=1 > > > context = radio > > > callerid = "K8SN 582" <6164389073> > > > accountcode=RADIO > > > functions = functions > > > memory = memory > > > > > > remote = tmd700 > > > ioport = /dev/ttyUSB0 > > > > > > authlevel=0 > > > > > > [functions] > > > 0=remote,1 ; Retrieve Memory > > > 1=remote,2 ; Set freq. > > > 2=remote,3 ; Set tx PL tone > > > 3=remote,4 ; Set rx PL tone > > > 40=remote,100 ; Rx PL off > > > 41=remote,101 ; Rx PL on > > > 42=remote,102 ; Tx PL off > > > 43=remote,103 ; Tx PL on > > > 44=remote,104 ; Low Power > > > 45=remote,105 ; Medium Power > > > 46=remote,106 ; High Power > > > 51=remote,5 ; Long status query > > > 52=remote,140 ; Short status query > > > 67=remote,210 ; Send a * > > > 69=remote,211 ; Send a # > > > > > > [memory] > > > init = 146.520,94.8,sht > > > 26 = 147.260,94.8,+ltr > > > 27 = 145.270,94.8,-ltr > > > 11 = 145.110,94.8,-ltr > > > 52 = 146.520,94.8,sht > > > > > > [nodes] > > > 582 = radio(a)127.0.0.1/582,NONE,y > > > > > > [nodes](+) > > > #include nodes.include > > > > > > > > ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- > > > > > > On Sat, Dec 27, 2014 at 6:11 AM, <mike(a)midnighteng.com> wrote: > > > > > > > > > > > > > > > Corey, > > > > > > > > As we have talked on this before, > > > > It really does not make any sense but here is a checklist. > > > > > > > > Look at usbradio.conf and > > > > usbxxxxx.conf > > > > Other than looking for type errors, make sure the fob is addressed > > > > properly. > > > > > > > > You might also add a > > > > memory=memoryxxxxx section and provide a default freq load string for > > > > the node (rpt.conf). > > > > > > > > init=146.520,100.0,l > > > > > > > > It's a start anyway... > > > > > > > > ...mike/kb8jnm > > > > > > > > > -------- Original Message -------- > > > > > Subject: [App_rpt-users] Remote Base question > > > > > From: Corey Dean <n3fe(a)repeater.net> > > > > > Date: Sat, December 27, 2014 12:09 am > > > > > To: Allstar app_rpt-users Group <app_rpt-users(a)ohnosec.org> > > > > > > > > > > > > > > > A few different times I have attempted to get a remote base going. > > I am > > > > > using a Doug Hall Box. I am sure I have it wired correctly. On the > > > > > Parallel port I have pin 2 as serial data, 3 as serial clock and 4 as > > > > > reset. > > > > > > > > > > If I define remote = rbi asterisk will start but the light on the > > usb FOB > > > > > stop blinking. Once I comment out the remote = line and restart > > > > asterisk, > > > > > the sound fob will start to blink again and the doug hall will > > reset. I > > > > > decided to try defining any type of remote such as y or even ic706 > > and > > > > the > > > > > same thing happens. > > > > > > > > > > When I do define remote=rbi it still will not program the kenwood > > radio > > > > > either. > > > > > > > > > > I did upgrade to the latest acid svn to test as well because prior to > > > > > upgrading if any remote at all was defined, asterisk wouldn't even > > start. > > > > > It would bomb right out. At least now it start. I know this has to > > be > > > > > something simple. Any one have any ideas as to where to start > > looking? > > > > > > > > > > I did define a remote-base stanza for functions and the only things I > > > > added > > > > > other than that was. > > > > > > > > > > remote = rbi > > > > > iobase = 0x378 > > > > > authlevel = 0 > > > > > > > > > > I am also using usbradio. > > > > > > > > > > Corey N3FE<hr>_______________________________________________ > > > > > App_rpt-users mailing list > > > > > App_rpt-users(a)ohnosec.org > > > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > > > > > > > > To unsubscribe from this list please visit > > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll > > down > > > > to the bottom of the page. Enter your email address and press the > > > > "Unsubscribe or edit options button" > > > > > You do not need a password to unsubscribe, you can do it via email > > > > confirmation. If you have trouble unsubscribing, please send a message > > to > > > > the list detailing the problem. > > > > _______________________________________________ > > > > App_rpt-users mailing list > > > > App_rpt-users(a)ohnosec.org > > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > > > > > > To unsubscribe from this list please visit > > > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll > > down > > > > to the bottom of the page. Enter your email address and press the > > > > "Unsubscribe or edit options button" > > > > You do not need a password to unsubscribe, you can do it via email > > > > confirmation. If you have trouble unsubscribing, please send a message > > to > > > > the list detailing the problem. > > > > > > _______________________________________________ > > App_rpt-users mailing list > > App_rpt-users(a)ohnosec.org > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > > To unsubscribe from this list please visit > > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down > > to the bottom of the page. Enter your email address and press the > > "Unsubscribe or edit options button" > > You do not need a password to unsubscribe, you can do it via email > > confirmation. If you have trouble unsubscribing, please send a message to > > the list detailing the problem. > >

1 0