- App_rpt-users - lists.keekles.org

Nodes not registering
by Matthew Pitts 16 Dec '12

16 Dec '12

Hello folks, I've done some configuring of my nodes, and I'm having trouble getting the two I'm currently running to register. The nodes in question are 28713 and 28910. I have set the proper port in my router, but it's not seeming to work at the moment. Matthew Pitts N8OHU

1 0

Help Needed With Fatal Error
by Chris K7AZ 13 Dec '12

13 Dec '12

What should I do when I get a fatal error ³Could not modify asterisk config file² Thank you, Chris K7AZ

1 0

More Newbie questions
by Dave Miller 12 Dec '12

12 Dec '12

Reading over the documentation it's still unclear if I can run Limey Linux download from Allstar link download page on a IntelD525 motherboard? And what steps do I need to follow? Do I need a running Linux system or can I use an OSX machine to unpack the download from Allstar link page onto a USB drive or a memory card then put the card into the D525 motherboard? I am about to grab some hardware and jump in but not sure yet what I need to grab. Many thanks Dave VE7PKE Sent from my iPad

3 2

Re: [App_rpt-users] App_rpt-users Digest, Vol 46, Issue 20
by Bob - AF6D 12 Dec '12

12 Dec '12

I am completely new to Allstar and hope that you will excuse what some will think is a stupid question. We have three repeaters on the same pair that we wish to link together in a voted simulcast configuration. I inquired about using our existing RC-210 controllers and was asked why I wanted to use a controller when Allstar can do such a great job. I am sure it can but I am curious how we get our phone patch and our weather receivers integrated, as well as RF links. As an ECOM repeater service these are important to us. Simple is of course better but like I said I am completely green. I read that there is a piggy back device that allows the repeater to share a controller with a RTCM -- is that still an option? Thank you in advance. -----Original Message----- From: app_rpt-users-bounces(a)ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of app_rpt-users-request(a)ohnosec.org Sent: Wednesday, December 12, 2012 9:00 AM To: app_rpt-users(a)ohnosec.org Subject: App_rpt-users Digest, Vol 46, Issue 20 Send App_rpt-users mailing list submissions to app_rpt-users(a)ohnosec.org To subscribe or unsubscribe via the World Wide Web, visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users or, via email, send a message with subject or body 'help' to app_rpt-users-request(a)ohnosec.org You can reach the person managing the list at app_rpt-users-owner(a)ohnosec.org When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..." Today's Topics: 1. Re: More Newbie questions (Ken) ---------------------------------------------------------------------- Message: 1 Date: Wed, 12 Dec 2012 05:16:12 -0500 From: "Ken" <ke2n(a)cs.com> To: "'Dave Miller'" <ve7pke(a)gmail.com> Cc: App_rpt-users(a)ohnosec.org Subject: Re: [App_rpt-users] More Newbie questions Message-ID: <003b01cdd851$b7338550$259a8ff0$(a)cs.com> Content-Type: text/plain; charset="us-ascii" Curious why you want Limey Linux - I run a standard install on the D525 (and D510) without problems. 73 Ken > -----Original Message----- > From: app_rpt-users-bounces(a)ohnosec.org [mailto:app_rpt-users- > bounces(a)ohnosec.org] On Behalf Of Dave Miller > Sent: Wednesday, December 12, 2012 2:55 AM > To: App_rpt-users(a)ohnosec.org > Subject: [App_rpt-users] More Newbie questions > > Reading over the documentation it's still unclear if I can run Limey Linux > download from Allstar link download page on a IntelD525 motherboard? And > what steps do I need to follow? Do I need a running Linux system or can I use > an OSX machine to unpack the download from Allstar link page onto a USB > drive or a memory card then put the card into the D525 motherboard? I am > about to grab some hardware and jump in but not sure yet what I need to > grab. > > Many thanks > Dave > VE7PKE > > Sent from my iPad > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users ------------------------------ _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users End of App_rpt-users Digest, Vol 46, Issue 20 *********************************************

2 1

Autopatch capability
by Michael Hebert 12 Dec '12

12 Dec '12

Greetings! Is the autopatch capability still available for $5 a month? After I subscribe, will I get an email on how to set it up? Thanks, Mike KD5DFB

3 3

IAXRPT on MAX OSX Mountain Lion using Winebottler
by Dave Miller 11 Dec '12

11 Dec '12

I have been unsuccessful in my attempts to get IAXRPT running on my Mac. I can get it to launch but when I try to setup the audio devices the usual suspects are not there. Just blank drop down menus. I can use the Web tranceiver on Allstar to connect to nodes, but would like to get a standalone app running. If there is a better option that I can run native in OSX I am pleased to try that. When I was chatting tonight to VA3VD and VA3MPG they mentioned this might be a known issue but did not have an immediate solution. Once I get the audio devices running then next step is figure out how to set up an account so I can access the public nodes. I can be pretty dense most days and have not seen any documentation about how to get it accessing the public nodes on Allstar or are those only accessible through the web transceiver. I will get my own node up soon as Ramesh releases the RPI code. ;-) Thanks Dave

4 5

Re: [App_rpt-users] Allmon
by ki6ies.tasma＠gmail.com 10 Dec '12

10 Dec '12

Thanks for the reply. Also is there a easy way to add a Group2 to the menu bar to have a separate grouping of nodes. I tried adding [Group2] and the node numbers I wanted. But no go. Ian Ki6ies

1 0

Update on the Pi
by Ramesh Dhami (VA3UV) 09 Dec '12

09 Dec '12

OK Guys; Sorry about the IP address change! - I was deliberately keeping the Pi 'dynamic' with the intent of imaging it when we are ready. Having said that, I have set a static IP address - node 29109 can now be accessed directly... I have limited cycles, so I'm not always monitoring. A couple of you were able to connect yesterday (before the darn IP changed!) - the lucky few were able to listen to my audio.... it is not perfect - especially the received audio (i.e., audio into the network). However, the intent of the demo yesterday was to demonstrate that this is an active project (not vapor-ware!)... we do have a Pi operational - with issues - it is as they say, "Work In Progress" Initially, the TX audio (i.e., audio out of the local transmitter) was also raspy - use of an externally powered USB hub cleared up the TX audio. Unfortunately, the hub had little to no affect on the RX audio. We (mostly Jim, and me to a lesser extent) are working on it.... but we are both busy - and 'tis the season to be busy! We are not ready to publish / post an image just yet.... some of you know me from my FREE STAR* project, nothing leaves my "lab" until I have fully tested and documented it. It's that simple; right now, we are in development and testing. We realize that there is huge interest in the Pi at the moment - I do support the Pi with an image, installation script and documentation for my FREE STAR* project (http://www.va3uv.com/iso.htm) When we are ready and feel that the product is ready for field testing, we will gladly make it available in a similar fashion. Cheers for now! Ramesh. www.freestar.us

1 0

Navigating Linux & AllStar Sign-In
by Chris K7AZ 09 Dec '12

09 Dec '12

Can anyone help me with Linux commands to allow viewing the file called /root/acid-install.log? I also need help with AllStar sign-in process. The system will no longer allow me to sign in and the reset password does not work. Thanks, Chris K7AZ

6 6

Allmon
by Ian Venable 09 Dec '12

09 Dec '12

Quick question. When you have multiple servers reporting back to your Allmon server can they all use the same port defined in the manager.conf file, or does each server need to talk back on there own port? Ian Ki6ies

1 0