- App_rpt-users - lists.keekles.org

Freq Agile 220 MHz radio
by Scott Weis 21 May '10

21 May '10

Anyone have any ideas for a 220MHz radio for a frequency agile remote base? Has anyone got the serial control info for the DR-235 from Alinco? Thanks, Scott KB2EAR

2 1

A couple of questions....
by Chuck Kraly 15 May '10

15 May '10

I know I have seen this question before, but I cannot find it in the archives. Is there a way to turn off all the connect/disconnect messages? Just leaving the double beep would be enough for our network. Also, has anyone done any recording (produce a wav or mp3 file ) of the traffic through a node? We have a slight problem here on one of our nodes, and I would like to have an audio file to hand to the FCC. Thanks, Chuck K0XM

2 1

Parrot mode
by Chuck Kraly 15 May '10

15 May '10

Well, after realizing I had some major "cranial flatulence", I got Parrot running on 2180/2181. Thanks for the help and suggestions via direct email. Now, to find our jammer on 2180..... Chuck K0XM

1 0

Have to manually crank the usb fob to make it work?
by Steve Gladden 14 May '10

14 May '10

Just did a clean install of ACID on a Compaq DL380 server This is a Box with Dual Pentium 733's and no built on USB. Also to make this more fun I'm using a USB PCI card to get USB support. The card has an NEC chipset and I can provide more details as wanted. It reliably does not work on bootup. What I mean by that the USB FOB is not producing any audio on it's output.. It has the normal flashing light on the fob and the software behaves like usual when sending audio (no errors) or anything on screen that looks out of ordinary.. Now if I manually do an: rpt restart and then radio key and radio unkey a few times it startes to work and then works just fine after that.. If I restart asterisk or the entire box the problem comes back. Has anyone else ever experienced this or soething like it? I will try another USB card and moving the card around to different interrups.. Just weird... and that it works after slapping it around with commands... Michigan Broadband Systems Inc. "Always Connected" (734)527-7150 Steve's cellphone: (734)904-1811 -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.

3 3

Parrot Mode
by Chuck Kraly 14 May '10

14 May '10

Is anyone using this option? If so, I ahve a few questions on the setup. Contact me off list if you would Chuck K0XM ckraly(a)gmail.com

1 0

SIP phones
by Chuck Kraly 13 May '10

13 May '10

Which model of SIP phones is everyone using? Any preferences? Chuck K0XM

10 10

Re: [App_rpt-users] Can you connect to a node just on the lan? (multihome? how?)
by Steve Gladden 12 May '10

12 May '10

> On Sat, 8 May 2010, Steve Gladden wrote: > >> I've got two nodes: >> >> 2586 and 27036 >> >> Both sit on the same LAN. >> >> Is it possible to connect one to the other (link) them >> over the LAN while they are still reachable from the >> Internet via ALLSTAR public node list >> >> You can see my attempt below that is failing across the LAN. >> I don't know if it is failing because the same node number >> is also in the public IP/ public nodelist. >> >> Is there a way to 'locally' override the public node list >> so it's number is reachable 'locally' via lan or VPN? >> >> Or do local type nodes need to not also register with ALLSTAR LINK? >> >> In this example I'm trying to make outbound link to node >> 2586 which is at 10.73.73.9 internally.. >> >> Back on node 27036 in it's config I of course am pointing >> back to 2586 at it's internal IP (not shown here). >> Thanks! -Steve >> >> >> 27036 = radio(a)127.0.0.1/27036,NONE ; This must be changed to your >> node number >> >> 2586 = radio(a)10.73.73.9/2586,NONE >> >> >> >> >> >> >> >> Michigan Broadband Systems Inc. >> "Always Connected" >> >> (734)527-7150 >> >> Steve's cellphone: (734)904-1811 >> >> >> > BUMP: Please & Thank You.. > > I'd like to link my two nodes over the local network and have almost > got it but not quite... > Am I missing a step or concept here? > > Can I multihome an Internet registered node locally? as you see me > attempting above? > > Or can a node have two simultaneous identities? one for the LAN > and another for registering with Allstar Link? > > -Steve Anyone ever done this? I'm trying to get it working for Dayton if possible. -Steve -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.

3 3

Re: [App_rpt-users] Noise Problem with URI and Voter Comment
by hwstar＠rodgers.sdcoxmail.com 11 May '10

11 May '10

> > From: MICHAEL SMITH <kb8wlw(a)me.com> > Date: 2010/05/04 Tue AM 10:12:47 PDT > To: app_rpt-users(a)qrvc.com > Subject: [App_rpt-users] Noise Problem with URI and Voter Comment > > Sorry guys I just realized when I was hitting reply, I was replying directly to the individual. I would guess proper etiquette would be to email the group. Or at least CC the group. > > Thanks for all of the suggestions, I will try adding in a resistor or a voltage divider. I will have to check to see if I have a 1:1 transformer laying around. And yes the "RADIO TUNE TXVOICE" was on the far low side. I will also double check to see if the monitor is creating the noise by turning it off. > > I thought the same thing (regarding local HT noise) and hooked up the audio input leads to the audio path and seen this (hopefully I can attach a picture). I also had someone off site confirm they heard the noise. I did not think about trying to figure out the frequency. > > Looks like coherent noise from the 1ms interrupts Asterisk uses. Probably sounds like a raspy 1kHz tone. Try the voltage divider first. Your scope picture shows 10mV of noise (assuming a x1 probe ad 2mV/div). I'd try a 20:1 voltage divider ratio. BTW: The 1:1 transformer will not help as the ground from the URI still needs to be connected to the radio for proper operation of the control signals COR and PTT and the isolation action of the 1:1 xfmr will be defeated. Another approach would be to drive the TX modulator directly and not use the mic input. Steve WA6ZFT The asterisk computer is powered by a local AC outlet and the DC supply shares the same AC circuit. The AC and DC grounds are bonded. The DC supply also floats about 650 amp hours of battery back up. Even with all the batteries, I never had any luck using a inverter or a UPS tied to the DC buss. I thought it would be nice to power the windows based echo link computer from a computer grade UPS (or inverter) that uses the main DC supply with the batteries. But it introduces to much noise into the system that seems to only shows up on the UHF machines. So I have to have battery back up for the PC's separate of the system. Has anyone ever tried a "Car Computer" case that is designed to run off of 12 volts DC? I should have some time Wednesday night to try all of the suggestions, Thanks again. I will keep everyone posted. 73's Mike / KB8WLW 145.410 MHz PL 110.9 224.480 MHz PL 141.3 442.225 MHz PL 131.8 442.450 MHz PL 131.8 927.6125 MHz PL 131.8 Echo Link Node # 146520 This is a KB8RST Sponsored System www.kb8wlw.com kb8wlw(a)me.com _______________________________________________ App_rpt-users mailing list App_rpt-users(a)qrvc.com http://qrvc.com/mailman/listinfo/app_rpt-users

2 1

Will anyone be at Dayton with a portable Allstar node?
by Bob Brown - WØNQX 10 May '10

10 May '10

Hi All Will anyone be at Dayton with a portable Allstar node? if so, what freq and node # -- Thanks in Advance Bob Brown, WØNQX Kansas City Metro Area http://sm0kenet.net http://byrg.net http://kcdstar.byrg.net Quis custodiet ipsos custodes?

3 2

Can you connect to a node just on the lan? (multihome? how?)
by Steve Gladden 08 May '10

08 May '10

I've got two nodes: 2586 and 27036 Both sit on the same LAN. Is it possible to connect one to the other (link) them over the LAN while they are still reachable from the Internet via ALLSTAR public node list You can see my attempt below that is failing across the LAN. I don't know if it is failing because the same node number is also in the public IP/ public nodelist. Is there a way to 'locally' override the public node list so it's number is reachable 'locally' via lan or VPN? Or do local type nodes need to not also register with ALLSTAR LINK? In this example I'm trying to make outbound link to node 2586 which is at 10.73.73.9 internally.. Back on node 27036 in it's config I of course am pointing back to 2586 at it's internal IP (not shown here). Thanks! -Steve 27036 = radio(a)127.0.0.1/27036,NONE ; This must be changed to your node number 2586 = radio(a)10.73.73.9/2586,NONE Michigan Broadband Systems Inc. "Always Connected" (734)527-7150 Steve's cellphone: (734)904-1811 -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.

1 0