- App_rpt-users - lists.keekles.org

Android IAXRPT new phone
by Robert Newberry 21 Jul '16

21 Jul '16

I grabbed the Android IAXRPT from dropbox. The link I had it says it was 2 months old. I installed it on my new Samsung edge 7. I can not figure out how to exit the program. Is there a way to do this?

5 10

Levels
by Robert Newberry 20 Jul '16

20 Jul '16

Does anyone on this list have problems with people saying the level sounds a bit soft on their repeater? I set mine using the "preferred method" with a calibrated servicr monitor, outlined on the allstar page. Basically 3khz in 3khz out. All of the repeaters I setup I can change channels on my radio and the levels are equal and sound right to me. I run my radio at half volume. The people complaining about my levels are basing this on what they hear by ear in their car and compare me to to repeaters that were set up by people using their ear and not test gear. I'm basically holding the line and reluctant to budge, but maybe I'm missing something, such as is using that method for setup a little stingey on the level? I'm confident I'm setup right, but I'm scratching my head on the comments. N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812, 42086, 42658, 42657 www.radioguysrepeaternetwork.com

3 2

Re: [App_rpt-users] Outbound call problem! Unable to handle indication 13
by Pawlowski, Adam 18 Jul '16

18 Jul '16

This is what I have for my node: add action=dst-nat chain=dstnat comment="Allstar Link IAX2" dst-port=4569 in-interface=ether1-gateway protocol=udp to-addresses=192.168.1.120 to-ports=4569 add action=dst-nat chain=dstnat comment="Allstarlink chan_echolink" dst-port=5198-5199 in-interface=ether1-gateway protocol=udp to-addresses=192.168.1.120 to-ports=5198-5199 add action=dst-nat chain=dstnat comment="Allstarlink SIP" dst-port=5060 in-interface=ether1-gateway protocol=udp to-addresses=192.168.1.120 to-ports=5060 add action=dst-nat chain=dstnat comment="Allstarlink RTP" dst-port=10000-65535 in-interface=ether1-gateway protocol=udp to-addresses=192.168.1.120 to-ports=10000-65535 I am not running a src nat for the IAX port outbound. I have the rule in the chain but disabled, so I must have determined I didn't need it. It either does PAT correctly in the background, or isn't natting that port: 220controller*CLI> iax2 show registry Host dnsmgr Username Perceived Refresh State 67.215.233.178:4569 Y 27709 67.242.153.201:4569 60 Registered I installed the MicroTIK router to replace an Adtran device which was utter trash and refused to do a static PAT, and it's been working swell since, to the best of my knowledge. If there's some reason I should be doing a source NAT for that port, I guess, let me know? I suppose it would only make a difference if I'm operating multiple nodes and didn't want to connect them together internally. Regards, Adam KC2YQF

3 4

Re: [App_rpt-users] App_rpt-users Digest, Vol 89, Issue 53
by R Dahl 18 Jul '16

18 Jul '16

> > > 1. Re: Outbound call problem! Unable to handle indication 13 > (Skyler F) > 2. Re: Outbound call problem! Unable to handle indication 13 > (Skyler F) > 3. Record Connections? (Bob) > 4. Re: Outbound call problem! Unable to handle indication 13 > (Eric Meth) > > Skyler, although not quite the same as the problem I was having, it sounds > similar and might require a hairpin NAT in the Mikrotik. There should be > several references to that in the archives. Ross

1 0

Outbound call problem! Unable to handle indication 13
by Skyler F 18 Jul '16

18 Jul '16

So I try to make an outbound call on my AllStar machine under a mikrotik router, and I get "Connection Failed". The /tmp/rpt_extnodes is fine, and it is reporting to AllStars nodelist and the stats server. Iax2 show registry is good. When I make an inbound connection to the node, it connects right up, however, when I make an outbound conenction, I get this big error on any node : channel.c:2447 ast_indicate_data: Unable to handle indication 13 for 'IAX2/173.82.59.253:4569-10526' The strange thing is that if an initial inbound connection is made, it is fine for outbound connections on that particular node number. So, 1) no outbound, only inbound AllStar connections 2) Outbound works to the particular node only if an initial inbound connection is made. This problem just started, and I have no idea what would be causing it. I DO have two nodes on the same IP, they are on different ports and I have the ports forwarded to the specefic devices respectively. 73 Skyler KD0WHB -- Skyler Fennell amsatnet.info KDØWHB electricity440(a)gmail.com

3 6

Record Connections?
by Bob 18 Jul '16

18 Jul '16

Is there a way to log connections from Allstar and Echolink nodes? The connections are displayed when monitoring CLI> Thanks, Bob k6ecm 73

1 0

New Dial installation asterisk is not running
by C B 17 Jul '16

17 Jul '16

Sorry if this question has been answered before i did look and could not find the answer. just built a all star node using Dial it is on a HP 5700. it appears that asterisk is not running when i type asterisk -r at the CLI it responds with Unable to connect to remote asterisk (does /var/run/asterisk.ctl exist?) if i type asterisk at the CLI then type asterisk -r asterisk runs for short time and responds with Disconnected from Asterisk server any help greatly appreciated. Chris

2 2

can boot DIAL on USB with UEFI
by REDBUTTON_CTRL 17 Jul '16

17 Jul '16

Hi All, trying to build a DIAL server with a usb drive on a newer pc with win 8. Yes I want out blow out win 8! Been having fun getting the pc to allow me to boot from usb. I think I finally got it to boot from my usb stick with the Dial image on it. But all I got was blank screen. I have been using this usb stick loading Dial on several older pcs with success. This is the firs pc with UEFI win 8 I have tried to wipe out and its not cooperating. any ideas on how to make this work? Thanks, Jon VA3RQ

2 3

Radio programming for RTCM in half-duplex mode
by Tom Hayward 16 Jul '16

16 Jul '16

I'm using an RTCM for a half-duplex link, adding Allstar to an existing repeater remotely. (We don't have Internet at the repeater site yet, but eventually the plan is to have the link at the repeater site in full-duplex mode.) I'm trying to deduce the canon method to program the radio. The repeater only transmits PL when the receiver is active, so with CTCSS on the link receiver I don't have to worry about courtesy tones or IDer getting through the link. I have the RTCM set for external CTCSS. What I think I need is the link radio programmed for TX 147.90 no PL RX 147.30 88.5 Hz CTCSS Then add txctcss in chan_voter, so that the link only transmits PL when there is audio on the link. I don't want the link IDer going through the repeater. As far as I can tell, there's no CTCSS DSP in the RTCM or chan_voter, so I need to use the radio's CTCSS. Is this correct? Tom KD7LXL

1 0

Re: [App_rpt-users] trouble connecting
by George Csahanin 16 Jul '16

16 Jul '16

Can't leave well enough alone. OK, downloaded the config from allstar to my box, asterisk runs, doesn't talk to the radio... Arrrrrrrghh! GeorgeC On 7/16/2016 10:28 AM, David McGough wrote: > Hi George, > > The most recent rpt_extnode lists still show you using port 4569. > > If you've switch the asterisk software and router at your end to 4570 (or > something else), you need to also change the port used in the web portal > (https://allstarlink.org/ ). > > 73, David KB4FXC > > > > On Sat, 16 Jul 2016, George Csahanin wrote: > >> Still some nodes that show online that I cannot connect to but I may >> have messed up something with the node list download in my hacking. The >> one I have been able to connect to has an entry in rpt.conf. But at >> least that connection is up, and it is the normal config. >> >> >> Thanks >> >> >> GeorgeC >> >> >> On 7/16/2016 10:04 AM, Steve Zingman wrote: >>> Great. >>> Glad you are up and running. >>> >>> 73, Steve N4IRS >>> >>> On 07/16/2016 10:02 AM, George Csahanin wrote: >>>> Steve, I just started poking in the router and saw that Verizon has >>>> services on port 4567, and took a wild guess that they may be >>>> blocking some stuff. Moved my node to 4570 and it all works. Just >>>> about 5 minutes ago. >>>> >>>> >>>> Go figure. >>>> >>>> >>>> GeorgeC >>>> >>>> >>>> On 7/16/2016 9:52 AM, Steve Zingman wrote: >>>>> George, >>>>> What is the result of the Asterisk CLI command: iax2 show registry >>>>> >>>>> Lets start there >>>>> >>>>> On 07/16/2016 09:48 AM, George Csahanin wrote: >>>>>> Stumped, maybe because I've played with this stuff a lot over the >>>>>> last 7 years...but...my ISP just changed my IP address. No longer >>>>>> can connect to anything and the last extnodes file was right before >>>>>> they made the change Thursday night. Might have been Wednesday, >>>>>> doesn't matter. There was nothing to change in the rpt.conf file, >>>>>> everything looks normal except the only obvious thing is that I'm >>>>>> not seeing rpt_extnodes updating. I put an entry in rpt.conf for a >>>>>> node I normally connect to (27891) and get /__auto_congest: >>>>>> Auto-congesting call due to slow response// >>>>>> /Checked port forwarding rules on the Verizon router, and is >>>>>> normal. I also *can* connect to usual nodes via the echolink >>>>>> port./(W8VT is 27849 and 606945 echo. echo works) >>>>>> >>>>>> /Really stumped but operating under a medically induced handicap >>>>>> (fever). Anybody have any words of wisdom as to what I may be >>>>>> overlooking. Worked fine until Verizon re-did everything that night. / >>>>>> >>>>>> /Again, thanks for bearing with me but this bug has me down and >>>>>> this isn't looking too clear to me. >>>>>> >>>>>> GeorgeC >>>>>> W2DB >>>>>> 2360/ >>>>>> >>>>>> / >>>>>> >>>>>> >>>>>> _______________________________________________ >>>>>> App_rpt-users mailing list >>>>>> App_rpt-users(a)ohnosec.org >>>>>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>> >>>>>> To unsubscribe from this list please visithttp://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" >>>>>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. >>>>> -- >>>>> "Anything is possible if you don't know what you are talking about." >>>>> 1st Law of Logic >>> -- >>> "Anything is possible if you don't know what you are talking about." >>> 1st Law of Logic >> >

2 1