- App_rpt-users - lists.keekles.org

AWS hosted ASL install?
by Russell Thomas 18 May '18

18 May '18

I was interested in installing a cloud version of ASL to see if I could setup a DVSwitch project. I have a linux virtual server running linux. I went by the following instructions: https://wiki.allstarlink.org/wiki/ASL_FAQ but i'm getting messages and i'm not sure how to correct it? 73, Russell Thomas, KV4S Cell: 205.202.1701 DMR: 3101393 D-Star: KV4S AllStar: 47923 EchoLink: KV4S-L HamShackHotline: 4225 Web: http://KV4S.com

5 11

CM108B
by Skyler F 17 May '18

17 May '18

All of the newer fobs from Amazon are shipping with CM108B. I ordered some of these cards as shown in the links below, and it looks like they all have the CM108B. https://www.amazon.com/Sabrent-Aluminum-External- Adapter-AU-EMCB/dp/B00XM883BK/ref=sr_1_2?ie=UTF8&qid= 1522680132&sr=8-2&keywords=cm108 https://www.amazon.com/KNACRO-Free-driver-sound-CM108/dp/ B01F4LNXUI/ref=sr_1_1?ie=UTF8&qid=1522680368&sr=8-1&keywords=cm108 I'm not around my nodes yet to test the fobs if they work, but I thought I remember the CM108B not being supported last time I checked 4 months ago. (except for our favorite people at hamvoip). Does ASL support this? It is getting harder to find fobs that do not have CM108B skyler

4 5

stats post and private nodes
by Bryan Fields 17 May '18

17 May '18

I'd like to ask if you're running a private node, please disable the stats post program for that node. It's just going to waste time on the stats server, and we're seeing about 50 hits per second from private nodes in the 1... range. Thanks, -- Bryan Fields 727-409-1194 - Voice http://bryanfields.net

1 0

Re: [App_rpt-users] Node Type
by Mike Besemer 16 May '18

16 May '18

Thanks for bringing that up Joe and Steve. I've already got a few Moto radios set up for Echolink... I'll be using one of them. I think I'm taking audio off the top of the squelch pot, so it should be discriminator audio, but you've reminded me to check that. 73, Mike WM4B -----Original Message----- From: App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] On Behalf Of Steve Zingman Sent: Wednesday, May 16, 2018 3:37 PM To: app_rpt-users(a)lists.allstarlink.org Subject: Re: [App_rpt-users] Node Type One thing the USBradio needs to act as a COS or decode CTCSS is access to unfiltered audio from the receiver. In the case of the Boefeng, you do not have access to that unfiltered audio. The receive audio you are picking off is already filtered (deemphasized) so you can not use the COS or CTCSS feature of USBradio. Steve N4IRS On 5/16/2018 3:32 PM, KD2NFC, Joe Puma wrote: > Steve what method do you think is more reliable, simple usb or usb audio? Allowing the radio to do CTCSS or Usb driver? I like the idea that when the radio is doing ctcss and on baofeng that means there’s no power to the audio op amp until it detects ctcss vs leaving the squelch open on radio and the op amp always on. What would you think is best in regards to response time also. > > > Joe > KD2NFC > > > > Sent from my iPad > >> On May 16, 2018, at 3:14 PM, Steve Zingman <szingman(a)msgstor.com> wrote: >> >> Sorry, I forgot that one: >> A URI, USB FOB, RA-42 and others are all USB radio interfaces. >> Beagle NHRC are host specific Radio interfaces. Just forget NHRC and Dingotel >> >> USBradio and simpleUSB are the 2 methods of utilizing those USB interfaces. SimpleUSB is just that, simple. It uses GPIO pins on the audio device for signaling (COS, CTCSS and PTT) It also connects the RX and TX audio from radio. In the case of CTCSS, a CTCSS decoder is required to signal the receipt of a CTCSS encoded RF signal. >> >> USBRadio can generate and decode CTCSS without external hardware. It can also operate as the COS. In this case only TX audio, RX audio and PTT are required to be connected to the radio. >> >> 73, Steve N4IRS >> >>> On 5/16/2018 3:02 PM, mwbesemer(a)cox.net wrote: >>> Exactly the opposite. I want it to be be visible and clearly show that it is connected to a repeater (via an RF link) and NOT just some local ham's radio attached to a 5/8 wave Hustler for his personal use around the house. >>> >>> I'm learning and asking questions now, BEFORE I paint myself into a corner. Steve gave me what I needed. I'll admit up front, I'm an electronics guy, not a programmer. I had a career in electronics and know what I'm doing there. The rest of this is kinda new to me, and I believe in doing stuff once - and doing it right. >>> >>> Still unanswered is my question about Interface Type and Variety. >>> >>> "And while I'm at it, what about Interface Type (usbradio, simpleusb, or beagle) and Interface Variety (URI or USB FOB, NHRC, or Dingotel). I'll be using one of Kevin Custers RA-42's." >>> >>> Mike >>> WM4B >>> >>> >>>> On Wed, May 16, 2018 at 2:51 PM, Mike wrote: >>>> >>>> Perhaps what you are really looking for is the method to mask it showing publicly as a resource. >>>> >>>> More like a private node ? >>>> >>>> Anyway, I think now that is what you were asking or need. Perhaps I am wrong. >>>> >>>> 73, >>>> >>>> ...mike/kb8jnm >>>> >>>> >>>>> On 5/16/2018 2:22 PM, mwbesemer(a)cox.net wrote: >>>>> Answered below... it is NOT frequency agile... that's a no brainer for me. >>>>> >>>>> But... it's not a repeater either. >>>>> >>>>> Yes... it's simplex, but it is not intended for other hams to work into the repeater through it; it's only there to connect the node to the repeater. If I list it as a simplex node, then nobody on the far-side will know that it's connected to a repeater - they'll just assume it spews out RF into a small, local area. >>>>> >>>>> In setting up the node on the website, there are separate selections for 'Remote Base' and 'Frequency Agile'. If you're saying I should NOT set it up as a non-frequency agile remote base, please explain why. >>>>> >>>>> Maybe I'm hung up on the definition of 'repeater' and 'remote base'. >>>>> >>>>> Mike >>>>> WM4B >>>>> >>>>> >>>>>> On Wed, May 16, 2018 at 2:09 PM, Mike wrote: >>>>>> >>>>>> I was pretty sure of why you were asking but carefull if you were not providing all the info. >>>>>> >>>>>> It's about the radio attached to the node. >>>>>> >>>>>> can it change freq - Y , then it is freq agile >>>>>> >>>>>> - N then is it simplex or a repeater >>>>>> >>>>>> so if I connect to your node, what radio am I going to get ? >>>>>> >>>>>> ...mike/kb8jnm >>>>>> >>>>>> >>>>>>> On 5/16/2018 2:05 PM, mwbesemer(a)cox.net wrote: >>>>>>> Perhaps a better way to phrase my question would be: >>>>>>> >>>>>>> When setting up the Radio Configuration for the node (on allstarlink.org) what is the node type? My choices are Repeater (full duplex), Simplex, Simplex with CT, or Remote Base. >>>>>>> >>>>>>> My thought process would be that 'Repeater' would be used if the node was physically attached to the repeater (through the controller), Simplex would be used to allow local stations to access ASL via RF, and that Remote Base is used to link the node to a repeater via RF (which is what I'm doing). >>>>>>> >>>>>>> Am I all wet? >>>>>>> >>>>>>> And while I'm at it, what about Interface Type (usbradio, simpleusb, or beagle) and Interface Variety (URI or USB FOB, NHRC, or Dingotel). I'll be using one of Kevin Custers RA-42's. >>>>>>> >>>>>>> Tnx, >>>>>>> >>>>>>> Mike - WM4B >>>>>>> >>>>>>> >>>>>>>> On Wed, May 16, 2018 at 1:44 PM, mwbesemer(a)cox.net wrote: >>>>>>>> >>>>>>>> "links to the repeater only via the repeater input/output"... so no. >>>>>>>> >>>>>>>> Mike >>>>>>>> WM4B >>>>>>>> >>>>>>>>> On Wed, May 16, 2018 at 1:40 PM, Mike wrote: >>>>>>>>> >>>>>>>>> Can you change the freq of operation of the radio attached by command 'within/though" this node # ? >>>>>>>>> >>>>>>>>> ...is the answer to your question. location does not matter. >>>>>>>>> >>>>>>>>> >>>>>>>>> ...mike/kb8jnm >>>>>>>>> >>>>>>>>> >>>>>>>>>> On 5/16/2018 12:54 PM, mwbesemer(a)cox.net wrote: >>>>>>>>>> If a node is established at a location different from that of the repeater and links to the repeater only via the repeater input/output, would it be considered a non-frequency agile remote-base? >>>>>>>>>> >>>>>>>>>> Mike >>>>>>>>>> WM4B >>>>>>>>>> _______________________________________________ >>>>>>>>>> App_rpt-users mailing list >>>>>>>>>> App_rpt-users(a)lists.allstarlink.org >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>>>>>> >>>>>>>>>> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" >>>>>>>>>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. >>>>>>>>> _______________________________________________ >>>>>>>>> App_rpt-users mailing list >>>>>>>>> App_rpt-users(a)lists.allstarlink.org >>>>>>>>> >>>>>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>>>>> >>>>>>>>> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" >>>>>>>>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. >>>>>>>> _______________________________________________ >>>>>>>> App_rpt-users mailing list >>>>>>>> App_rpt-users(a)lists.allstarlink.org >>>>>>>> >>>>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>>>> >>>>>>>> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" >>>>>>>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. >>>>>>> _______________________________________________ >>>>>>> App_rpt-users mailing list >>>>>>> App_rpt-users(a)lists.allstarlink.org >>>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>>> >>>>>>> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" >>>>>>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. >>>> _______________________________________________ >>>> App_rpt-users mailing list >>>> App_rpt-users(a)lists.allstarlink.org >>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>> >>>> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" >>>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. >>> _______________________________________________ >>> App_rpt-users mailing list >>> App_rpt-users(a)lists.allstarlink.org >>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>> >>> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" >>> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. >> _______________________________________________ >> App_rpt-users mailing list >> App_rpt-users(a)lists.allstarlink.org >> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >> >> To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" >> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)lists.allstarlink.org > http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users(a)lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

1 0

Re: [App_rpt-users] Node Type
by Mike Besemer 16 May '18

16 May '18

Awesome Steve... thanks again. " Just forget NHRC and Dingotel" Too bad... Dingote is a great name! Mike WM4B -----Original Message----- From: App_rpt-users [mailto:app_rpt-users-bounces@lists.allstarlink.org] On Behalf Of Steve Zingman Sent: Wednesday, May 16, 2018 3:15 PM To: app_rpt-users(a)lists.allstarlink.org Subject: Re: [App_rpt-users] Node Type Sorry, I forgot that one: A URI, USB FOB, RA-42 and others are all USB radio interfaces. Beagle NHRC are host specific Radio interfaces. Just forget NHRC and Dingotel USBradio and simpleUSB are the 2 methods of utilizing those USB interfaces. SimpleUSB is just that, simple. It uses GPIO pins on the audio device for signaling (COS, CTCSS and PTT) It also connects the RX and TX audio from radio. In the case of CTCSS, a CTCSS decoder is required to signal the receipt of a CTCSS encoded RF signal. USBRadio can generate and decode CTCSS without external hardware. It can also operate as the COS. In this case only TX audio, RX audio and PTT are required to be connected to the radio. 73, Steve N4IRS On 5/16/2018 3:02 PM, mwbesemer(a)cox.net wrote: > Exactly the opposite. I want it to be be visible and clearly show > that it is connected to a repeater (via an RF link) and NOT just some > local ham's radio attached to a 5/8 wave Hustler for his personal use > around the house. > > I'm learning and asking questions now, BEFORE I paint myself into a > corner. Steve gave me what I needed. I'll admit up front, I'm an > electronics guy, not a programmer. I had a career in electronics and > know what I'm doing there. The rest of this is kinda new to me, and I > believe in doing stuff once - and doing it right. > > Still unanswered is my question about Interface Type and Variety. > > "And while I'm at it, what about Interface Type (usbradio, simpleusb, > or beagle) and Interface Variety (URI or USB FOB, NHRC, or Dingotel). > I'll be using one of Kevin Custers RA-42's." > > Mike > WM4B > > > On Wed, May 16, 2018 at 2:51 PM, Mike wrote: > >> Perhaps what you are really looking for is the method to mask it >> showing publicly as a resource. >> >> More like a private node ? >> >> Anyway, I think now that is what you were asking or need. Perhaps I >> am wrong. >> >> 73, >> >> ...mike/kb8jnm >> >> >> On 5/16/2018 2:22 PM, mwbesemer(a)cox.net wrote: >>> Answered below... it is NOT frequency agile... that's a no brainer >>> for me. >>> >>> But... it's not a repeater either. >>> >>> Yes... it's simplex, but it is not intended for other hams to work >>> into the repeater through it; it's only there to connect the node to >>> the repeater. If I list it as a simplex node, then nobody on the >>> far-side will know that it's connected to a repeater - they'll just >>> assume it spews out RF into a small, local area. >>> >>> In setting up the node on the website, there are separate selections >>> for 'Remote Base' and 'Frequency Agile'. If you're saying I should >>> NOT set it up as a non-frequency agile remote base, please explain why. >>> >>> Maybe I'm hung up on the definition of 'repeater' and 'remote base'. >>> >>> Mike >>> WM4B >>> >>> >>> On Wed, May 16, 2018 at 2:09 PM, Mike wrote: >>> >>>> I was pretty sure of why you were asking but carefull if you were >>>> not providing all the info. >>>> >>>> It's about the radio attached to the node. >>>> >>>> can it change freq - Y , then it is freq agile >>>> >>>> - N then is it simplex or a repeater >>>> >>>> so if I connect to your node, what radio am I going to get ? >>>> >>>> ...mike/kb8jnm >>>> >>>> >>>> On 5/16/2018 2:05 PM, mwbesemer(a)cox.net wrote: >>>>> Perhaps a better way to phrase my question would be: >>>>> >>>>> When setting up the Radio Configuration for the node (on >>>>> allstarlink.org) what is the node type? My choices are Repeater >>>>> (full duplex), Simplex, Simplex with CT, or Remote Base. >>>>> >>>>> My thought process would be that 'Repeater' would be used if the >>>>> node was physically attached to the repeater (through the >>>>> controller), Simplex would be used to allow local stations to >>>>> access ASL via RF, and that Remote Base is used to link the node >>>>> to a repeater via RF (which is what I'm doing). >>>>> >>>>> Am I all wet? >>>>> >>>>> And while I'm at it, what about Interface Type (usbradio, >>>>> simpleusb, or beagle) and Interface Variety (URI or USB FOB, NHRC, >>>>> or Dingotel). I'll be using one of Kevin Custers RA-42's. >>>>> >>>>> Tnx, >>>>> >>>>> Mike - WM4B >>>>> >>>>> >>>>> On Wed, May 16, 2018 at 1:44 PM, mwbesemer(a)cox.net wrote: >>>>> >>>>>> "links to the repeater only via the repeater input/output"... so no. >>>>>> >>>>>> Mike >>>>>> WM4B >>>>>> >>>>>> On Wed, May 16, 2018 at 1:40 PM, Mike wrote: >>>>>> >>>>>>> Can you change the freq of operation of the radio attached by >>>>>>> command 'within/though" this node # ? >>>>>>> >>>>>>> ...is the answer to your question. location does not matter. >>>>>>> >>>>>>> >>>>>>> ...mike/kb8jnm >>>>>>> >>>>>>> >>>>>>> On 5/16/2018 12:54 PM, mwbesemer(a)cox.net wrote: >>>>>>>> If a node is established at a location different from that of >>>>>>>> the repeater and links to the repeater only via the repeater >>>>>>>> input/output, would it be considered a non-frequency agile >>>>>>>> remote-base? >>>>>>>> >>>>>>>> Mike >>>>>>>> WM4B >>>>>>>> _______________________________________________ >>>>>>>> App_rpt-users mailing list >>>>>>>> App_rpt-users(a)lists.allstarlink.org >>>>>>>> >>>>>>>> >>>>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>>>> >>>>>>>> >>>>>>>> To unsubscribe from this list please visit >>>>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>>>> and scroll down to the bottom of the page. Enter your email >>>>>>>> address and press the "Unsubscribe or edit options button" >>>>>>>> You do not need a password to unsubscribe, you can do it via >>>>>>>> email confirmation. If you have trouble unsubscribing, please >>>>>>>> send a message to the list detailing the problem. >>>>>>> >>>>>>> _______________________________________________ >>>>>>> App_rpt-users mailing list >>>>>>> App_rpt-users(a)lists.allstarlink.org >>>>>>> >>>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>>> >>>>>>> To unsubscribe from this list please visit >>>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>>> and scroll down to the bottom of the page. Enter your email >>>>>>> address and press the "Unsubscribe or edit options button" >>>>>>> You do not need a password to unsubscribe, you can do it via >>>>>>> email confirmation. If you have trouble unsubscribing, please >>>>>>> send a message to the list detailing the problem. >>>>>> _______________________________________________ >>>>>> App_rpt-users mailing list >>>>>> App_rpt-users(a)lists.allstarlink.org >>>>>> >>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>> >>>>>> To unsubscribe from this list please visit >>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>> and scroll down to the bottom of the page. Enter your email >>>>>> address and press the "Unsubscribe or edit options button" >>>>>> You do not need a password to unsubscribe, you can do it via >>>>>> email confirmation. If you have trouble unsubscribing, please >>>>>> send a message to the list detailing the problem. >>>>> _______________________________________________ >>>>> App_rpt-users mailing list >>>>> App_rpt-users(a)lists.allstarlink.org >>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>> >>>>> To unsubscribe from this list please visit >>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>> and scroll down to the bottom of the page. Enter your email >>>>> address and press the "Unsubscribe or edit options button" >>>>> You do not need a password to unsubscribe, you can do it via email >>>>> confirmation. If you have trouble unsubscribing, please send a >>>>> message to the list detailing the problem. >> >> _______________________________________________ >> App_rpt-users mailing list >> App_rpt-users(a)lists.allstarlink.org >> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >> >> To unsubscribe from this list please visit >> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >> and scroll down to the bottom of the page. Enter your email address >> and press the "Unsubscribe or edit options button" >> You do not need a password to unsubscribe, you can do it via email >> confirmation. If you have trouble unsubscribing, please send a >> message to the list detailing the problem. > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)lists.allstarlink.org > http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit > http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > and scroll down to the bottom of the page. Enter your email address > and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message > to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users(a)lists.allstarlink.org http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

1 0

Re: [App_rpt-users] Node Type
by mwbesemer＠cox.net 16 May '18

16 May '18

Exactly the opposite. I want it to be be visible and clearly show that it is connected to a repeater (via an RF link) and NOT just some local ham's radio attached to a 5/8 wave Hustler for his personal use around the house. I'm learning and asking questions now, BEFORE I paint myself into a corner. Steve gave me what I needed. I'll admit up front, I'm an electronics guy, not a programmer. I had a career in electronics and know what I'm doing there. The rest of this is kinda new to me, and I believe in doing stuff once - and doing it right. Still unanswered is my question about Interface Type and Variety. "And while I'm at it, what about Interface Type (usbradio, simpleusb, or beagle) and Interface Variety (URI or USB FOB, NHRC, or Dingotel). I'll be using one of Kevin Custers RA-42's." Mike WM4B On Wed, May 16, 2018 at 2:51 PM, Mike wrote: > Perhaps what you are really looking for is the method to mask it > showing publicly as a resource. > > More like a private node ? > > Anyway, I think now that is what you were asking or need. Perhaps I am > wrong. > > 73, > > ...mike/kb8jnm > > > On 5/16/2018 2:22 PM, mwbesemer(a)cox.net wrote: >> Answered below... it is NOT frequency agile... that's a no brainer >> for me. >> >> But... it's not a repeater either. >> >> Yes... it's simplex, but it is not intended for other hams to work >> into the repeater through it; it's only there to connect the node to >> the repeater. If I list it as a simplex node, then nobody on the >> far-side will know that it's connected to a repeater - they'll just >> assume it spews out RF into a small, local area. >> >> In setting up the node on the website, there are separate selections >> for 'Remote Base' and 'Frequency Agile'. If you're saying I should >> NOT set it up as a non-frequency agile remote base, please explain >> why. >> >> Maybe I'm hung up on the definition of 'repeater' and 'remote base'. >> >> Mike >> WM4B >> >> >> On Wed, May 16, 2018 at 2:09 PM, Mike wrote: >> >>> I was pretty sure of why you were asking but carefull if you were >>> not providing all the info. >>> >>> It's about the radio attached to the node. >>> >>> can it change freq - Y , then it is freq agile >>> >>> - N then is it simplex or a repeater >>> >>> so if I connect to your node, what radio am I going to get ? >>> >>> ...mike/kb8jnm >>> >>> >>> On 5/16/2018 2:05 PM, mwbesemer(a)cox.net wrote: >>>> Perhaps a better way to phrase my question would be: >>>> >>>> When setting up the Radio Configuration for the node (on >>>> allstarlink.org) what is the node type? My choices are Repeater >>>> (full duplex), Simplex, Simplex with CT, or Remote Base. >>>> >>>> My thought process would be that 'Repeater' would be used if the >>>> node was physically attached to the repeater (through the >>>> controller), Simplex would be used to allow local stations to >>>> access ASL via RF, and that Remote Base is used to link the node to >>>> a repeater via RF (which is what I'm doing). >>>> >>>> Am I all wet? >>>> >>>> And while I'm at it, what about Interface Type (usbradio, >>>> simpleusb, or beagle) and Interface Variety (URI or USB FOB, NHRC, >>>> or Dingotel). I'll be using one of Kevin Custers RA-42's. >>>> >>>> Tnx, >>>> >>>> Mike - WM4B >>>> >>>> >>>> On Wed, May 16, 2018 at 1:44 PM, mwbesemer(a)cox.net wrote: >>>> >>>>> "links to the repeater only via the repeater input/output"... so >>>>> no. >>>>> >>>>> Mike >>>>> WM4B >>>>> >>>>> On Wed, May 16, 2018 at 1:40 PM, Mike wrote: >>>>> >>>>>> Can you change the freq of operation of the radio attached by >>>>>> command 'within/though" this node # ? >>>>>> >>>>>> ...is the answer to your question. location does not matter. >>>>>> >>>>>> >>>>>> ...mike/kb8jnm >>>>>> >>>>>> >>>>>> On 5/16/2018 12:54 PM, mwbesemer(a)cox.net wrote: >>>>>>> If a node is established at a location different from that of >>>>>>> the repeater and links to the repeater only via the repeater >>>>>>> input/output, would it be considered a non-frequency agile >>>>>>> remote-base? >>>>>>> >>>>>>> Mike >>>>>>> WM4B >>>>>>> _______________________________________________ >>>>>>> App_rpt-users mailing list >>>>>>> App_rpt-users(a)lists.allstarlink.org >>>>>>> >>>>>>> >>>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>>> >>>>>>> To unsubscribe from this list please visit >>>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>>> and scroll down to the bottom of the page. Enter your email >>>>>>> address and press the "Unsubscribe or edit options button" >>>>>>> You do not need a password to unsubscribe, you can do it via >>>>>>> email confirmation. If you have trouble unsubscribing, please >>>>>>> send a message to the list detailing the problem. >>>>>> >>>>>> _______________________________________________ >>>>>> App_rpt-users mailing list >>>>>> App_rpt-users(a)lists.allstarlink.org >>>>>> >>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>> >>>>>> To unsubscribe from this list please visit >>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>> and scroll down to the bottom of the page. Enter your email >>>>>> address and press the "Unsubscribe or edit options button" >>>>>> You do not need a password to unsubscribe, you can do it via >>>>>> email confirmation. If you have trouble unsubscribing, please >>>>>> send a message to the list detailing the problem. >>>>> _______________________________________________ >>>>> App_rpt-users mailing list >>>>> App_rpt-users(a)lists.allstarlink.org >>>>> >>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>> >>>>> To unsubscribe from this list please visit >>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>> and scroll down to the bottom of the page. Enter your email >>>>> address and press the "Unsubscribe or edit options button" >>>>> You do not need a password to unsubscribe, you can do it via email >>>>> confirmation. If you have trouble unsubscribing, please send a >>>>> message to the list detailing the problem. >>>> _______________________________________________ >>>> App_rpt-users mailing list >>>> App_rpt-users(a)lists.allstarlink.org >>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>> >>>> To unsubscribe from this list please visit >>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>> and scroll down to the bottom of the page. Enter your email address >>>> and press the "Unsubscribe or edit options button" >>>> You do not need a password to unsubscribe, you can do it via email >>>> confirmation. If you have trouble unsubscribing, please send a >>>> message to the list detailing the problem. > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)lists.allstarlink.org > http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit > http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > and scroll down to the bottom of the page. Enter your email address > and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message > to the list detailing the problem.

3 3

Re: [App_rpt-users] Node Type
by Mike 16 May '18

16 May '18

Perhaps what you are really looking for is the method to mask it showing publicly as a resource. More like a private node ? Anyway, I think now that is what you were asking or need. Perhaps I am wrong. 73, ...mike/kb8jnm On 5/16/2018 2:22 PM, mwbesemer(a)cox.net wrote: > Answered below... it is NOT frequency agile... that's a no brainer for > me. > > But... it's not a repeater either. > > Yes... it's simplex, but it is not intended for other hams to work > into the repeater through it; it's only there to connect the node to > the repeater. If I list it as a simplex node, then nobody on the > far-side will know that it's connected to a repeater - they'll just > assume it spews out RF into a small, local area. > > In setting up the node on the website, there are separate selections > for 'Remote Base' and 'Frequency Agile'. If you're saying I should > NOT set it up as a non-frequency agile remote base, please explain why. > > Maybe I'm hung up on the definition of 'repeater' and 'remote base'. > > Mike > WM4B > > > On Wed, May 16, 2018 at 2:09 PM, Mike wrote: > >> I was pretty sure of why you were asking but carefull if you were not >> providing all the info. >> >> It's about the radio attached to the node. >> >> can it change freq - Y , then it is freq agile >> >> - N then is it simplex or a repeater >> >> so if I connect to your node, what radio am I going to get ? >> >> ...mike/kb8jnm >> >> >> On 5/16/2018 2:05 PM, mwbesemer(a)cox.net wrote: >>> Perhaps a better way to phrase my question would be: >>> >>> When setting up the Radio Configuration for the node (on >>> allstarlink.org) what is the node type? My choices are Repeater >>> (full duplex), Simplex, Simplex with CT, or Remote Base. >>> >>> My thought process would be that 'Repeater' would be used if the >>> node was physically attached to the repeater (through the >>> controller), Simplex would be used to allow local stations to access >>> ASL via RF, and that Remote Base is used to link the node to a >>> repeater via RF (which is what I'm doing). >>> >>> Am I all wet? >>> >>> And while I'm at it, what about Interface Type (usbradio, simpleusb, >>> or beagle) and Interface Variety (URI or USB FOB, NHRC, or >>> Dingotel). I'll be using one of Kevin Custers RA-42's. >>> >>> Tnx, >>> >>> Mike - WM4B >>> >>> >>> On Wed, May 16, 2018 at 1:44 PM, mwbesemer(a)cox.net wrote: >>> >>>> "links to the repeater only via the repeater input/output"... so no. >>>> >>>> Mike >>>> WM4B >>>> >>>> On Wed, May 16, 2018 at 1:40 PM, Mike wrote: >>>> >>>>> Can you change the freq of operation of the radio attached by >>>>> command 'within/though" this node # ? >>>>> >>>>> ...is the answer to your question. location does not matter. >>>>> >>>>> >>>>> ...mike/kb8jnm >>>>> >>>>> >>>>> On 5/16/2018 12:54 PM, mwbesemer(a)cox.net wrote: >>>>>> If a node is established at a location different from that of the >>>>>> repeater and links to the repeater only via the repeater >>>>>> input/output, would it be considered a non-frequency agile >>>>>> remote-base? >>>>>> >>>>>> Mike >>>>>> WM4B >>>>>> _______________________________________________ >>>>>> App_rpt-users mailing list >>>>>> App_rpt-users(a)lists.allstarlink.org >>>>>> >>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>> >>>>>> To unsubscribe from this list please visit >>>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>>> and scroll down to the bottom of the page. Enter your email >>>>>> address and press the "Unsubscribe or edit options button" >>>>>> You do not need a password to unsubscribe, you can do it via >>>>>> email confirmation. If you have trouble unsubscribing, please >>>>>> send a message to the list detailing the problem. >>>>> >>>>> _______________________________________________ >>>>> App_rpt-users mailing list >>>>> App_rpt-users(a)lists.allstarlink.org >>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>> >>>>> To unsubscribe from this list please visit >>>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>>> and scroll down to the bottom of the page. Enter your email >>>>> address and press the "Unsubscribe or edit options button" >>>>> You do not need a password to unsubscribe, you can do it via email >>>>> confirmation. If you have trouble unsubscribing, please send a >>>>> message to the list detailing the problem. >>>> _______________________________________________ >>>> App_rpt-users mailing list >>>> App_rpt-users(a)lists.allstarlink.org >>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>> >>>> To unsubscribe from this list please visit >>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>>> and scroll down to the bottom of the page. Enter your email address >>>> and press the "Unsubscribe or edit options button" >>>> You do not need a password to unsubscribe, you can do it via email >>>> confirmation. If you have trouble unsubscribing, please send a >>>> message to the list detailing the problem. >>> _______________________________________________ >>> App_rpt-users mailing list >>> App_rpt-users(a)lists.allstarlink.org >>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>> >>> To unsubscribe from this list please visit >>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>> and scroll down to the bottom of the page. Enter your email address >>> and press the "Unsubscribe or edit options button" >>> You do not need a password to unsubscribe, you can do it via email >>> confirmation. If you have trouble unsubscribing, please send a >>> message to the list detailing the problem.

1 0

Re: [App_rpt-users] Node Type
by Michael Besemer 16 May '18

16 May '18

BINGO! Thanks Steve! Mike WM4B On May 16, 2018 2:32 PM, Steve Zingman <szingman(a)msgstor.com> wrote: > > Repeater: > Usually connected to a full duplex station. AllStarLink is the repeater > controller. > > Simplex with telemetry (CT): > Usually connected to a simplex station. Operates as a RF "hotspot" > > Simplex without telemetry: > Usually connected to a existing repeater controller. Porvides > AllStarLink access to the repeater. > > Remote Base: > Usually a second radio connected to the AllStarLink node to provide node > access to a radio at a superior location. May be frequency agile. > > 73, Steve N4IRS > > On 5/16/2018 2:05 PM, mwbesemer(a)cox.net wrote: > > Perhaps a better way to phrase my question would be: > > > > When setting up the Radio Configuration for the node (on > > allstarlink.org) what is the node type? My choices are Repeater > > (full duplex), Simplex, Simplex with CT, or Remote Base. > > > > My thought process would be that 'Repeater' would be used if the node > > was physically attached to the repeater (through the controller), > > Simplex would be used to allow local stations to access ASL via RF, > > and that Remote Base is used to link the node to a repeater via RF > > (which is what I'm doing). > > > > Am I all wet? > > > > And while I'm at it, what about Interface Type (usbradio, simpleusb, > > or beagle) and Interface Variety (URI or USB FOB, NHRC, or Dingotel). > > I'll be using one of Kevin Custers RA-42's. > > > > Tnx, > > > > Mike - WM4B > > > > > > On Wed, May 16, 2018 at 1:44 PM, mwbesemer(a)cox.net wrote: > > > >> "links to the repeater only via the repeater input/output"... so no. > >> > >> Mike > >> WM4B > >> > >> On Wed, May 16, 2018 at 1:40 PM, Mike wrote: > >> > >>> Can you change the freq of operation of the radio attached by > >>> command 'within/though" this node # ? > >>> > >>> ...is the answer to your question. location does not matter. > >>> > >>> > >>> ...mike/kb8jnm > >>> > >>> > >>> On 5/16/2018 12:54 PM, mwbesemer(a)cox.net wrote: > >>>> If a node is established at a location different from that of the > >>>> repeater and links to the repeater only via the repeater > >>>> input/output, would it be considered a non-frequency agile > >>>> remote-base? > >>>> > >>>> Mike > >>>> WM4B > >>>> _______________________________________________ > >>>> App_rpt-users mailing list > >>>> App_rpt-users(a)lists.allstarlink.org > >>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > >>>> > >>>> To unsubscribe from this list please visit > >>>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > >>>> and scroll down to the bottom of the page. Enter your email address > >>>> and press the "Unsubscribe or edit options button" > >>>> You do not need a password to unsubscribe, you can do it via email > >>>> confirmation. If you have trouble unsubscribing, please send a > >>>> message to the list detailing the problem. > >>> > >>> _______________________________________________ > >>> App_rpt-users mailing list > >>> App_rpt-users(a)lists.allstarlink.org > >>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > >>> > >>> To unsubscribe from this list please visit > >>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > >>> and scroll down to the bottom of the page. Enter your email address > >>> and press the "Unsubscribe or edit options button" > >>> You do not need a password to unsubscribe, you can do it via email > >>> confirmation. If you have trouble unsubscribing, please send a > >>> message to the list detailing the problem. > >> _______________________________________________ > >> App_rpt-users mailing list > >> App_rpt-users(a)lists.allstarlink.org > >> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > >> > >> To unsubscribe from this list please visit > >> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > >> and scroll down to the bottom of the page. Enter your email address > >> and press the "Unsubscribe or edit options button" > >> You do not need a password to unsubscribe, you can do it via email > >> confirmation. If you have trouble unsubscribing, please send a > >> message to the list detailing the problem. > > _______________________________________________ > > App_rpt-users mailing list > > App_rpt-users(a)lists.allstarlink.org > > http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > > > > To unsubscribe from this list please visit > > http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > > and scroll down to the bottom of the page. Enter your email address > > and press the "Unsubscribe or edit options button" > > You do not need a password to unsubscribe, you can do it via email > > confirmation. If you have trouble unsubscribing, please send a message > > to the list detailing the problem. > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)lists.allstarlink.org > http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

1 0

Re: [App_rpt-users] Node Type
by mwbesemer＠cox.net 16 May '18

16 May '18

Perhaps a better way to phrase my question would be: When setting up the Radio Configuration for the node (on allstarlink.org) what is the node type? My choices are Repeater (full duplex), Simplex, Simplex with CT, or Remote Base. My thought process would be that 'Repeater' would be used if the node was physically attached to the repeater (through the controller), Simplex would be used to allow local stations to access ASL via RF, and that Remote Base is used to link the node to a repeater via RF (which is what I'm doing). Am I all wet? And while I'm at it, what about Interface Type (usbradio, simpleusb, or beagle) and Interface Variety (URI or USB FOB, NHRC, or Dingotel). I'll be using one of Kevin Custers RA-42's. Tnx, Mike - WM4B On Wed, May 16, 2018 at 1:44 PM, mwbesemer(a)cox.net wrote: > "links to the repeater only via the repeater input/output"... so no. > > Mike > WM4B > > On Wed, May 16, 2018 at 1:40 PM, Mike wrote: > >> Can you change the freq of operation of the radio attached by command >> 'within/though" this node # ? >> >> ...is the answer to your question. location does not matter. >> >> >> ...mike/kb8jnm >> >> >> On 5/16/2018 12:54 PM, mwbesemer(a)cox.net wrote: >>> If a node is established at a location different from that of the >>> repeater and links to the repeater only via the repeater >>> input/output, would it be considered a non-frequency agile >>> remote-base? >>> >>> Mike >>> WM4B >>> _______________________________________________ >>> App_rpt-users mailing list >>> App_rpt-users(a)lists.allstarlink.org >>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>> >>> To unsubscribe from this list please visit >>> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >>> and scroll down to the bottom of the page. Enter your email address >>> and press the "Unsubscribe or edit options button" >>> You do not need a password to unsubscribe, you can do it via email >>> confirmation. If you have trouble unsubscribing, please send a >>> message to the list detailing the problem. >> >> _______________________________________________ >> App_rpt-users mailing list >> App_rpt-users(a)lists.allstarlink.org >> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >> >> To unsubscribe from this list please visit >> http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users >> and scroll down to the bottom of the page. Enter your email address >> and press the "Unsubscribe or edit options button" >> You do not need a password to unsubscribe, you can do it via email >> confirmation. If you have trouble unsubscribing, please send a >> message to the list detailing the problem. > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)lists.allstarlink.org > http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > > To unsubscribe from this list please visit > http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users > and scroll down to the bottom of the page. Enter your email address > and press the "Unsubscribe or edit options button" > You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message > to the list detailing the problem.

2 1

ASL v 1.0.1 not connecting to any HUB or node
by Alberto Enrique Puig 16 May '18

16 May '18

Pierre VE2PF Pinging either 8.8.8.8. or www.google.com<http://www.google.com> works fine...Still trying to find out why updatenodelist is not running on my environment. Thanks for replying. 73, Alberto KP4AP ________________________________ From: App_rpt-users <app_rpt-users-bounces(a)lists.allstarlink.org> on behalf of app_rpt-users-request(a)lists.allstarlink.org <app_rpt-users-request(a)lists.allstarlink.org> Sent: Tuesday, May 15, 2018 12:00 PM To: app_rpt-users(a)lists.allstarlink.org Subject: App_rpt-users Digest, Vol 111, Issue 11 Send App_rpt-users mailing list submissions to app_rpt-users(a)lists.allstarlink.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users App_rpt-users Info Page - lists.allstarlink.org<http://lists.allstarlink.org/cgi-bin/mailman/listinfo/app_rpt-users> lists.allstarlink.org Your email address: Your name (optional): You may enter a privacy password below. This provides only mild security, but should prevent others from messing with your subscription. or, via email, send a message with subject or body 'help' to app_rpt-users-request(a)lists.allstarlink.org You can reach the person managing the list at app_rpt-users-owner(a)lists.allstarlink.org When replying, please edit your Subject line so it is more specific than "Re: Contents of App_rpt-users digest..." This site is dedicated to the memory of Jim Dixon WB6NIL Today's Topics: 1. AWS hosted ASL install? (Russell Thomas) 2. ASL with Pi 3 B+? (mwbesemer(a)cox.net) 3. Re: AWS hosted ASL install? (Russell Thomas) 4. Re: AWS hosted ASL install? (Tom Hayward) 5. Re: AWS hosted ASL install? (Russell Thomas) 6. Re: AWS hosted ASL install? (Tom Hayward) 7. Re: ASL with Pi 3 B+? (Steve Zingman) 8. Re: AWS hosted ASL install? (Russell Thomas) 9. Re: AWS hosted ASL install? (Russell Thomas) 10. Re: AWS hosted ASL install? (Tom Hayward) 11. Re: New ASL v 1.0.1 not connecting to any HUB or Node (Pierre Martel) 12. ASL Deployed on a VPS in under 1 hour as HUB (Mike) 13. New ASL v 1.0.1 not connecting to any HUB or Node (Alberto Enrique Puig) 14. Re: New ASL v 1.0.1 not connecting to any HUB or Node (Steve Zingman) ---------------------------------------------------------------------- Message: 1 Date: Mon, 14 May 2018 11:51:35 -0500 From: Russell Thomas <russell(a)kv4s.com> To: app_rpt-users(a)lists.allstarlink.org Subject: [App_rpt-users] AWS hosted ASL install? Message-ID: <CAANUOmHxcjAydiUedYqyVCp1JnE4Arefin4kmsg9vaaffhWnnQ(a)mail.gmail.com> Content-Type: text/plain; charset="utf-8" I was interested in installing a cloud version of ASL to see if I could setup a DVSwitch project. I have a linux virtual server running linux. I went by the following instructions: https://wiki.allstarlink.org/wiki/ASL_FAQ but i'm getting messages and i'm not sure how to correct it? 73, Russell Thomas, KV4S Cell: 205.202.1701 DMR: 3101393 D-Star: KV4S AllStar: 47923 EchoLink: KV4S-L HamShackHotline: 4225 Web: http://KV4S.com

3 2