December 2011 - App_rpt-users - lists.keekles.org

AllStar Link Portal signon problems
by Fran 08 Dec '11

08 Dec '11

Hello, I have 2 ham friends who have requested passwords via the AllStar Link Portal sever days ago and then also resent their request and are still waiting, is it possible that the automated server that handles request is malfunching?

2 1

Low Band Remote Base
by Monty 08 Dec '11

08 Dec '11

Hello Everyone, I have successfully integrated a Low Band Syntor X with an Xcat to app_rpt using CI-V. I have a problem though. There are currently 6 6m repeaters here in Arizona, 3 have 0.5 mhz split and the other 3 have 1 mhz splits. I have only been successful in programing the 0.5 split frequencies in App_Rpt memories. Is there a trick to make it split to 1 mhz or is that not possible? Monty

3 3

Some help
by Fran 08 Dec '11

08 Dec '11

Hello, I am building a node useing the ACID install disk, my hardware is the DMK USB interface connected to a cable from URI terminating into a DB9 connected to port 3 on an Arcom rc210 controller. This Node will be directly connected to my repeater via port 3 on the RC210. I also will be building a simplex node at another location, these are my variables, can anyone tell me what files I need to modify on my node pc to get this up and running? Also what files need to be modified on the simplex node? Thanks KB2AYS Frank

1 0

Port forwarding node 28177
by Jwbfre＠aol.com 07 Dec '11

07 Dec '11

Cannot receive incoming connections on node 28177. Using Belkin router with port forwarding set to send port 4569 to a static ip of 192.168.2.3 udp Can ping google .com ok and all the other pc's on the lan. Would you check my node in the registration server. Thanks Jack Bumgarner ws5d

3 2

Re: [App_rpt-users] Solid State Drive
by Ed 07 Dec '11

07 Dec '11

I use an IDE to CF adaptor, with a 4GB CF card. I tried a 2GB, but that was not large enough for the build, lots of errors. I have been running this my box for the local club for over a year without any problems. Less moving parts also. This method is cheaper than the SSD drives on the market, about $30 is what I spent. Ed KI6PSP Sent from my iPad

4 4

URI 6dB amp for Kenwood TM271a ?
by KC2WDZ 07 Dec '11

07 Dec '11

Has anyone had to use the 12v / 6dB amp of the URI with the modified Kenwood TM-271a radio? I did the 6 pin mini din data mod on the tm271a radio and was under the impression the 6dB amp would be needed. But I seem to be getting the audio from the 9600 baud pin just fine.

1 0

Solid State Drive
by Jim W7RY 07 Dec '11

07 Dec '11

Anyone using a solid state drive for their node? If so, what type. How is it working out? I'll need a 3.5 inch for a rack mount server. Thanks! 73 Jim W7RY

3 3

Two remote nodes used to link two repeaters
by Ron Morell 07 Dec '11

07 Dec '11

Hello, I'm new to Asterisk+app_rpt. Will this application connect two transceivers (remote nodes) using VoIP so that each transceiver node will transmit what it receives over the VoIP input from the RF receiving transceiver node? If it will, I'd appreciate some discussion as to how to setup this type of connection or direction to directions, if already written. I've been back reading the archives and have read most of this year's discussions. Lots of good info on this reflector. Thanks for your consideration. Ron Morell KA7U

4 5

Re: [App_rpt-users] Two remote nodes used to link two repeaters
by Robert A. Poff WB3AWJ 07 Dec '11

07 Dec '11

Perhaps I reacted to rashly.... Is the real question these fellows are asking "How does this work? And how do I make it work?" My answer: Start by reading the very good overview on the Allstar Link site. In particular the ABOUT page. And the GET STARTED page. Once you grasp the concept, come on back here where you'll find lots of people to answer the rest of the questions. Once you get the node(s) running, you can do exactly what you are proposing. With two repeaters, twenty repeaters, thirty repeaters........... Robert A. Poff Loganville, PA. W3SBA Repeater - Allstar 27784 "Lieutenant, target the offending power boat and launch photon torpedoes" ----- Original Message ----- From: "DougH" <specialq.que(a)ntlworld.com> To: "Robert A. Poff WB3AWJ" <wb3awj(a)comcast.net> Sent: Tuesday, December 6, 2011 4:09:05 PM Subject: Re: [App_rpt-users] Two remote nodes used to link two repeaters Exactly and a whole lot more...your system into others world wide. D

4 3

DC Powered PC
by Tony KT9AC 06 Dec '11

06 Dec '11

Just asking for those that are running a regular Pentium 4 style PC at their repeater sites, have you left it running the stock ATX power supply or converted to a 12V DC-DC style attaching to the repeater's power supply? The HP D510S that I use is rated for 50W, so I'm looking at a $30 DC-DC converter without rebuilding the entire thing as an Atom in a rack mount. Thanks! Tony

1 0