- App_rpt-users - lists.keekles.org

How concerned should I be?
by Robert Newberry 18 Nov '15

18 Nov '15

So I've been on my never ending quest of learning linux. So I was reading about simpleusb and usbradio...please no debates versus quality! I came across a reference to the top command and if asterisk takes up more than 20% or more I should consider simpleusb. Well one of my sites running two nodes which is having audio issues! Is swinging from 20-40% never dipping below 20% Thanks N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812, 42086

3 2

Raspberry pi dial uri eeprom broken?
by Scott Weis 17 Nov '15

17 Nov '15

I just set up a new node using a raspberry pi and the dial distribution. I have a uri with an eeprom in it. It was tuned and config saved on the EEPROM. On startup I get the message USB Adapter has no EEPROM installed or Checksum BAD on channel usbXXXXX. I then retuned the URI and did a radio tune save and asterisk said it was saving to the eeprom. Then reloaded asterisk and go the same message as above. Did the whole procedure again using another URI and EEPROM. SAME PROBLEM. Tried both URIs on my x86 acid box and it worked fine. So is this a dial on raspberry pi problem or does this happen on x86 too? Thanks & 73, Scott KB2EAR

2 2

FW: Asterisk reboots-Clocking error
by Mark DuMoulin ＠ WB2ERS 17 Nov '15

17 Nov '15

From: Mark DuMoulin Sent: Tuesday, November 17, 2015 11:21 AM To: 'Tim Sawyer' <tisawyer(a)gmail.com>; Mark DuMoulin @ WB2ERS <wb2ers(a)metcom.com> Cc: app_rpt-users(a)ohnosec.org Subject: RE: [App_rpt-users] Asterisk reboots-Clocking error Tim, We put the macro in place. Asterisk was reloaded and Hard booted. Still no connection between the two “repeaters” in rpt.conf. Is [node] supposed to be part of this? Mark From: Tim Sawyer [mailto:tisawyer@gmail.com] Sent: Friday, November 13, 2015 6:53 PM To: Mark DuMoulin @ WB2ERS <wb2ers(a)metcom.com<mailto:wb2ers@metcom.com>> Cc: app_rpt-users(a)ohnosec.org<mailto:app_rpt-users@ohnosec.org> Subject: Re: [App_rpt-users] Asterisk reboots-Clocking error Reading you post again; if what you want to do is just have an RTCM and a URI you have to have two nodes. One for the URI and one for the RTCM. rpt.conf: [500] rxchannel=SimpleUSB/500 duplex=2 # for repeater ... # connect URI to RTCM at startup startup_macro=*3501 ... [501] rxchannel=Voter/501 duplex=2 #for repeater ... voter.conf: [501] SITE1 = passwrd1,transmit SITE2 = passwrd2 SITE3 = passwrd3 buflen = 250 plfilter = y On Fri, Nov 13, 2015 at 3:45 PM, Tim Sawyer <tisawyer(a)gmail.com<mailto:tisawyer@gmail.com>> wrote: Not sure what you want to do, but assuming you want to tie a bunch of controllers together, replacing 420 links for example, you don't need radbridge to bridge RTCMs. Just put all the RTCM under one node in voter.conf. The secret here is mixminus which stops a second repeat path back to the RTCM. rpt.conf: rxchannel=Voter/501 duplex=0 linktolink = yes voter.conf: [501] SITE1 = passwrd1,transmit,nodeemp,noplfilter SITE2 = passwrd2,transmit,nodeemp,noplfilter SITE3 = passwrd3,transmit,nodeemp,noplfilter buflen = 250 mixminus = y plfilter = n On Fri, Nov 13, 2015 at 9:47 AM, Mark DuMoulin @ WB2ERS <wb2ers(a)metcom.com<mailto:wb2ers@metcom.com>> wrote: Hello All, I am running ACID with URI connected. I also have repeaters using RTCM units. When I attempt to use radbridge.conf to combine RTCM and URI as shown below: [general] instance1 = Voter/rtcm,Radio/usb This is what happens: [Nov 13 12:37:01] NOTICE[12655]: chan_usbradio.c:3273 usbradio_request: Already have a call (chan 0x91b4d18) on the usb channel [Nov 13 12:37:03] NOTICE[12613]: app_rpt.c:22002 rpt_master: RPT thread restarted on 1448 [Nov 13 12:37:03] WARNING[12613]: app_rpt.c:22014 rpt_master: rpt_thread restarted on node 1448 -- Re-Loading config for repeater 1448 [Nov 13 12:37:03] NOTICE[12656]: chan_usbradio.c:3273 usbradio_request: Already have a call (chan 0x91b4d18) on the usb channel [Nov 13 12:37:05] ERROR[12613]: app_rpt.c:21997 rpt_master: Continual RPT thread restarts, killing Asterisk Does anyone have any thoughts as to why this is occurring or a different approach on combining the URI and RTCM end points? Mark DuMoulin WB2ERS Wb2ers(a)metcom.com<mailto:Wb2ers@metcom.com> C 800-410-3130<tel:800-410-3130> _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org<mailto:App_rpt-users@ohnosec.org> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. -- -- Tim -- -- Tim

1 0

Asterisk reboots-Clocking error
by Mark DuMoulin ＠ WB2ERS 16 Nov '15

16 Nov '15

Hello All, I am running ACID with URI connected. I also have repeaters using RTCM units. When I attempt to use radbridge.conf to combine RTCM and URI as shown below: [general] instance1 = Voter/rtcm,Radio/usb This is what happens: [Nov 13 12:37:01] NOTICE[12655]: chan_usbradio.c:3273 usbradio_request: Already have a call (chan 0x91b4d18) on the usb channel [Nov 13 12:37:03] NOTICE[12613]: app_rpt.c:22002 rpt_master: RPT thread restarted on 1448 [Nov 13 12:37:03] WARNING[12613]: app_rpt.c:22014 rpt_master: rpt_thread restarted on node 1448 -- Re-Loading config for repeater 1448 [Nov 13 12:37:03] NOTICE[12656]: chan_usbradio.c:3273 usbradio_request: Already have a call (chan 0x91b4d18) on the usb channel [Nov 13 12:37:05] ERROR[12613]: app_rpt.c:21997 rpt_master: Continual RPT thread restarts, killing Asterisk Does anyone have any thoughts as to why this is occurring or a different approach on combining the URI and RTCM end points? Mark DuMoulin WB2ERS Wb2ers(a)metcom.com C 800-410-3130

2 4

Interface existing
by Robert Newberry 16 Nov '15

16 Nov '15

I'm wondering what other people do if you have a repeater with an existing controller. I have a site that the repeater owner would like to be able to continue to use the existing controller, but be on allstar. My thoughts were basically set it up like a simplex radio. Get the rx audio from the repeater and tie into mic audio at the repeater. Has anyone done this? N1XBM Apparare Scientor Paratus Communicare Allstar Node # 27086, 41540, 41812, 42086

2 1

Why no callsign validation
by Skyler F 16 Nov '15

16 Nov '15

On AllStar link, you don't have to send in a PDF anymore of your license. If I remember correctly, I had to send a picture of my license at one point. Personally I don't care, I find it a lot easier to not have to send in this, but is that why EchoLink now does not want people to have it on their node anymore? I just think it might be easy for unlicensed trolls to get on the air under someone else's call. I have personally validated 3 call-signs for various clubs and a friend and it was pretty easy to register because I didn't even need to ask the club for their license electronic copy / photo. Again, I don't have a problem with this, and I believe if you can buy a 30 dollar chinese radio, and get on the air without a call-sign, it's not much different doing the same on the internet with VoIP, but I want to know what other people think about the subject. Is this one of the reasons why Dave cameron banned AllStar from IRLP? Skyler KD0WHB

2 1

list of additional software for allstar /app_rpt
by Pete M 16 Nov '15

16 Nov '15

I was syncing my node shark installation this morning and was blasted by a question... Is there a list of add-on software /script/ dashboard that can be used with allstar/app_rpt somewhere? many here knows a lot about all those nice script and add-ons.. But for someone that is not connected to this list. It can be hard to find info on those unless you them by name and then can google it. It would be nice to have a list somewhere on the allstar web page about what is available and maybe a link to where they are located. Or am I again late on this and was not cleaver enough to find it? And one last thing.. thanks to all that do a marvelous job on this project.. (Yeah I know sound like some butt liking.. but still I mean it.. The praise not the butt linking.. )

1 0

SSB voter
by Skyler Fennell 15 Nov '15

15 Nov '15

Is it possible to vote with SSB? I picture a simplex HF setup with voters / simulcast all around the world linked with the web. Any similar ideas? KDØWHB

2 1

Weird URI problem
by KH6KL 15 Nov '15

15 Nov '15

11.14.2015 I'm not sure which board to post this on... My repeater is a Motorola R1225, 25Watts, w/ PL. The computer is a BeagleBoneBlackC. I'm only using the COS, PTT, Rx Audio, Mic and ground. This system has been working on the AllStar Network since May 2015. About 2 months ago a weird problem started: The Xm hangs on, but PTT voltage is at 5v. The URI red led is off. If I just wait the timeout timer kills the Xm but the the PTT doesn't work until I reset the 1225. The Rptr Rx led is off the whole time, so there's no incoming signal. This only happens when the URI is connected to the accessory plug. I put my spare R1225 on-line and the same thing happens. Note: I have everything working off of an Astron SS30 power supply. I looked for ground loops, but didn't find any. I borrowed an URI and the system worked perfectly. I returned the URI and put the repeater on-line/stand-alone for two weeks with no problems. I sent the URI back to DMK engineering and it passed their test, so it was returned to me. I put it on line and the same problem started again. I swapped the the two URIs and my machine worked perfectly but the other machine started to kerchunking by itself. I returned the borrowed URI, and put my machine on-line/stand-alone. I would like to know if anyone has had this problem and what was your solution. I called DMK engineering to see if they would warranty the URI, no decision yet, but I ordered a new URI to get this node working. Aloha, Pat KH6KL

2 1

UFW Firewall Blocking unwanted traffic
by Loren Tedford 14 Nov '15

14 Nov '15

I am not aware of how to block a node number if their is a problem however here is what i came up with for the Debian or Dial Distribution or if your running Ubuntu Server etc.. I install ufw here is some command line tips sudo apt-get update && sudo apt-get upgrade sudo apt-get install ufw sudo ufw allow {Port Number} I dont suggest using default ports with ssh because they get hammed really hard and on my data center I do use default port however i also run Fail2ban on the server I wont cover fail2ban because its pretty easy and self explanatory for the most part.. Example using all default ports for allstar sudo ufw allow 222/tcp <-- Ssh port sudo ufw allow 4569/udp <-- Iax port for allstar sudo ufw allow 5060/udp <--- For sip if you have to use it I always stay clear of this particular port it gets hammered alot harder easier to break sip traffic.. sudo ufw allow 5198/udp <--- Echolink port sudo ufw allow 5199/udp <-- Another echolink port.. sudo ufw allow 5200/tcp <-- And yet another echolink port.. If you use allmon and would like to access it sudo ufw allow 80/tcp sudo ufw default allow outgoing sudo ufw default deny incoming sudo systemctl start ufw sudo systemctl enable ufw here is the documentation that helped me out from linode.. https://www.linode.com/docs/security/firewalls/configure-firewall-with-ufw Mark KC9ZHR helped me create a script that has pretty much cured most of my hacker issues here is that script.. Look it over and put a # over ports you wish to keep out of the ban list.. This script has solved about 90% of my hacker issues on sip ports and iax ports.. So far no one has been successful but i am always looking to keep the system secure the best i can.. http://kc9zhv.com/iso/ufwblocklist Here is how i run it on my allstar servers.. wget http://kc9zhv.com/iso/ufwblocklist sudo ./ufwblocklist Hope this helps anyone out their dealing with unwanted traffic.. Oh almost for got if their is an ip that you wish to allow you can add via typing sudo ufw allow from 10.10.10.1 or you can sudo ufw allow from 10.10.10.1/24 Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com Main Line:1-631-686-8878 Option 1 for Loren. Fax Line 1:1-618-551-2755 Fax Line 2:1-631-686-8892 (New Fax line) Cell: 618-553-0806 http://www.lorentedford.com http://www.kc9zhv.com http://hub.kc9zhv.com

1 0