November 2010 - App_rpt-users - lists.keekles.org

CLI Message question
by Randy 26 Nov '10

26 Nov '10

I keep getting a --Hungup "Zap/pseudo-701421791 String on my CLI screen..What is this telling me. It,s not connected any where Randy

2 1

cant connect locally
by Randy Ballard 25 Nov '10

25 Nov '10

Does anyone have an idea what would cause this rpt fun 27469 *327386 -- Hungup 'Zap/pseudo-1125564719' [Nov 25 12:55:17] NOTICE[2809]: chan_iax2.c:4071 __auto_congest: Auto-congesting call due to slow response -- Hungup 'IAX2/127.0.0.1:4569-1577' cant connect to another node on the same server they are defined in the rpt file 27386 = radio(a)127.0.0.1/27386,NONE 27387 = radio(a)127.0.0.1/27387,NONE 27385 = radio(a)127.0.0.1/27385,NONE 27469 = radio(a)127.0.0.1/27469,NONE am able to connect to a node on another server just not itsself -- Randy Ballard KB3HJC <http://kb3hjc.net>

2 1

Two Radios, one URI...
by Peter Elke 25 Nov '10

25 Nov '10

Hi All, After surveying all of the repeater sites, two of them are not good locations for direct internet access. The WISP is too slow or has way too much jitter. As a plan B will be attempting a 420mhz full duplex backhaul link to an IP connected node. On those "bad" sites we will be using app_rpt in a standalone mode as a local repeater controller. Here is my cost saving question... Using one URI is there a way to use the right channel for node A (main repeater) and the left channel for node B (backhaul 420 link)? I can use a parallel port as needed for I/O if that is an issue... Pete

2 2

mini pci WiFi card?
by Peter Elke 25 Nov '10

25 Nov '10

Hello All, For the pelican box server/node I am now shopping for a 802.11b/g mini pci wifi card. Any recommendations on ones that work well with ASID CD? Pete

5 6

no receive audio in sofphone or iaxRpt
by Eva Pareja 25 Nov '10

25 Nov '10

Hello, I am getting in contact with RoIP. We are using the ACID install with DMK URI to connect a half duplex radio without COR line. So we have connected PTT (pin1), GND (pin20) , MIC_AC(pin 21) and LEFT_AC (pin 22). We have also installed the iaxrpt client and the voice is received in a remote radio perfectly. But we have the problem in the way back. If you speak from the remote radio, the voice signal arrived at the LEFT_AC of URI but if it is not processing. Nothing is listened in the iaxrpt client. I had tried to comments the txctssdefault,rxctcssfreqs and txctcssfreqs because i have introduced ctcssfrom=no and also i invert the txmixa and txmixb settings but it didn´t work. The usbradio.conf looks like this: ; ; Usbradio channel driver Configuration File ; [general] [usb] hdwtype=0 ; Leave this set to 0 for USB sound fobs modified using ; the instructions from usbfob.pdf. Use a setting of ; 1 is for Dingotel/Sph interfaces. rxboost=0 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed ; Set to 1 for additonal gain if using a low-level receiver output rxctcssrelax=1 ; reduce talkoff from radios w/o CTCSS Tx HPF ; Do not change this, leave this as a 1 ;txctcssdefault=100.0 ; default tx ctcss freq, any frequency permitted ;rxctcssfreqs=100.0 ; rx ctcss freqs in floating point. must be in table ;txctcssfreqs=100.0 ; tx ctcss freqs, any frequency permitted ;rxctcssoverride=0 ; Set to 1 or yes to start out in carrier squelch mode carrierfrom=vox ; no,usb,usbinvert,dsp,vox ; no - no carrier detection at all ; usb - from the COR line on the modified USB sound fob ; usbinvert - from the inverted COR line on the modified USB sound fob ; dsp - from RX noise using dsp techniques ; vox - voice activated from RX audio ctcssfrom=no ; no,usb,dsp ; no - CTCSS decoding, system will be carrier squelch ; usb - CTCSS decoding using input from USB FOB ; (currently not supported) ; dsp - CTCSS decoding using RX audio in DSP. ; rxdemod option must be set to flat for this to work. rxdemod=speaker ; input type from radio: no,speaker,flat ; no - RX audio input not used ; flat - Use RX audio from discriminator (before de-emphasis) ; speaker - use de-emphasized audio txprelim=no ; Audio processing on left output channel: no,yes ; no - Audio is not pre-emphasized and limited. ; Suitable for use on a microphone input ; yes - Audio is pre-emphasized and limited. ; Suitable for direct connection to an FM modulator txlimonly=yes ; Audio limiting with no pre-emphasis on output channel: no,yes ; no - Audio is not limited. ; yes - Audio is limited. ; Suitable for transmitters with no limiting but with pre-emphasis. ;txtoctype=notone ; Transmit tone control type: no,phase,notone ; no - CTCSS tone encoding with no hang time ; phase - encode CTCSS and reverse phase ; AKA ("reverse burst") before unkeying TX ; notone - encode CTCSS and stop sending tone before unkeying TX ; AKA ("chicken burst") txmixa=no ; Left channel output: no,voice,tone,composite,auxvoice ; no - Do not output anything ; voice - output voice only ; tone - CTCSS tone only ; composite - voice and tone ; auxvoice - auxiliary voice output at headphone level for monitoring txmixb=voice ; Right channel output: no,voice,tone,composite, auxvoice ; See txmixa above. invertptt=0 ; Invert PTT 0 = ground to transmit, 1 = open to transmit ; This is the collector lead of the 2n4401 on the modified ; usb sound fob. ; please refer to the howto for the procedure to do this. duplex=0 ; Half Duplex rxondelay=20 ; Uncomment and/or adjust for simplex nodes to eliminate "Ping Ponging" ; or "Relay Racing". ; A positive value here will instruct the usbradio driver to ignore the ; COR line for a specified number of 20mSec intervals following the ; release of PTT. Use this only on simplex nodes, and leave commented ; out for repeaters or other full duplex nodes. Can anyone help me and tell me what i am doing wrong? Thank you. Regards, Eva

2 1

Extra URI for sale..
by James Nessen 25 Nov '10

25 Nov '10

I have an extra URI for sale. Asking 75.00 shipped. It was purchased for another ham who wanted a node, but then lost interest. It's in 100% working condition and comes with it's USB cable. Please email off list, first one gets it! Jim, K6JWN Node 2142

2 2

Re: [App_rpt-users] mini pci WiFi card?
by Philip Dorr 23 Nov '10

23 Nov '10

Most atheros based cards should work, but I have not run ASID with a wireless card. If you need a long range card you could look at Ubiquiti cards. On Nov 22, 2010 2:46 PM, "Peter Elke" <pete.elke(a)esquared.com> wrote:

1 0

TheLinkBox connectivity
by Jim Duuuude 23 Nov '10

23 Nov '10

App_rpt is now able to interface directly with TheLinkBox. See: http://app-rpt.qrvc.com/node/178 JIM WB6NIL

4 3

Test
by Stephen Rodgers 21 Nov '10

21 Nov '10

This is a test

1 0

Remote timeout message
by Tony KT9AC 20 Nov '10

20 Nov '10

Trying to find out which variable to change...have two nodes on a server, one repeater full-duplex, the other a remote base half-duplex (RF link). When I connect them together after a short period of being active I hear "remote timeout" and the system drops. I am then able to kerchunk and everything starts working again. If the remote is connected and idle, there is no timeout. A guess is probably 20-30 minutes before it happens. Here is what I have defined: [repeater] ;lnkactenable=0 ; Set to 1 to enable the link activity timer. Applicable to standard nodes only. ;lnkacttime=1800 ; Link activity timer time in seconds. ;lnkactmacro=*52 ; Function to execute when link activity timer expires. ;lnkacttimerwarn=30seconds ; Message to play when the link activity timer has 30 seconds left. ;remote_inact_timeout=1800 ; Inactivity timer for remote base nodes only (set to 0 to disable). ;remote_timeout=3600 ; Session time out for remote base. (set to 0 to disable) [remote] remote_inact_timeout=0 ; Inactivity timer for remote base nodes only (set to 0 to disable). remote_timeout=0 ; Session time out for remote base. (set to 0 to disable) --other settings like above removed-- Am I reading the docs wrong where the remote has its timeouts set to zero, should I include all options above and set to zero also? For these activity timers, is the local or remote end that applies? Sorry I don't have more info or can readily try changes, my DSL isn't installed at the site yet, so its standalone for a while. I'll be stopping by to make a few changes and want to get this right. Thanks, Tony

1 0