August 2013 - App_rpt-users - lists.keekles.org

recomindations for motherboards for Limey
by C B 25 Aug '13

25 Aug '13

Hi is there a standard or recommended motherboard for the Limey Linux? The ones listed on the Limey page seem to be End Of Life. Thank you Chris

1 0

Re: [App_rpt-users] Asterisk ended with exit status 1
by C B 25 Aug '13

25 Aug '13

Hi tried this and no luck. I updated the BIOS no luck. I am lost. thank you Chris ________________________________ From: Jeff Carrier <k0jsc.jeff(a)gmail.com> To: C B <harvard5362(a)yahoo.com> Sent: Sunday, August 25, 2013 11:20 AM Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 I normally do this when I see this issue. I have a node that has the error frequently. 1. Remove the old source tree, grab the source tarball and uncompress into a new source tree, build it, and install it: cd /usr/src rm -rf astsrc-old mv astsrc astsrc-old wget http://x.allstarlink.org/svn-trunk.tar.gz -O- | tar xzv mv trunk astsrc cd astsrc make upgrade-acid 2. Restart asterisk astres.sh 73 de K0JSC On Sun, Aug 25, 2013 at 12:10 PM, C B <harvard5362(a)yahoo.com> wrote: Hi > >I did what you suggested and it seems to complete without error. > >However it did not resolve the problem. > >I ran the same commands for Asterisk, still the same issue. > >Reran the Zaptel compile / install again and still no luck. > >I re-downloaded for the allstarlink.org the ISO for ACID in case what I downloaded originally was corrupt. > >after reinstalling I looked at the /root/acidinstall.log and I did not see anything that looked like an error. > >Am I forgetting something or could my hardware not be combatable? > >As part of this project I did install this successfully on a different computer. > >Any help greatly appreciated. > >Chris > > >From: Paul J. Agamata <Sysman(a)Xceptions.COM> >To: C B <harvard5362(a)yahoo.com> >Sent: Saturday, August 24, 2013 4:57 PM >Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 > > > >Log into your 'root' account and navigate to the 'zaptel' directory. > > >When your in there type the following: > > >./configure <enter> >make <enter> >make install <enter> > > >Then reboot your computer and everything should be fine. >_______________________________ >Paul J. Agamata >WH6FM >Sysman(a)Xceptions.COM >Hilo, Hawaii > > > >From: C B <harvard5362(a)yahoo.com> >Reply-To: C B <harvard5362(a)yahoo.com> >Date: Saturday, August 24, 2013 1:54 PM >To: Paul Agamata <Sysman(a)Xceptions.COM> >Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 > > > >Paul > >Please excuse my lack knowledge here, I am very unsure of the compile / install procedure you are speaking of. > >is there anything you can refer me to that will contain instructions on how to do this? > >Is it something I did wrong? > >Sorry for not having a lot of experience. > >And thank you for your help. > >Chris > > >From: Paul J. Agamata <Sysman(a)Xceptions.COM> >To: C B <harvard5362(a)yahoo.com>; "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> >Sent: Saturday, August 24, 2013 4:46 PM >Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 > > > >This is indicative of the zaptel drivers not in your kernel. Compile/Install then reboot and all should be well. The 'zaptel' directory is in the 'asterisk' source directory. > > >Be aware that if you update your kernel you will need to re-install the zaptel modules. > > >Regards, >Paul > > >_______________________________ >Paul J. Agamata >WH6FM >Sysman(a)Xceptions.COM >Hilo, Hawaii > > > >From: C B <harvard5362(a)yahoo.com> >Date: Saturday, August 24, 2013 1:23 PM >To: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> >Subject: [App_rpt-users] Asterisk ended with exit status 1 > > > >Hi > >I am attempting to build a ACID node. > >After several attempts of reinstalling the ACID with the same results I am asking for some help. > >All seems to complete normally, I download the configuration, reboot and the following error message keeps repeating. > >mpg123: no process killed >Asterisk ended with exit status 1 >Asterisk died with code 1 >Automatically restarting Asterisk > >Computer is a HPdc5700 small form factor >1 GIG memory >500 GB SATA HDD > >than you in advance for any help > >Chris > > > > > >_______________________________________________ >App_rpt-users mailing list >App_rpt-users(a)ohnosec.org >http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > >

1 0

Re: [App_rpt-users] Asterisk ended with exit status 1
by C B 25 Aug '13

25 Aug '13

Hi I believe I only enabled the COR. it would seem that I should find a older computer perhaps. Chris ________________________________ From: Pierre Martel <petem001(a)hotmail.com> To: C B <harvard5362(a)yahoo.com> Sent: Sunday, August 25, 2013 1:37 PM Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 I had the same problem and was suspecting dsp. I did un update to latest svn. and was stillg etting same thing. Are you using any dsp on your node? ctcss decoding, cor, ect? From: C B Sent: Sunday, August 25, 2013 2:10 PM To: Paul J. Agamata ; app_rpt-users(a)ohnosec.org Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 Hi I did what you suggested and it seems to complete without error. However it did not resolve the problem. I ran the same commands for Asterisk, still the same issue. Reran the Zaptel compile / install again and still no luck. I re-downloaded for the allstarlink.org the ISO for ACID in case what I downloaded originally was corrupt. after reinstalling I looked at the /root/acidinstall.log and I did not see anything that looked like an error. Am I forgetting something or could my hardware not be combatable? As part of this project I did install this successfully on a different computer. Any help greatly appreciated. Chris ________________________________ From: Paul J. Agamata <Sysman(a)Xceptions.COM> To: C B <harvard5362(a)yahoo.com> Sent: Saturday, August 24, 2013 4:57 PM Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 Log into your 'root' account and navigate to the 'zaptel' directory. When your in there type the following: ./configure <enter> make <enter> make install <enter> Then reboot your computer and everything should be fine. _______________________________ Paul J. Agamata WH6FM Sysman(a)Xceptions.COM Hilo, Hawaii From: C B <harvard5362(a)yahoo.com> Reply-To: C B <harvard5362(a)yahoo.com> Date: Saturday, August 24, 2013 1:54 PM To: Paul Agamata <Sysman(a)Xceptions.COM> Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 Paul Please excuse my lack knowledge here, I am very unsure of the compile / install procedure you are speaking of. is there anything you can refer me to that will contain instructions on how to do this? Is it something I did wrong? Sorry for not having a lot of experience. And thank you for your help. Chris ________________________________ From: Paul J. Agamata <Sysman(a)Xceptions.COM> To: C B <harvard5362(a)yahoo.com>; "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> Sent: Saturday, August 24, 2013 4:46 PM Subject: Re: [App_rpt-users] Asterisk ended with exit status 1 This is indicative of the zaptel drivers not in your kernel. Compile/Install then reboot and all should be well. The 'zaptel' directory is in the 'asterisk' source directory. Be aware that if you update your kernel you will need to re-install the zaptel modules. Regards, Paul _______________________________ Paul J. Agamata WH6FM Sysman(a)Xceptions.COM Hilo, Hawaii From: C B <harvard5362(a)yahoo.com> Date: Saturday, August 24, 2013 1:23 PM To: "app_rpt-users(a)ohnosec.org" <app_rpt-users(a)ohnosec.org> Subject: [App_rpt-users] Asterisk ended with exit status 1 Hi I am attempting to build a ACID node. After several attempts of reinstalling the ACID with the same results I am asking for some help. All seems to complete normally, I download the configuration, reboot and the following error message keeps repeating. mpg123: no process killed Asterisk ended with exit status 1 Asterisk died with code 1 Automatically restarting Asterisk Computer is a HPdc5700 small form factor 1 GIG memory 500 GB SATA HDD than you in advance for any help Chris ________________________________ _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users

1 0

keeping connections permanent
by C B 25 Aug '13

25 Aug '13

Hi how do I make my connections between my nodes permanent. they seem to drop from time to time. Chris

5 5

Asterisk ended with exit status 1
by C B 24 Aug '13

24 Aug '13

Hi I am attempting to build a ACID node. After several attempts of reinstalling the ACID with the same results I am asking for some help. All seems to complete normally, I download the configuration, reboot and the following error message keeps repeating. mpg123: no process killed Asterisk ended with exit status 1 Asterisk died with code 1 Automatically restarting Asterisk Computer is a HPdc5700 small form factor 1 GIG memory 500 GB SATA HDD than you in advance for any help Chris

2 1

Re: [App_rpt-users] keeping connections permanent
by Bryan D. Boyle 24 Aug '13

24 Aug '13

On 8/24/2013 6:43 PM, KJ6KO wrote: > Thanks...Exactly what I am planning! Have the HUB and am adding more > nodes slowly! > Would it be best to set the HUB up for the perm links or the outlying > nodes? I assume the hub, but we all know what happens when you > "assume". hi hi My own opinion is worth what it'll cost you (0), since there are probably as many thoughts regarding this as subs to the list and variety of networks built with the software, from the simplest 4 or radio interconnection schemes to the borg-like WAN system (said with affection, ok?)...however, that being said, from a risk analysis and continuity of operations standpoint...I'd initiate the permalink from the hub out. One less thing for the spokes to worry about, and since the hub is the hub (how's that for a redundant statement) or core of the net...makes sense to have it do what it's doing (interconnecting N+1 repeaters) and let the leaves do what they do: managing the radio interfaces and forwarding the audio back to the mother ship. I'm sure others will agree, disagree, or want to discuss for discussion and clarification of thought purposes...and at least with the flexibility of the system, there is no 100% right or 100% wrong answer. :) B

1 0

Kenwood TKR-720 COS Interfacing
by Chris Andrist 24 Aug '13

24 Aug '13

I am having problems interfacing my TKR-720 to app_rpt with a URIx. It does not detect a signal on pin 13 of the repeater. I am using COS so letting the URIx do the work for me will not work. Has anybody interfaced one before? If so, did you have to do anything special? Regards, Chris Andrist, KC7WSU

2 1

DTMF commands
by Benjamin L. Naber 24 Aug '13

24 Aug '13

Greetings All, I would like to know if it is 1.) Possible, and 2.) what file(s) need to be modified to change how DTMF commands are interpreted by the system. I'm working on a system in which the users do not have the * or # DTMF commands available on their radios. At this time, the users only options will be: connect to and disconnect from a node. The node numbers may be 2XXXX an above. In under for a user to connect to a node, the dial plan must see five digits as a valid node number, starting with the correct node number start. For this case, we'll use 20000 as the first node. So I thought of the users using '1(X)(..)' for commands. '1' followed by the node number to connect, and '12' to disconnect, for example. Could asterisk be made to recognize single or double digit DTMF tones as commands without using * ? ~Benjamin, KB9LFZ allstar node 28569

2 1

Looking for weatherproof outdoor cabinets
by Sam Skolfield 24 Aug '13

24 Aug '13

Hello Group, By any chance does anybody in the a) Los Angeles county b) Ventura County c) Orange County d) San Bernardino County or e) Riverside County areas have an extra Motorola J series (or equivalent manufacturer) outdoor cabinet available that's in usable shape to use for a repeater installation at a residential location? Or, better yet, two? I can pick up on a mutually agreeable schedule. Thanks! -- KJ6QFS Sam Skolfield

1 0

Audio level test tone with Beagleboard xm and LOX board.
by C B 19 Aug '13

19 Aug '13

Hi Tried to get the test tone as per some of the instructions I have read thus far. I have looked at the rpt.conf file and it looks like it is set up to use *99 as it has the line in it *99=cop,6. The line with *989=cop,4 had a ; (semicolon) in for of it so I assume it is disabled. When I type on the CLI rpt fun 29876 *99 it does not send tone. Please tell me what I have done wrong. Thank you in advance for your help. Chris

3 3