- App_rpt-users - lists.keekles.org

QUAD PCI Radio Card Configuration
by Chris Andrist 09 Feb '14

09 Feb '14

I have a quad pci radio card, but am unable to get app_rpt to recognize it and not crash asterisk. Can someone point me to some detailed configuration that already has all 4 ports configured? I have already looked at /usr/src/astsrc/config/pciradio it hasn't got me anywhere. Regards, Chris Andrist, KC7WSU

1 0

dmtf desactive
by ea8ee 09 Feb '14

09 Feb '14

finally got the audio yaesu we receive seems to change usb dsp was decisive but now consiguimos the receiver to listen Radio DMTF there any parameter by which to see any possible change to make them work properly DMTF thanks for the help and support

1 0

Allstar parallel port (was source of USB CM108 FOBs - CHEAP)
by K&R Yoksh 09 Feb '14

09 Feb '14

Geez, sorry to waste your time with a reply, Jim. Do you already know how to use Google?http://ohnosec.org/drupal/node/17773,KyleK0KN--- Original Message --- I already know how to build a simple transistor switch.... How do you set up Asterisk to use the parallel port? What commands where? 73 Jim W7RY On 2/8/2014 1:34 PM, K&R Yoksh wrote: > Hello Andrew, > > In case George doesn't have anything written up for parallel port > operation: > http://www.qsl.net/k0kn/plri.html > > There are several circuits detailed here, from the simplest discrete > transistor type, to a transistor IC type that can support multiple > radios. > > You can also use an off-the-shelf IRLP board, should you have one > laying around. The DTMF decoder is not supported by Asterisk (Asterisk > uses DSP techniques to decode DTMF), so I dropped the MT8870 from my > schematics. > > At it's simplest, all you'd really need is one NPN transistor for PTT > (active high from parallel port, active low to activate PTT), and one > PNP transistor for COS (if active high from radio). If your radio uses > active low COS, I'd buffer with two transistors (PNP to NPN), rather > than directly connecting the radio to the PC. > > I'd suggest using active low at the parallel port inputs. > > 73 and good luck. > > Kyle > K0KN > Allstar 2210-2219 > > > --- Original Message --- > > Hello George, > > Do you have it documented anywhere how you configure the parallel port > for > COR and PTT? I'd love to see how you have it configured? > > Thanks! > > On Saturday, February 8, 2014, George Csahanin <george at dyb.com> wrote: > >> I bought some CM108 fobs on EBAY for $0.99 each. He has a s***load of >> them. Not knowing if they'd be real CM108 I waited till I got them to >> send >> this note. The USB ID is 08dc:000c the real thing. >> >> The last four nodes I built up use D945 motherboards which have parallel >> ports, which I use for COS/PTT and the USB fob only does audio. No >> need to >> modify them for PTT and COS, etc. >> >> Anyhow, the EBAY auction is 300503465055 OR click this >> link<http://www.ebay.com/itm/300503465055?ssPageName=STRK:MEWNX:IT&_trksid=p3984…> >> >> Seller's store is circle607. They're in Hong Kong. But the postage was >> under $1.20 for all ten. >> >> I stocked up simply because they work so well, cost so little, and not >> sure when they will stop being available. (hoarding 101) >> >> GeorgeC >> W2DB >> Allstar 2360 > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users at ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll > down to the bottom of the page. Enter your email address and press the > "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message > to the list detailing the problem.

3 2

Yaesu FT and URI DMK
by ea8ee 09 Feb '14

09 Feb '14

Someone is using Yaesu FT with URI and could send me the file usbradio thanks in advance

1 0

source of USB CM108 FOBs - CHEAP
by George Csahanin 09 Feb '14

09 Feb '14

I bought some CM108 fobs on EBAY for $0.99 each. He has a s***load of them. Not knowing if they’d be real CM108 I waited till I got them to send this note. The USB ID is 08dc:000c the real thing. The last four nodes I built up use D945 motherboards which have parallel ports, which I use for COS/PTT and the USB fob only does audio. No need to modify them for PTT and COS, etc. Anyhow, the EBAY auction is 300503465055 OR click this link Seller’s store is circle607. They’re in Hong Kong. But the postage was under $1.20 for all ten. I stocked up simply because they work so well, cost so little, and not sure when they will stop being available. (hoarding 101) GeorgeC W2DB Allstar 2360

6 8

Allstar parallel port (was source of USB CM108 FOBs - CHEAP)
by K&R Yoksh 09 Feb '14

09 Feb '14

Hello Andrew, In case George doesn't have anything written up for parallel port operation: http://www.qsl.net/k0kn/plri.html There are several circuits detailed here, from the simplest discrete transistor type, to a transistor IC type that can support multiple radios. You can also use an off-the-shelf IRLP board, should you have one laying around. The DTMF decoder is not supported by Asterisk (Asterisk uses DSP techniques to decode DTMF), so I dropped the MT8870 from my schematics. At it's simplest, all you'd really need is one NPN transistor for PTT (active high from parallel port, active low to activate PTT), and one PNP transistor for COS (if active high from radio). If your radio uses active low COS, I'd buffer with two transistors (PNP to NPN), rather than directly connecting the radio to the PC. I'd suggest using active low at the parallel port inputs. 73 and good luck. Kyle K0KN Allstar 2210-2219 --- Original Message --- Hello George, Do you have it documented anywhere how you configure the parallel port for COR and PTT? I'd love to see how you have it configured? Thanks! On Saturday, February 8, 2014, George Csahanin <george(a)dyb.com> wrote: > I bought some CM108 fobs on EBAY for $0.99 each. He has a s***load of > them. Not knowing if they'd be real CM108 I waited till I got them to send > this note. The USB ID is 08dc:000c the real thing. > > The last four nodes I built up use D945 motherboards which have parallel > ports, which I use for COS/PTT and the USB fob only does audio. No need to > modify them for PTT and COS, etc. > > Anyhow, the EBAY auction is 300503465055 OR click this > link<http://www.ebay.com/itm/300503465055?ssPageName=STRK:MEWNX:IT&_trksid=p3984…> > > Seller's store is circle607. They're in Hong Kong. But the postage was > under $1.20 for all ten. > > I stocked up simply because they work so well, cost so little, and not > sure when they will stop being available. (hoarding 101) > > GeorgeC > W2DB > Allstar 2360

3 2

Allstar parallel port (was source of USB CM108 FOBs - CHEAP)
by K&R Yoksh 09 Feb '14

09 Feb '14

http://ohnosec.org/drupal/node/177 My earlier post got line wrapped somehow 73 Kyle K0KN

1 0

Re: [App_rpt-users] audio radio to internet issue
by ea8ee 08 Feb '14

08 Feb '14

usb27305 rxboost=1 txboost=1 rxctcssrelax=1 txctcssdefault=88.5 rxctcssfreqs=88.5 ;rxctcssoverride=0 ctcssfrom=usb rxdemod=no txprelim=no txlimonly=no txtoctype=notone txmixa=composite txmixb=composite invertptt=0 duplex=0 rxondelay=o rxnoisefiltype=0 eeprom=1 The DMK works nice in TX but in RX not receive nothing 2014-02-08 20:02 GMT+00:00 Doug Crompton <doug(a)crompton.com>: > I think it found your adapter as you said you had audio in one direction. > If not see below. > > Did you select the active usb device in the config utility before you > tried to make changes? > > > If the adapter is not being found at all try this.... > > The following USB interfaces are defined in usbradio - > > #define C108_VENDOR_ID 0x0d8c > #define C108_PRODUCT_ID 0x000c > #define C108AH_PRODUCT_ID 0x013c > #define C119_PRODUCT_ID 0x0008 > #define C119A_PRODUCT_ID 0x013a > #define N1KDO_PRODUCT_ID 0x6a00 > #define C108_HID_INTERFACE 3 > > When you boot up you should see one of these initialized in the messages. > After boot do - > > dmesg | more > > and page through and see if it found your adapter. > > I am using the DMK and it looks like this - > > [root@WA3DSP_Allstar wa3dsp]# dmesg | grep Sound > input: C-Media Electronics Inc. USB PnP Sound Device as > /class/input/input0 > input,hidraw0: USB HID v1.00 Device [C-Media Electronics Inc. USB > PnP Sound Device] on usb-0000:00:1d.0-1 > > > > *73 Doug WA3DSPhttp://www.crompton.com/hamradio > <http://www.crompton.com/hamradio>* > > > ------------------------------ > From: ea8ee1(a)gmail.com > Date: Sat, 8 Feb 2014 19:14:56 +0000 > To: app_rpt-users(a)ohnosec.org > Subject: Re: [App_rpt-users] audio radio to internet issue > > > I tried with cli and radio tune rxnoise and the pc says the device > usb27305 currectly not active ! any suggestion? > > > 2014-02-08 8:51 GMT+00:00 jose <ea8ee1(a)gmail.com>: > > Hi Doug! the ptt and audio from internet to radio works nicely the > problem is about the audio from radio to internet not audio neither the > node receive the dmtf from radio or webstransceiver > > El 08/02/2014 6:31, Doug Crompton escribió: > > You need to set - > > duplex=1 ; Simplex, no telelmetry > duplex=0 ; Simplex, telelmetry > > in rpt.conf if you are running simplex. > > Also make sure the polarity is correct in your usbradio or simpleusb file > for the PTT and COS if you are using it. > > > > > _______________________________________________ App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe > from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down > to the bottom of the page. Enter your email address and press the > "Unsubscribe or edit options button" You do not need a password to > unsubscribe, you can do it via email confirmation. If you have trouble > unsubscribing, please send a message to the list detailing the problem. >

3 6

Re: [App_rpt-users] Parallel 900MHz /data radio's
by mike＠midnighteng.com 08 Feb '14

08 Feb '14

1 0

Re: [App_rpt-users] audio radio to internet issue
by ea8ee 08 Feb '14

08 Feb '14

I use URI DMK 2014-02-08 21:22 GMT+00:00 <mike(a)midnighteng.com>: > > Your FOB is stuck. > Try unplugging (live), wait 5 seconds, and plugging back in same slot. > > If it works, I suggest a new FOB. I have had a few that continuously get > stuck and replacing them worked for me so I'm not sure what the problem > is/was. > > ...mike/kb8jnm > > -------- Original Message -------- > Subject: Re: [App_rpt-users] audio radio to internet issue > From: ea8ee <ea8ee1(a)gmail.com> > Date: Sat, February 08, 2014 2:14 pm > To: app_rpt mailing list <app_rpt-users(a)ohnosec.org> > > I tried with cli and radio tune rxnoise and the pc says the device > usb27305 currectly not active ! any suggestion? > > > 2014-02-08 8:51 GMT+00:00 jose <ea8ee1(a)gmail.com>: > >> Hi Doug! the ptt and audio from internet to radio works nicely the >> problem is about the audio from radio to internet not audio neither the >> node receive the dmtf from radio or webstransceiver >> >> El 08/02/2014 6:31, Doug Crompton escribió: >> >> You need to set - >> >> duplex=1 ; Simplex, no telelmetry >> duplex=0 ; Simplex, telelmetry >> >> in rpt.conf if you are running simplex. >> >> Also make sure the polarity is correct in your usbradio or simpleusb file >> for the PTT and COS if you are using it. >> >> >> > ------------------------------ > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down > to the bottom of the page. Enter your email address and press the > "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message to > the list detailing the problem. > >

1 0