- App_rpt-users - lists.keekles.org

AllStar Echolink
by zeppelin.1＠netzero.com 22 Sep '13

22 Sep '13

Hello to all, Running two un-equal callsign and node number, AllStar in 1 P.C. How do get 2nd callsign Echolink node to operate. 73, Anton/ KC2RQR IRLP node 4012 AllStar Node 29103 Echolink 361124 ____________________________________________________________ One Weird Trick Could add $1,000s to Your Social Security Checks! See if you Qualify&#8230 http://thirdpartyoffers.netzero.net/TGL3231/523ec22f40df5422f2030st03duc

1 0

allstar sysop
by Robert N. Newberry 22 Sep '13

22 Sep '13

What is the consensus? I already have an allstar account. I see to switch your account to a sysop it is non reversible. Should I create another account for my node with my call sign N1XBM/R for sysop purposes? -- Apparare Scientior Paratus Communicare -N1XBM

2 1

Re: [App_rpt-users] Distorted audio
by Ryan Gross 21 Sep '13

21 Sep '13

Ran into this problem a while ago and was found the URI interface was the problem with similar symptoms. Is this happening in duplex or simplex with audio ? Ryan n3ssl

3 3

Fw: remote_timeout
by KJ6KO 21 Sep '13

21 Sep '13

Subject: remote_timeout In rpt.conf, is the "remote_timeout=xxx" for the RX timeout in case something on the system hangs up and will timeout after the time entered? In other words, the opposite of "totime=xxx" which is the TX timeout? Thanks... __________ Information from ESET NOD32 Antivirus, version of virus signature database 8827 (20130921) __________ The message was checked by ESET NOD32 Antivirus. http://www.eset.com

2 1

Remote base Memories
by Mark Johnston 20 Sep '13

20 Sep '13

Hello everyone, I have finally got the ic-706 remote base partially working I can scan freq, move up in freq, and read status, Now that the commands also the init=freq..... works when I connect so it can set the frequency. just fine, yet if I do *1444*000*0... etc does not work If I do *0001 for memory 001 etc, I get 'memory not found' which the memory is in the rpt.conf [memory] ;Syntax : CC=RRR.RRR,PPP.P,AAAAA ; C=Channel Number ; R=RX Frequency ; P=PL Frequency ; A=Attributes ; ;Attributes : a=AM b=LSB f=FM u=USB ; l=Low Power m=Medium Power h=High Power ; -=Minus TX Offset s=Simplex +=Plus TX Offset ; t=TX PL on r=RX PL on ; 004=147.700,123.0,fshrt 005=147.100,123.0,fshtt 006=003.860,100.0,bshrt init=003.980,100.0,bshrt ;Set to this on startup This is just above the macro section below the functions-remote... At the end of the file I tried[memory] [memory] 001=147.700,123.0,fshrt 002=147.100,123.0,fshtt 003=003.860,100.0,bshrt None of these work, always says 'memory not found' Any ideas? I know I am getting close to making this work! 0=remote,1 ; Retrieve Memory 1=remote,2 Mark KC7DMF

2 2

Telephone Portal?
by DougH 20 Sep '13

20 Sep '13

Hello, Trying to use the UK portal, enter node number and #, system says invalid selection, asks for number again then after entering once more, says there is a problem and discconnects. What am I not doing correctly? Doug - GB3KE 2253

1 0

Re: [App_rpt-users] Node 2498 is no longer in the database
by Matthew 19 Sep '13

19 Sep '13

2 1

Fwd: Jim is famous in Mexico.
by David KE6UPI 19 Sep '13

19 Sep '13

I found that Jim has a following in Mexico. He is famous there and they that put a likeness of him on the 10 Nuevos Peso. Nice going Jim. Keep up the great work.. David

3 4

Node 2498 is no longer in the database
by keith 19 Sep '13

19 Sep '13

Good evening all, I have noticed that on the (https://allstarlink.org/nodelist.php) site I show up as node 2498 in green but when I click onto the MB7IIP text I get the Node 2498 is no longer in the database. I have made no changes on my LAN and the IP of the node has been a static address since it was built. The ports on router are configured and for a short time I even set the router to DMZ the nodes address so no router interactio. My node works fine. If I reboot it does take about an hour to authenticate but once authenticated all works great. Any ideas please Kind Regards Keith Handscombe 154e886

2 1

RELAXED RADIO parms
by Keith Goobie 19 Sep '13

19 Sep '13

Good morning All. I am looking for the message that Jim WB6NIL put out there that had to do with modifying the dsp.c code so that it did not incorporate the RELAXED_RADIO parameters. One parameter is the length of time that a DTMF signal must be present before it is determined not to be a false signal. [root@Server6 main]# diff dsp.c.default dsp.c >> 165c165,166 >> < #define DTMF_TO_TOTAL_ENERGY ((digitmode & DSP_DIGITMODE_RELAXDTMF) ? >> 26.0 : 42.0) >> --- > #define DTMF_TO_TOTAL_ENERGY ((digitmode & DSP_DIGITMODE_RELAXDTMF) ? 38.0 : 42.0) /* CAH changed 26 to 38 */ This change when implemented, did eliminate a noticeable number of audio pops associated with DTMF false-ing. The message from Jim spoke to bypassing the RELAXED parameters in total. I am going through the archives and I have not found it yet. Thanks in advance. Keith -- keith(a)goobie.org Keith Goobie Richmond Hill, ON, CANADA

2 2