- App_rpt-users - lists.keekles.org

Re: [App_rpt-users] Squelch Tail Elimination
by Bryan Fields 29 Mar '15

29 Mar '15

I believe he's using the RTCM, so the usbradio commands will not work. On March 29, 2015 12:33:30 PM EDT, Ken <ke2n(a)cs.com> wrote: >There are two squelch tails. One in the user’s receiver which can be >eliminated by using tone squelch and turning off the PL some time >before dropping the carrier. Some commercial rigs respond to the >reverse phase tone burst. That is unusual in amateur rigs I think. And >some amateur rigs require the tone to be turned off longer that the >app_rpt default. This all has to do with the squelch tail being >generated in the user’s receiver. > > > >But if you want the *repeater* not to transmit a squelch tail - from >its own receiver - then you need: > > Rxsquelchdelay in usbradio.con > >as previously discussed in : > ><http://ohnosec.org/pipermail/app_rpt-users/2014-April/009175.html> >http://ohnosec.org/pipermail/app_rpt-users/2014-April/009175.html > > > >for example > >rxsquelchdelay=50 ; delayline in ms, carrier squelch tail eliminator > > > >this requires use of the usbradio channel driver. > > > >73 > >Ken > > > > > > > >From: R. Wayne [mailto:allstar@controlservers.net] >Sent: Sunday, March 29, 2015 1:34 AM >To: app_rpt-users(a)ohnosec.org >Subject: [App_rpt-users] Squelch Tail Elimination > > > >After relocating our MSF 5000 to a new location and adjusting the >squelch as low as we could reliably go we noticed that we have a >squelch tail. Our coordination requires that we don’t. It appears that >the MSF has a fixed squelch tail elimination method an no control other >than cranking up the squelch again. This is surprising since we use PL >encode / decode. I would think that the PL would mute as soon as the >user unkeys. > > > >With this said is there anything in Allstar that would help with this >situation? > > > >Wayne > > > >------------------------------------------------------------------------ > >_______________________________________________ >App_rpt-users mailing list >App_rpt-users(a)ohnosec.org >http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > >To unsubscribe from this list please visit >http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll >down to the bottom of the page. Enter your email address and press the >"Unsubscribe or edit options button" >You do not need a password to unsubscribe, you can do it via email >confirmation. If you have trouble unsubscribing, please send a message >to the list detailing the problem. -- Bryan Fields 727-409-1194 http://bryanfields.net

2 1

Re: [App_rpt-users] Squelch Tail Elimination
by Bryan Fields 29 Mar '15

29 Mar '15

The RTCM has a manual squelch threshold pot. It will function as a bilevel squelch with a strong signal. Are you feeding the discriminator audio to the RTCM and have it set up as such? If you cannot use discriminator audio you may need an audio delay board in place as well. This is not a standard configuration if you're feeding non discriminator audio to the RTCM. On March 29, 2015 10:01:54 AM EDT, "R. Wayne" <allstar(a)controlservers.net> wrote: >But as we said we are using a RTCM. > >From: REDBUTTON_CTRL >Sent: Sunday, March 29, 2015 5:09 AM >To: app_rpt-users(a)ohnosec.org >Subject: Re: [App_rpt-users] Squelch Tail Elimination > >The short answer is yes. > >What you need to do is bring out raw discriminator to the URI or USB >fob. Then configure youfr node for USB radio to have > >Carrierfrom = dsp and ctcss from = dsp. >you also need to set the rx demod to flat. > > >[usbnode_num] > >hdwtype=0 >rxboost=1 >txboost=1 >rxctcssrelax=1 >txctcssdefault=131.8 ; default pl tone >rxctcssfreqs=131.8 ;rx pl tone >txctcssfreqs=131.8 ;tx pl tone if used >;rxctcssoverride=0 >carrierfrom=dsp ;carrier squelch detection >ctcssfrom=dsp ; pl tone detection >rxdemod=flat >txprelim=yes >txlimonly=no >txtoctype=phase >txmixa=voice >txmixb=no >invertptt=0 >duplex=0 >rxondelay=0 >rxnoisefiltype=0 >eeprom=0 > > >Save your settings and restart your Allstar node so the changes take >affect. >Do your audio calibrations. > >Then you will need to set the carrier squelch. Typically the default >squelch setting in Allstar is below the threshold. So you will get >squelch crashes. > >Do a "radio tune rxsquelch" at the cli with no signal at the receiver. >It will return the current squelch setting and the current squelch >level. > >*CLI> radio tune rxsquelch >Current Signal Strength is 788 >Current Squelch setting is 500 > >If the squelch level is below the signal strength then the carrier >squelch is open. >Set the squelch higher than the signal strength by about 80-100 points. > >*CLI> radio tune rxsquelch 820 <enter> > >Try the squelch. It should give you a "fast squelch" for signals that >have 20 db quieting or better. >then test the threshold and see how weak signal will open the squelch. >You may have to tweak the squelch to liking. > >Once you have the squelch set correctly then save thew settings. > >*CLI> radio tune save. > >You should be good to go. > >Jon VA3RQ > > > > > > > > >On 3/29/2015 1:33 AM, R. Wayne wrote: >After relocating our MSF 5000 to a new location and adjusting the >squelch as low as we could reliably go we noticed that we have a >squelch tail. Our coordination requires that we don’t. It appears that >the MSF has a fixed squelch tail elimination method an no control other >than cranking up the squelch again. This is surprising since we use PL >encode / decode. I would think that the PL would mute as soon as the >user unkeys. > >With this said is there anything in Allstar that would help with this >situation? > > Wayne > > > >_______________________________________________ >App_rpt-users mailing list >App_rpt-users(a)ohnosec.org >http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > >To unsubscribe from this list please visit >http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll >down to the bottom of the page. Enter your email address and press the >"Unsubscribe or edit options button" >You do not need a password to unsubscribe, you can do it via email >confirmation. If you have trouble unsubscribing, please send a message >to the list detailing the problem. > >-------------------------------------------------------------------------------- >_______________________________________________ >App_rpt-users mailing list >App_rpt-users(a)ohnosec.org >http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > >To unsubscribe from this list please visit >http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll >down to the bottom of the page. Enter your email address and press the >"Unsubscribe or edit options button" >You do not need a password to unsubscribe, you can do it via email >confirmation. If you have trouble unsubscribing, please send a message >to the list detailing the problem. > >------------------------------------------------------------------------ > >_______________________________________________ >App_rpt-users mailing list >App_rpt-users(a)ohnosec.org >http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > >To unsubscribe from this list please visit >http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll >down to the bottom of the page. Enter your email address and press the >"Unsubscribe or edit options button" >You do not need a password to unsubscribe, you can do it via email >confirmation. If you have trouble unsubscribing, please send a message >to the list detailing the problem. -- Bryan Fields 727-409-1194 http://bryanfields.net

1 0

signal level good enough for a URI-X?
by pete M 29 Mar '15

29 Mar '15

Anyone can confirm if a signal level of 70~90mVrms with an Output impedance: 1kΩ or less Coupling: AC coupling Frequency response: ±2.5dB at 10~3000Hz is enough to drive a URI or should I use the included pre amp in the URI-X? trying to use the RD line from a tkr-750 to do USBRadio control of a node. thanks And while I am at it, pin 10 and 11 of the tkr both are signal input, 10 is TD (tx data) and 11 is TA (tx audio) If I feed one side of the output to the pin 10 (TD) for tone signal and the other side to (TA) and apply repeated audio would that make sens? Cause I did try that and It did not seem to work.. thanks again for your input Pierre VE2PF

3 5

Re: [App_rpt-users] Simplex node
by Kevin Custer 28 Mar '15

28 Mar '15

On 3/27/2015 9:55 AM, Doug Crompton wrote: > ------------snip------------- > Although there has been a slight improvement in usbradio in the latest > svn it still does not have the exceptionally clean audio that > simpleusb does. > > *73 Doug > WA3DSP > http://www.crompton.com/hamradio* Doug, I have seen this statement from you many times. I have about 50 installations of usbradio where I don't experience these issues you claim. Will you please quantify your statement as to whether or not the issues you claim are for the BBB release, or any ACID release - and also if it pertains to only the BBB or any computer platform. I have baseline performance specifications using usbradio and PC hardware. While the performance does change slightly due to the exact radio adapter device, the overall response and distortion specifications are very consistent when using G.722 -u-law. My performance specifications show that any distortions or response issues contributed directly by app_rpt, any channel driver, or the radio interface are well below detection by the human ear. In fact, I can guarantee you that more distortion is generally experienced when running simpleusb audio through any radio. In other words, there is more distortion and response issues because of the radio then from this application and its supporting hardware in usbradio. I'll apologize that I had to hijack this thread from the arm-allstar email group and re-post it here - because I'm no longer allowed to participate in your group directly. As Allan Crites would say - "Your turn"... Kevin Custer - W3KKC

4 5

Changing audio level of link
by Andy Wittman 27 Mar '15

27 Mar '15

Hello All, I am curious to know if there is a setting I can adjust to increase the volume of audio coming in from a link. My rx and tx levels are good, when turning on parrot mode everything sounds great, but when I link in to a repeater, the incoming audio is very low. On the other side of the conversation I receive good audio reports from my side. I am using a simplex node running on the BBB with a Baofeng 888. I switched it and my HT to WFM but the linked audio is still very low. Thanks in advance, Andy KK4ZKP

2 3

Cannot Connect to Node
by Jamey Wright 27 Mar '15

27 Mar '15

I am having issues with a new node I recently set up. I had post a couple of weeks ago about having issues with WebTransceiver connecting to it. At the time it was improperly registering (showing up using the wrong IP address). That problem has been corrected but I still cannot access it using WebTransceiver. Using the AllStar portal, I go to Network-->All Online Nodes and my node number does not appear in the list. When I go to Network-->System-Wide Node List, my node appears and is highlighted green. When I go to Network-->Node Status-->27981 I get a black page with a white rectangular box with: "AllStar Link [surrounding node 27981] status as of 03/27/15 02:31:50 GMT" I checked the iax.conf file and the node number and password are correct. No clue where to check next. Thanks Jamey WR4JW

3 5

Re: [App_rpt-users] Macro and DTMF format in rpt.conf
by Jeff Carrier 26 Mar '15

26 Mar '15

here is an example [macro28299] 317 = *428257*5317# ;Disconnect Remote you'd send *5317 to call that macro. Sorry I hit send prematurely earlier. On Thu, Mar 26, 2015 at 7:44 PM, Jeff Carrier <k0jsc.jeff(a)gmail.com> wrote: > here is an example > > [macro28299] > > 317 = *428257*5317# ;Disconnect Remote > > On Thu, Mar 26, 2015 at 7:07 PM, kk6ecm <kk6ecm(a)gmail.com> wrote: > >> This is a question I've had for some time now... DTMF 577 would >> appear in rpt.conf as 977? >> >> >> >> thanks, >> >> Bob >> >> kk6ecm >> >> >> ------------------------------ >> >> *From:* app_rpt-users-bounces(a)ohnosec.org [mailto: >> app_rpt-users-bounces(a)ohnosec.org] *On Behalf Of *Jeff Carrier >> *Sent:* Thursday, March 26, 2015 3:39 PM >> *To:* r gilson >> *Cc:* app_rpt-users(a)ohnosec.org >> *Subject:* Re: [App_rpt-users] App_rpt-users Digest, Vol 73, Issue 46 >> >> >> >> "5xx" is "usually" a macro unless the macro digit has been changed. >> >> >> >> On Thu, Mar 26, 2015 at 3:13 PM, r gilson <rgilson14215(a)yahoo.com> wrote: >> >> I understand the *77 to do a reboot but where does the *577 come in . I >> do not see the "5" in either stanza? Thanks. >> >> Ron >> >> >> ------------------------------ >> >> *From:* "app_rpt-users-request(a)ohnosec.org" < >> app_rpt-users-request(a)ohnosec.org> >> *To:* app_rpt-users(a)ohnosec.org >> *Sent:* Thursday, March 26, 2015 12:00 PM >> *Subject:* App_rpt-users Digest, Vol 73, Issue 46 >> >> >> Send App_rpt-users mailing list submissions to >> app_rpt-users(a)ohnosec.org >> >> To subscribe or unsubscribe via the World Wide Web, visit >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >> or, via email, send a message with subject or body 'help' to >> app_rpt-users-request(a)ohnosec.org >> >> You can reach the person managing the list at >> app_rpt-users-owner(a)ohnosec.org >> >> When replying, please edit your Subject line so it is more specific >> than "Re: Contents of App_rpt-users digest..." >> >> >> Today's Topics: >> >> 1. Server "reboot" command via radio and DTMF? (kk6ecm) >> 2. Re: Server "reboot" command via radio and DTMF? (Bryan D. Boyle) >> 3. Re: Server "reboot" command via radio and DTMF? >> ((KP4TR)Ramon Gonzalez) >> 4. AllStar Asterisk on Raspberry Pi 1 and 2 (Steve Zingman) >> >> >> ---------------------------------------------------------------------- >> >> Message: 1 >> Date: Wed, 25 Mar 2015 17:47:49 -0700 >> From: "kk6ecm" <kk6ecm(a)gmail.com> >> To: "'Allstar'" <app_rpt-users(a)ohnosec.org> >> Subject: [App_rpt-users] Server "reboot" command via radio and DTMF? >> Message-ID: <23F122DF83104A179AE2E3B0D5EAEBA8@ThePykesHP> >> Content-Type: text/plain; charset="us-ascii" >> >> Two questions: >> >> 1) Is there a way to perform a command line "reboot" from a radio using >> DTMF? It seems the COP are for controlling within Asterisk. I am aware of >> COP,1 to warm boot asterisk. >> >> 2) Is there a reason this is not a good idea? >> >> Thanks, >> Bob >> kk6ecm >> >> >> >> ------------------------------ >> >> Message: 2 >> Date: Wed, 25 Mar 2015 21:47:24 -0400 >> From: "Bryan D. Boyle" <bdboyle(a)bdboyle.com> >> To: kk6ecm <kk6ecm(a)gmail.com> >> Cc: Allstar <app_rpt-users(a)ohnosec.org> >> Subject: Re: [App_rpt-users] Server "reboot" command via radio and >> DTMF? >> Message-ID: <F4F7A08D-165C-473F-B1F8-6E7D317A753B(a)bdboyle.com> >> Content-Type: text/plain; charset="us-ascii" >> >> write a script that gets called from a complex dtmf command. >> >> >> >> -- >> Bryan >> Sent from my iPhone 5...No electrons were harmed in the sending of this >> message. >> >> >> >> > On Mar 25, 2015, at 20:47, kk6ecm <kk6ecm(a)gmail.com> wrote: >> > >> > Two questions: >> > >> > 1) Is there a way to perform a command line "reboot" from a radio using >> > DTMF? It seems the COP are for controlling within Asterisk. I am aware >> of >> > COP,1 to warm boot asterisk. >> > >> > 2) Is there a reason this is not a good idea? >> > >> > Thanks, >> > Bob >> > kk6ecm >> > >> > _______________________________________________ >> > App_rpt-users mailing list >> > App_rpt-users(a)ohnosec.org >> > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >> > >> > To unsubscribe from this list please visit >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll >> down to the bottom of the page. Enter your email address and press the >> "Unsubscribe or edit options button" >> > You do not need a password to unsubscribe, you can do it via email >> confirmation. If you have trouble unsubscribing, please send a message to >> the list detailing the problem. >>

1 0

Re: [App_rpt-users] App_rpt-users Digest, Vol 73, Issue 46
by r gilson 26 Mar '15

26 Mar '15

I understand the *77 to do a reboot but where does the *577 come in . I do not see the "5" in either stanza? Thanks.Ron From: "app_rpt-users-request(a)ohnosec.org" <app_rpt-users-request(a)ohnosec.org> To: app_rpt-users(a)ohnosec.org Sent: Thursday, March 26, 2015 12:00 PM Subject: App_rpt-users Digest, Vol 73, Issue 46 Send App_rpt-users mailing list submissions to app_rpt-users(a)ohnosec.org To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request(a)ohnosec.org You can reach the person managing the list at app_rpt-users-owner(a)ohnosec.org When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..." Today's Topics: 1. Server "reboot" command via radio and DTMF? (kk6ecm) 2. Re: Server "reboot" command via radio and DTMF? (Bryan D. Boyle) 3. Re: Server "reboot" command via radio and DTMF? ((KP4TR)Ramon Gonzalez) 4. AllStar Asterisk on Raspberry Pi 1 and 2 (Steve Zingman) ---------------------------------------------------------------------- Message: 1 Date: Wed, 25 Mar 2015 17:47:49 -0700 From: "kk6ecm" <kk6ecm(a)gmail.com> To: "'Allstar'" <app_rpt-users(a)ohnosec.org> Subject: [App_rpt-users] Server "reboot" command via radio and DTMF? Message-ID: <23F122DF83104A179AE2E3B0D5EAEBA8@ThePykesHP> Content-Type: text/plain; charset="us-ascii" Two questions: 1) Is there a way to perform a command line "reboot" from a radio using DTMF? It seems the COP are for controlling within Asterisk. I am aware of COP,1 to warm boot asterisk. 2) Is there a reason this is not a good idea? Thanks, Bob kk6ecm ------------------------------ Message: 2 Date: Wed, 25 Mar 2015 21:47:24 -0400 From: "Bryan D. Boyle" <bdboyle(a)bdboyle.com> To: kk6ecm <kk6ecm(a)gmail.com> Cc: Allstar <app_rpt-users(a)ohnosec.org> Subject: Re: [App_rpt-users] Server "reboot" command via radio and DTMF? Message-ID: <F4F7A08D-165C-473F-B1F8-6E7D317A753B(a)bdboyle.com> Content-Type: text/plain; charset="us-ascii" write a script that gets called from a complex dtmf command. -- Bryan Sent from my iPhone 5...No electrons were harmed in the sending of this message. > On Mar 25, 2015, at 20:47, kk6ecm <kk6ecm(a)gmail.com> wrote: > > Two questions: > > 1) Is there a way to perform a command line "reboot" from a radio using > DTMF? It seems the COP are for controlling within Asterisk. I am aware of > COP,1 to warm boot asterisk. > > 2) Is there a reason this is not a good idea? > > Thanks, > Bob > kk6ecm > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

3 2

AllStar Asterisk on Raspberry Pi 1 and 2
by Steve Zingman 26 Mar '15

26 Mar '15

Leon, Now that's a blast from the distant past. :) It's built from the SVN. Asterisk is at 1.4.23 That's the last version Jim is supporting app_rpt on. From what I remember, Jim says that later version of Asterisk break things app_rpt rely on. 73, Steve N4IRS > good deal steve > been out of touch what * version are you guys using and any plans to > move to more current versions? > 73 leon wa4zlw > On 3/26/2015 11:06 AM, Steve Zingman wrote: > I've updated the scripts and tar files for installing AllStar Asterisk > on the Raspberry Pi platforms. > > The Pi 1 is at <https://github.com/N4IRS/AllStar/blob/master/rpi1.tar> > The Pi 2 is at <https://github.com/N4IRS/AllStar/blob/master/rpi2.tar> > > All of the scripts, patches and platform specific files are at: > <https://github.com/N4IRS/AllStar> > > 73, Steve N4IRS > 73, Steve N4IRS -- "Anything is possible if you don't know what you are talking about." 1st Law of Logic

1 0

AllStar Asterisk on Raspberry Pi 1 and 2
by Steve Zingman 26 Mar '15

26 Mar '15

I've updated the scripts and tar files for installing AllStar Asterisk on the Raspberry Pi platforms. The Pi 1 is at <https://github.com/N4IRS/AllStar/blob/master/rpi1.tar> The Pi 2 is at <https://github.com/N4IRS/AllStar/blob/master/rpi2.tar> All of the scripts, patches and platform specific files are at: <https://github.com/N4IRS/AllStar> 73, Steve N4IRS -- "Anything is possible if you don't know what you are talking about." 1st Law of Logic

2 1