- App_rpt-users - lists.keekles.org

HP T5745 Thin Client
by Ron Simpson 15 Feb '13

15 Feb '13

Anyone have a start to finish ACID install documented on this unit? Any help would be appreciated! Tnx Sent from Yahoo! Mail on Android

1 0

Re: [App_rpt-users] [Bulk] Re: Simple node
by pete M 15 Feb '13

15 Feb '13

Ok, my thin client are not 5710 but 5630. Was able to transfert the limey image easily but it wont load up properly.. For those that ask how I did it. I booted a live linux cd that I had home ( scientific linux ,but I am sure almost any one would do). Got the image file on a usb stick. Used gparted to remove all partition from the flash drive. Untar, then su, then dd... As explained on the limey web page. Booted, it started loading but failed on somthing about ext2fs. It woud have been so fun to ave it run on the original flash drive.... From: petem001(a)hotmail.com To: kt9ac(a)ameritech.net Subject: Re: [App_rpt-users] [Bulk] Re: Simple node Date: Wed, 13 Feb 2013 16:32:00 -0500 I have a few 5710 at home, will try to run Limey on those, they are 1 gb ram / 1 gb flash drive.. I will have to run a live cd out of an external dvd drive to work the image on the flash drive as they are IDE 44 pin device.. If they work I will be an happy camper!! From: Tony KT9AC Sent: Wednesday, February 13, 2013 10:19 AM To: Ramesh Dhami (VA3UV) ; Benjamin L. Naber Cc: app_rpt-users(a)ohnosec.org Subject: Re: [App_rpt-users] [Bulk] Re: Simple node Myself and another ham just picked up two of the 5710 thin clients for less than $50 each shipped. So what is the recommended way to build a node - ACID with a larger drive or Limey with existing hardware inside (512M ram/ 512M flash)? I like simple_usb because using a repeater or S-COM interface all you need is audio and logic signals. I would like a few GPIO outputs for external control purposes, too. What is the K0KN PLRI interface? Does that take advantage of the parallel port or something? Thanks, Tony --- On Tue, 2/12/13, Benjamin L. Naber <Benjamin(a)kb9lfz.com> wrote: From: Benjamin L. Naber <Benjamin(a)kb9lfz.com> Subject: Re: [App_rpt-users] [Bulk] Re: Simple node To: "Ramesh Dhami (VA3UV)" <Ramesh(a)va3uv.com> Cc: app_rpt-users(a)ohnosec.org Date: Tuesday, February 12, 2013, 6:38 PM You may be able to get away with not buying a micro-drive which will fail sooner than later. Use Limey Linux. I have a Neoware which was bought out by HP. Neoware and HP thin clients have VIA chipsets in there, ie microprocessor, ethernet controller, audio, and Super i/o which controls your serial, parallel ports among other things. I used the K0KN PLRI interface that I was able to build from parts in my junk box. After a little solder smoke filled the air, made a few adjustments, the URI was working for the TX. I use the inexpensive StarTech USB sound FOB for TX/RX audio, and have the settings set to DSP to detech RX audio and CTCSS tone. After it was setup with a service monitor, it works wonderful. Zero issues. Now I just need to build, test, and install a better, higher, antenna. ~Benjamin, KB9LFZ Allstar node 28569 On Mon, 2013-02-11 at 20:48 -0500, Ramesh Dhami (VA3UV) wrote: > On 11/02/2013 8:04 PM, Alan Adamson wrote: > > All, I think I know the answer to this, but figured I'd check again… Yes > > I know I could do an RTCM (I have 5 of them already). I'm looking to > > get another family member (new ham) up with a personal node. Was hoping > > that someone might have done something around the Beagle Bone as the Pi > > seems to no be up for the task. I could live with simpleusb if needed. > > > > Are there any *inexpensive* options to get to a functional simpleusb > > type node?If so, what are they? > > > > <-- Hi Alan; Best candidate (IMO) is a HP Thin Client - something like > the HP T5710; you can pick them up off eBay for as little as $25US (you > have to look out for them!) - then there is a mod' to remove the memory > module and install a 4GB micro-drive. You can install ACID right off an > external (USB) CD. > > The HP will run chan_simpleusb just fine. > > Low cost / works great / low power (runs off 12V / 13.8VDC @ ~ 650mA). > > Cheers! > > Ramesh. > > _______________________________________________ > App_rpt-users mailing list > wlmailhtml:/mc/compose?to=App_rpt-users@ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users _______________________________________________ App_rpt-users mailing list wlmailhtml:/mc/compose?to=App_rpt-users@ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

1 0

Ok, so what happened to this site?
by Alan Adamson 14 Feb '13

14 Feb '13

http://picklejar.org/ Doesn't even resolve to anything anymore. Is the site sill there with another address? Alan

1 0

Node Proxy Setup
by Chris Andrist 14 Feb '13

14 Feb '13

I am trying to setup a node at my office, the only problem is that they will not open the ports for me to use a app_rpt node. In reading it seems that I can proxy all of my connections through another computer. I am wondering if I can use my primary node/hub as the proxy? If so, does anybody have some sample config that I can use? In addition, my company blocks a lot of outgoing ports so I may have to use non-standard ports. I know the standard IAX port is blocked. Regards, Chris Andrist, KC7WSU Allstar Nodes 29205-29214

1 0

Node 2519
by Orland Lopez 14 Feb '13

14 Feb '13

Good Day fellas, I am looking to get back into the allstar swing after a few years away from the scene. I hope the node 2519 was grandfathered as I have not used it for a while. I just bought a URI and will try to my Handy Dandy HP T5720 Thinclient up and running. Limey linux should be no issues. I logged into the allstarlink site and noticed a lot good changes. Question is, if node 2519 can be used will I be able to use this node in the limeylinux, I ask because back then when I got the node number Limey was non existant. Thanks -- Gracias y 73's Hasta la Vista KI6LNX YN1OB

1 0

Re: [App_rpt-users] thanks
by K&R Yoksh 13 Feb '13

13 Feb '13

Hi David, I hadn't really considered that.. I periodically tar up my /etc/asterisk and a few other directories and back them up.. That way, if my hard drive were to crash, etc, I can easily restore my system after installing ACID. I run the upgrade.sh probably every few months, if I happen to notice there's been an SVN update. Feel free to edit as needed, though (as I did!), I'm not sure who wrote the initial script.. Duuude perhaps? 73, Kyle K0KN --- Original Message --- Hello Kyle, I like your update script. Had thought about adding a backup line to your script?cd /etc/zip -r asterisk.zip asteriskDavid

1 0

Hunt group?
by K&R Yoksh 13 Feb '13

13 Feb '13

Hi, I've got a question for the dialplan experts. Is it possible to create a "hunt group" of sorts? In other words, I'd like to know if it's possible to edit the dialplan to connect to node #1 if available, or if not, try connecting to node #2, etc. I'd like to use this to allow users to dial the same node number each time, but be connected to one of two hub nodes in the event of ISP problems, etc. Thanks. 73 Kyle K0KN

1 0

thanks
by Bryan D. Boyle 13 Feb '13

13 Feb '13

Thanks for the work! That got rid of a lot of false DTMF detection on my systems....and I guess, forced me to update to the current distro at the same time (something I've been meaning to do, but just haven't found or had the time to do since I've started a new job...the run time on the system, according to allmon was over 3K hours...) BB > From: "K&R Yoksh" <yokshs(a)gmail.com> > Date: February 13, 2013, 0:29:54 EST > To: "app_rpt" <app_rpt-users(a)ohnosec.org> > Subject: [App_rpt-users] Automatically remove RADIO_RELAX > > If anyone is interested, I've added a line to the "upgrade.sh" file, to automatically remove the RADIO_RELAX parameter when upgrading your Asterisk to the latest SVN release. > > My system experiences quite a bit of DTMF false decodes with the RADIO_RELAX parameter in place, and it's easy to forget that step when recompiling. > > wget http://www.qsl.net/k0kn/upgrade.sh > > 73 > > Kyle Yoksh > K0KN > Olathe, KS -- Bryan In this world, you must be oh so smart or oh so pleasant. Well, for years I was smart. I recommend pleasant. You may quote me. Sent from my MacBook Pro.

2 2

Q: Beagle Board and URI
by torben＠klimt-online.com 13 Feb '13

13 Feb '13

Hi all, ist it necessary to buy the lox board for the beagle board xM or can i still use my URI instead of it ? Are there any other low power boards possible ( i know Raspberry Pi is no option ;-) Greeetings from Germany Torben DH6MBT Torben Klimt Eicherstrasse 58 85123 Karlskron-Grillheim Telefon: 08453-34 45 040 Mobil: 0151-178 74499 torben(a)klimt-online.com<mailto:torben@klimt-online.com>

2 1

Automatically remove RADIO_RELAX
by K&R Yoksh 13 Feb '13

13 Feb '13

If anyone is interested, I've added a line to the "upgrade.sh" file, to automatically remove the RADIO_RELAX parameter when upgrading your Asterisk to the latest SVN release. My system experiences quite a bit of DTMF false decodes with the RADIO_RELAX parameter in place, and it's easy to forget that step when recompiling. wget http://www.qsl.net/k0kn/upgrade.sh 73 Kyle Yoksh K0KN Olathe, KS

1 0