February 2014 - App_rpt-users - lists.keekles.org

Loosing TX
by Bob Roszkowski 10 Feb '14

10 Feb '14

Group, I have a site that is acting strange. I have a server with a VHF(Mastr II) and UHF(TKR-850) repeater, each with a URI. Both repeaters are linked together locally. I noticed while someone is using the machine, the TX will just stop while they are talking. If I switch to the other repeater, the TX is working fine. The URIs Red LED goes out. This happens to both machines. I have swapped and changed URIs and cables with no change. Any ideas? boB - W5EVH

4 5

Re: [App_rpt-users] Loosing TX
by Bob Roszkowski 10 Feb '14

10 Feb '14

Hi Michael, Thanks for the information to test the URI. It does not seem the URI is the issue. I have swapped the URIs with new ones and they all did the same thing. I believe this issue is with the PC hardware or software. Might be a USB bus problem. I will look further into it. boB - W5EVH On Fri, Feb 7, 2014 at 7:45 PM, Michael Hebert <mhebert1975(a)gmail.com>wrote: > You can try the uridiag program. > > Q: How can I test my URI? > A: Download the uridiag program located at > > http://svn.ohnosec.org/viewvc/projects/allstar/uridiag/trunk/?root=svn&view… > > Un-tar it and then 'make' it. Run ./uridiag and select option C. That will > tell you how to make a > loop-back connector for running the diagnostics. This is the same program > we use to test each > URI before it leaves the factory. > > Q: How can I make a loop-back cable to test my URI? > A: Get a male DB-25 connector such as L717SDB25P from www.digikey.com . > Then wire up > the following connections: > Pin 1 to Pin 7 > Pin 2 to Pin 3 > Pin 4 to Pin 8 > Pin 23 to Pin 24 > 10K Resistor between Pins 21 and 22 > 10K Resistor between Pins 21 and 23 > For URIx (CM119) only, also include the following connections: > Pin 5 to Pin 10 > Pin 6 to Pin 11 > > > > On Fri, Feb 7, 2014 at 3:22 PM, Bob Roszkowski <bob(a)w5evh.org> wrote: > >> Group, >> >> I have a site that is acting strange. I have a server with a VHF(Mastr >> II) and UHF(TKR-850) repeater, each with a URI. Both repeaters are linked >> together locally. I noticed while someone is using the machine, the TX >> will just stop while they are talking. If I switch to the other repeater, >> the TX is working fine. The URIs Red LED goes out. This happens to both >> machines. I have swapped and changed URIs and cables with no change. Any >> ideas? >> >> boB - W5EVH >> >> _______________________________________________ >> App_rpt-users mailing list >> App_rpt-users(a)ohnosec.org >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >> >> To unsubscribe from this list please visit >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll >> down to the bottom of the page. Enter your email address and press the >> "Unsubscribe or edit options button" >> You do not need a password to unsubscribe, you can do it via email >> confirmation. If you have trouble unsubscribing, please send a message to >> the list detailing the problem. >> > >

1 0

27305
by ea8ee 10 Feb '14

10 Feb '14

I just reinstall all my node 27305 has been successfully checked however does not appear in the list of the stats page allstarlink.org not understand that it may be happening any ideas thanks

3 4

Re: [App_rpt-users] 27305
by ea8ee 10 Feb '14

10 Feb '14

How can register my node now?? Yesterday can see as registered but now appear as unregistered 2014-02-10 16:27 GMT+00:00 ea8ee <ea8ee1(a)gmail.com>: > Jim > > it appear > host dnsmgr unregistered > > 0.0.0.0:4569 N > > But I dont understand two thing first yesterday my node is registered and > second appear 4569 but I use 4570 as UDP > how I can to register it and change the UDP port > > > 2014-02-10 16:02 GMT+00:00 Tim Sawyer <tim.sawyer(a)mac.com>: > > I see your node is not registered. You can see registration by looking at >> https://allstarlink.org/nodelist.php. There needs to be a green >> background on your node number. Or you can use the Asterisk CLI (i.e. *CLI> >> iax2 show registry). >> >> Registration has to happen before anything else will work including >> stats. Internet connectivity is necessary to register with the Allstar >> system. See if you can ping google.com on anything else outside of your >> LAN. If not it's probably a DNS problem. New ACID installs sometimes don't >> have DNS entries in /etc/resolv.conf. >> >> It should look something like this: >> nameserver 8.8.8.8 >> nameserver 8.8.4.4 >> >> >> -- >> Tim >> :wq >> >> On Feb 10, 2014, at 7:12 AM, ea8ee <ea8ee1(a)gmail.com> wrote: >> >> These two lines are active using ACID ! >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> >> X >> >> >> >> >> >> >> >> >> X >> >> >> >> >> >> >> >> >> >> >> 2014-02-10 14:57 GMT+00:00 Tim Sawyer <tim.sawyer(a)mac.com>: >> >>> Uncomment two lines in /etc/asterisk/rpt.conf: >>> >>> ; >>> ; *** Status Reporting *** >>> ; >>> ; Uncomment the either group following two statpost lines to report the >>> status of your node to stats.allstarlink.org >>> ; depending on whether you are running ACID or Limey Linux. >>> >>> ; ** For ACID *** >>> statpost_program=/usr/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null >>> >>> statpost_url=http://stats.allstarlink.org/uhandler.php ; Status updates >>> >>> ; ** For Limey Linux ** >>> ;statpost_program=/bin/wget,-q,--timeout=15,--tries=1,--output-document=/dev/null >>> >>> ;statpost_url=http://stats.allstarlink.org/uhandler.php ; Status >>> updates >>> >>> -- >>> Tim >>> :wq >>> >>> On Feb 10, 2014, at 6:06 AM, ea8ee <ea8ee1(a)gmail.com> wrote: >>> >>> I just reinstall all my node 27305 has been successfully checked however does >>> not appear in the list of the stats page allstarlink.org not understand >>> that it may be happening any ideas thanks >>> _______________________________________________ >>> App_rpt-users mailing list >>> App_rpt-users(a)ohnosec.org >>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >>> >>> To unsubscribe from this list please visit >>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll >>> down to the bottom of the page. Enter your email address and press the >>> "Unsubscribe or edit options button" >>> You do not need a password to unsubscribe, you can do it via email >>> confirmation. If you have trouble unsubscribing, please send a message to >>> the list detailing the problem. >>> >>> >>> >> >> >

1 0

Re: [App_rpt-users] app_rpt parallel port usage
by mike＠midnighteng.com 10 Feb '14

10 Feb '14

3 2

Re: [App_rpt-users] allmon
by Bradley Haney 10 Feb '14

10 Feb '14

have you had any problem of pushing the X button to disconnect and it doesn't do anything?

2 1

install acid
by ea8ee 10 Feb '14

10 Feb '14

I just reinstall the acid but remains part of downloading files from the Internet tries and retries but seems to have no internet I checked the network cable and internet connection is correct as well as the green flash connector, not where you can be the fault

2 2

Re: [App_rpt-users] allmon
by Bradley Haney 10 Feb '14

10 Feb '14

i can connect just fine but i press the X to disconnect and doesn't work.. any thoughts

1 0

Host not acknowledging non-GPS disciplined operation
by Craig Sande 10 Feb '14

10 Feb '14

I am new to All-Star and have set up a server on an Intel i3 and am trying to get it to work with my RTCM acquired from Micro-Node. I had it linking to Mark's server at Micro-Node, but when I tried to set up my server using the same settings in voter.conf and rpt.conf I get the following error message on the RTCM repeatedly scrolling down the screen: <System Time Not Set> ERROR! Host not acknowledging non-GPS disciplined operation. If I change the Host password on the RTCM, it will stop scrolling the error message, but of course is not connected. I am uncertain as to where I should look to debug the issue. Any thoughts? Craig Sande AE7I Node 40586

2 2

SIP Help Needed
by Bill Hurlock 10 Feb '14

10 Feb '14

I use CSIP Simple on my cell Phone. When I'm on my local WiFi all is well. If I go on the road and log into a WiFi system somewhere. I can register the account but it only seems to be a inward path only. When I watch CLI remotely, I see the connect, Answer, Wait, Playback going out OK but hear nothing on the Cell phone end. Than I see some CLI error messages that seem to point to the fact it isn't getting info back from the Cell phone end after which it processes a disconnect. Is this a port issue at the distant end of the link or something I have wrong on the Server end?? As I mentioned it works perfect when logged in on WiFI on the same network as the server. IAX clients seem to be having a similar issue connecting from the cell however IAXRpt works OK from the cell phone network using my PC to connect home to the server. Any ideas on this as I know people are using SIP OK out in the field. Bill Hurlock CPCommunications 856-234-1661 Office 856-264-1010<http://www.totalrf.com/> Cell www.cpcomms.com<http://www.cpcomms.com/> WA2TQI

3 3