September 2014 - App_rpt-users

Re: [App_rpt-users] MSF to RTCM Wiring
by Robert 16 Sep '14

16 Sep '14

The repeater will be one of three. Each will communicate with a master server in a commercial data center where our business is located. If I have read correctly this is a hub? At any rate the CLB's will be run with RTCM as non-voted but with synchronized TX. I have the Motorola modules for this. _____ From: KJ6KO [mailto:kj6ko@innercite.com] Sent: Tuesday, September 16, 2014 8:27 AM To: Robert Subject: Re: [App_rpt-users] MSF to RTCM Wiring Hi Robert, It mainly depends on how you are going to use the system. If it is just a stand alone repeater, the RTCM is a bit of overkill, but will work fine. I have done a couple of MSF's. Assuming this is just a standalone CLB repeater (the one with the EPROM), and not a voted system, I like to keep things as simple as possible. Program the repeater to be a "Base Station", NOT a repeater!. Pull RX audio from the DISCRIMINATOR output of the MSF and make sure the RTCM is set to PLFILTER=YES and DEEPPHASIS=YES. The COR/PL Detect on a MSF is a bit trickey. You have to pull it off of a chip and use a transistor to switch it. For TX, just use the PTT and MIC Input. That is the simplest way. You can also feed raw TX audio directly into the modulator from the RTCM and have the RTCM generate the TX PL if you like, but that is a bit more complicated. I have done it, but I don't really see much of an advantage. ALl these connections are Test Points on the MSF, (Except the COR/PL) and that makes connection easy. ALSO, set the squelch on the RTCM a bit high! The RTCM's squelch circuit is a bit touchy. NOW, if you have a CXB (programmable MSF) it is all basically the same except that you can program an output of the MSF for "Valid PL Signal" and use that as the COR/PL input to the RTCM. I don't use the internal controller as the repeater. I have never been real satisfied with the audio quality of the MSF repeated audio. Best to let the RTCM do all the work and digitally filter the DISC audio rather than let the MSF do it! The RTCM will do all the controlling, tail, ID and courtesy tones for you. Also, don't forget to disable the MSF's TX Timer! Unless you are using a voting system, the URI is a MUCH cheaper source and does everything you want for just a standalone repeater, assuming you have a computer to go with it. I use the Beaglebone! The URI as it will also act as the controller, filter the DISC audio and one thing it does that the RTCM won't do is you have REMOTE audio control! That way, after you install the repeater on a hilltop, and you think the audio is a bit high or low, you can remotely bump it up or down to your hearts content! The RTCM is all manual control! Good luck and 73... Greg KJ6KO ----- Original Message ----- From: Robert <mailto:robert@controlservers.net> To: app_rpt-users(a)ohnosec.org Sent: Monday, September 15, 2014 11:01 PM Subject: [App_rpt-users] MSF to RTCM Wiring I have seen so many different ways of how to wire a controller / RTCM to a MSF 5000 - is there one sure fired way to do this? Poor eyesight on my part. I hate being the new guy. __________ Information from ESET NOD32 Antivirus, version of virus signature database 10426 (20140916) __________ The message was checked by ESET NOD32 Antivirus. http://www.eset.com _____ _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. __________ Information from ESET NOD32 Antivirus, version of virus signature database 10426 (20140916) __________ The message was checked by ESET NOD32 Antivirus. http://www.eset.com __________ Information from ESET NOD32 Antivirus, version of virus signature database 10426 (20140916) __________ The message was checked by ESET NOD32 Antivirus. http://www.eset.com

1 0

Re: [App_rpt-users] Trouble shooting
by mike＠midnighteng.com 16 Sep '14

16 Sep '14

2 1

Trouble shooting
by Loren Tedford 16 Sep '14

16 Sep '14

Hey its Loren here I am working on our repeater system out here in Olney IL we put in a pico power supply and a few other things including a motherboard we reinstalled from the Acid cd and for some reason we are not passing audio full duplex through the RX side of the repeater suddenly.. Seems strange because the repeater can still capture DTMF makes me wonder if maybe its trying to pick up a ctcss tone or some thing idk did all the trouble shooting I could think of all night last night and still no luck any ideas???? Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com http://www.lorentedford.com http://kc9zhv.lorentedford.com

2 1

MSF to RTCM Wiring
by Robert 16 Sep '14

16 Sep '14

I have seen so many different ways of how to wire a controller / RTCM to a MSF 5000 - is there one sure fired way to do this? Poor eyesight on my part. I hate being the new guy.

1 0

Virtual node
by Steve Zingman 16 Sep '14

16 Sep '14

Been there, doing that. I've been running Node 2100 as a hub on a VMware VM for years. First as Debian Etch and now Wheezy. Steve N4IRS On 09/14/2014 12:00 PM, app_rpt-users-request(a)ohnosec.org wrote: > Send App_rpt-users mailing list submissions to > app_rpt-users(a)ohnosec.org > > To subscribe or unsubscribe via the World Wide Web, visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > or, via email, send a message with subject or body 'help' to > app_rpt-users-request(a)ohnosec.org > > You can reach the person managing the list at > app_rpt-users-owner(a)ohnosec.org > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of App_rpt-users digest..." > > > Today's Topics: > > 1. Re: Centos 5 with kernel 2.6.32-042stab093.4 (Lu Vencl) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Sun, 14 Sep 2014 07:42:08 -0400 > From: Lu Vencl <vencl(a)att.net> > To: Bryan Fields <Bryan(a)bryanfields.net> > Cc: APP RPT <app_rpt-users(a)ohnosec.org> > Subject: Re: [App_rpt-users] Centos 5 with kernel 2.6.32-042stab093.4 > Message-ID: <0EBFA15D-28D2-4381-A9B5-D59B12701A40(a)att.net> > Content-Type: text/plain; charset=utf-8 > > Been there and done it. It does not work. > > Lu Vencl > >> On Sep 13, 2014, at 11:25 PM, Bryan Fields <Bryan(a)bryanfields.net> wrote: >> >>> On 9/13/14, 11:19 PM, Tim Sawyer wrote: >>> People have jumped on my butt for saying this before but I?ll say it again >>> anyway. It?s very unlikely Asterisk will run worth a damn on a VPS, >>> especially one for $5/mo. I?m not going to tell you not to do it, but if >>> you do manage to jump the hurdles of getting Asterisk installed on a hosted >>> VPS, it may not work as it does on a $50 computer. >> >> I second this. Asterisk is one of those programs that is very timing >> dependent. A virtual server, especially a $5/month VPS is not going to work >> well since there are 200 VM's all competing for processor time. >> >> This being said, there is no requirement that you run ACID. Grab it and >> compile from source, I dislike redhat/centos, and run on debian just fine. >> >> -- >> Bryan Fields >> >> 727-409-1194 - Voice >> 727-214-2508 - Fax >> http://bryanfields.net >> _______________________________________________ >> App_rpt-users mailing list >> App_rpt-users(a)ohnosec.org >> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >> >> To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" >> You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. > > > ------------------------------ > > _______________________________________________ > App_rpt-users mailing list > App_rpt-users(a)ohnosec.org > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users > > > End of App_rpt-users Digest, Vol 67, Issue 44 > ********************************************* >

5 13

Connection failed
by Robert Newberry 15 Sep '14

15 Sep '14

So the power was cut to the building my repeater is in. My repeater functions, I'm able to connect via IAX. I'm also able to SSH in and ping the IP of the node I'm trying to connect too (27066) I'm also able to ping google.com. but when I go to the CLI and type rpt fun 27086 *327066 it fails. So what gives? I'm running acid and a DMK URI.

4 5

Ideas (Mobile App)
by Loren Tedford 15 Sep '14

15 Sep '14

Since allstar is pretty well accessible with sip clients i wonder how easy it would be to build a mobile app that we could use on both Iphones and Andriod based OS I know that this would involve alot of work probably however I think it would help out Allstar greatly especially if we were to compare it to Echolink where thats all the old timers talk about.. Echolink to them is just name recognition but just like Windows it has its flaws... This is only just an Idea if some one else has thought of this i apologize for stepping on anybody toes... I just know that to keep some project like this going requires pushing the edges of technology is good especially for long term.. I wish i knew enough about programming if i did i personally would love to help out but I am not that good when it comes down to that sort of things.. Anyway thanks for the help everyone on earlier projects Loren Tedford (KC9ZHV) Email: lorentedford(a)gmail.com <loren(a)richlandcountycomputers.com> http://www.lorentedford.com http://kc9zhv.lorentedford.com

3 3

Re: [App_rpt-users] rc.updatenodelist fails.
by Bryan Fields 15 Sep '14

15 Sep '14

I've had three other people on IRC test this and I've tested this from 3 different servers myself. All are giving an error 403 on: http://nodes1.allstarlink.org/cgi-bin/nodes.pl I don't think it's just me :( On 9/13/14, 11:50 PM, Bob wrote: > Works fine here. > > -----Original Message----- > From: app_rpt-users-bounces(a)ohnosec.org > [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of Bryan Fields > Sent: Saturday, September 13, 2014 8:32 PM > To: Tim Sawyer; APP RPT > Subject: Re: [App_rpt-users] rc.updatenodelist fails. > > Thanks Tim, > > However, I'm getting 403 errors on each. > > Perhaps some kinda IP block issue or something? > > root@KB9MCI:/etc/rc.d# wget http://nodes1.allstarlink.org/cgi-bin/nodes.pl > --2014-09-13 23:26:54-- http://nodes1.allstarlink.org/cgi-bin/nodes.pl > Resolving nodes1.allstarlink.org... 96.36.57.202 > Connecting to nodes1.allstarlink.org|96.36.57.202|:80... connected. > HTTP request sent, awaiting response... 403 > 2014-09-13 23:26:54 ERROR 403: (no description). > > root@KB9MCI:/etc/rc.d# wget http://nodes2.allstarlink.org/cgi-bin/nodes.pl > --2014-09-13 23:27:00-- http://nodes2.allstarlink.org/cgi-bin/nodes.pl > Resolving nodes2.allstarlink.org... 209.159.155.200 > Connecting to nodes2.allstarlink.org|209.159.155.200|:80... connected. > HTTP request sent, awaiting response... 403 Forbidden > 2014-09-13 23:27:00 ERROR 403: Forbidden. > > root@KB9MCI:/etc/rc.d# wget http://nodes3.allstarlink.org/cgi-bin/nodes.pl > --2014-09-13 23:27:06-- http://nodes3.allstarlink.org/cgi-bin/nodes.pl > Resolving nodes3.allstarlink.org... 65.110.110.172 > Connecting to nodes3.allstarlink.org|65.110.110.172|:80... connected. > HTTP request sent, awaiting response... 403 > 2014-09-13 23:27:06 ERROR 403: (no description). > > root@KB9MCI:/etc/rc.d# wget http://nodes4.allstarlink.org/cgi-bin/nodes.pl > --2014-09-13 23:27:11-- http://nodes4.allstarlink.org/cgi-bin/nodes.pl > Resolving nodes4.allstarlink.org... 67.214.190.109 > Connecting to nodes4.allstarlink.org|67.214.190.109|:80... connected. > HTTP request sent, awaiting response... 403 Forbidden > 2014-09-13 23:27:12 ERROR 403: Forbidden. > > > > > > On 9/13/14, 11:23 PM, Tim Sawyer wrote: >> Works for me. >> >> >> Resolving nodes1.allstarlink.org... 96.36.57.202 >> Connecting to nodes1.allstarlink.org|96.36.57.202|:80... connected. >> HTTP request sent, awaiting response... 200 OK >> Length: unspecified [text/plain] >> Saving to: `/var/lib/asterisk/rpt_extnodes-temp' >> >> [ <=> > ] 64,417 225K/s in 0.3s >> >> 2014-09-13 20:19:36 (225 KB/s) - `/var/lib/asterisk/rpt_extnodes-temp' > saved [64417] >> >> Retrieved node list from nodes1.allstarlink.org >> >> -- >> Tim WD6AWP >> >>> On Sep 13, 2014, at 8:13 PM, Bryan Fields <Bryan(a)bryanfields.net> wrote: >>> >>> This is not working, looks like all the servers are not responding. >>> >>> Problem retrieving node list from nodes1.allstarlink.org, trying another > server >>> Problem retrieving node list from nodes2.allstarlink.org, trying another > server >>> Problem retrieving node list from nodes3.allstarlink.org, trying another > server >>> Problem retrieving node list from nodes4.allstarlink.org, trying another > server >>> Problem retrieving node list from nodes1.allstarlink.org, trying another > server >>> >>> Ideas? >>> >>> -- >>> Bryan Fields >>> >>> 727-409-1194 - Voice >>> 727-214-2508 - Fax >>> http://bryanfields.net >>> >>> _______________________________________________ >>> App_rpt-users mailing list >>> App_rpt-users(a)ohnosec.org >>> http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users >>> >>> To unsubscribe from this list please visit > http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to > the bottom of the page. Enter your email address and press the "Unsubscribe > or edit options button" >>> You do not need a password to unsubscribe, you can do it via email > confirmation. If you have trouble unsubscribing, please send a message to > the list detailing the problem. >> > > -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net

7 10

Re: [App_rpt-users] Centos 5 with kernel 2.6.32-042stab093.4
by Doug Crompton 14 Sep '14

14 Sep '14

Pete, I have done this so many times but unfortunately I never documented it. Here is a simple description. Get a distro and configure it like you normally would. Get ntpd running, network setup, etc. Download the acid code and the latest dahdi - I see it is 2.10.0 The last I used was 2.9.x but I suspect it will work the same. If not you could get the 2.9 version. http://www.asterisk.org/downloads/dahdi Apply the patch - info on how to do that is in the readme https://allstarlink.org/fixed-dahdi-patches.tar.gz Compile and install dahdi. Then compile and install asterisk Don't run any offsite updates. Configure it manually - not hard to do - and run. If you already have a configured system you can use those files from /etc.asterisk. BTW the BBB setup procedure and howto's at http://hamvoip.org describe how to do that very easily which would also apply here. The only caveat is the config files would be different to start with so some consideration has to be given to that. All that sounds easy but you undoubtedly will have some hiccups and things you will have to do to get it to work. It is impossible to document that as it would be different on the multitude of distros and kernel versions. I have compiled it on the latest Debian and Ubuntu. The real problem is OSS support which is required. Debian has it, Ubuntu does not. You have to recompile the kernel and add it back in. For that reason Ubuntu is not recommended as kernel versions can change with frequent updates. I guess the big question is do you really need to do this. I forget why you said you can't run a local system. In that case you could just install an acid release on a PC or maybe go with the BBB. 73 Doug WA3DSP http://www.crompton.com/hamradio From: petem001(a)hotmail.com To: doug(a)crompton.com Subject: Re: [App_rpt-users] Centos 5 with kernel 2.6.32-042stab093.4 Date: Thu, 11 Sep 2014 12:08:04 -0400 well can you point me a few pointers on how to do so? Never patched some software before. From: Doug Crompton Sent: Thursday, September 11, 2014 11:03 AM To: pete M Cc: app_rpt-users(a)ohnosec.org Subject: RE: [App_rpt-users] Centos 5 with kernel 2.6.32-042stab093.4 I am not sure what you are saying when you comment.... "well I think that Dahdi wont compile correctly on Any distro that have a kernel pass a certain point.." Did you mean "will" ?? The patches can be applied against the latest dahdi and it will compile on late kernels. The BBB is an example of that. 73 Doug WA3DSP http://www.crompton.com/hamradio From: petem001(a)hotmail.com To: doug(a)crompton.com CC: app_rpt-users(a)ohnosec.org Subject: Re: [App_rpt-users] Centos 5 with kernel 2.6.32-042stab093.4 Date: Thu, 11 Sep 2014 09:42:08 -0400 well I think that Dahdi wont compile correctly on Any distro that have a kernel pass a certain point.. I can run the system on bunch of disto.. Here is the list.. CentOS 5 32bit CentOS 5 64bit CentOS 6 32bit CentOS 6 64bit CentOS 7 64bit CentOS 7 64bit Minimal Debian 6 32bit Debian 6 64bit Debian 7 32bit Debian 7 32bit Minimal Debian 7 64bit Debian 7 64bit Minimal Fedora 17 32bit Fedora 17 64bit Fedora 19 32bit Fedora 19 64bit Starbound-Ubuntu 13.10 32bit SUSE 12.2 32bit SUSE 12.2 64bit Ubuntu 10.04 32bit Ubuntu 10.04 64bit Ubuntu 11.10 32bit Ubuntu 11.10 64bit Ubuntu 12.10 32bit Ubuntu 12.10 64bit Ubuntu 13.10 32bit Ubuntu 13.10 64bit Ubuntu 14.04 32bit Ubuntu 14.04 32bit Minimal Ubuntu 14.04 64bit Ubuntu 14.04 64bit Minimal So I have lots of choice But I was under the feeling that the best distro was centos 5 for acid.. (using the install script from the cd.. Unless you can point me in another direction.. From: Doug Crompton Sent: Wednesday, September 10, 2014 6:16 PM To: pete M Cc: app_rpt-users(a)ohnosec.org Subject: RE: [App_rpt-users] Centos 5 with kernel 2.6.32-042stab093.4 Pete, I have been somewhat following this. Does it have to be centos? Allstar will run on the latest Debian. You need to install it yourself but depending on your Linux capability it is not a big deal. 73 Doug WA3DSP http://www.crompton.com/hamradio From: petem001(a)hotmail.com To: kk6ecm(a)gmail.com; app_rpt-users(a)ohnosec.org Date: Wed, 10 Sep 2014 14:12:38 -0400 Subject: Re: [App_rpt-users] Centos 5 with kernel 2.6.32-042stab093.4 Thanks Bob. I dont think that it has to do with something impossible to do.. In fact I have been searching the archives about problem like that.. And there was some answer about some patch to dahdi zaptel.. or such.. I am at work, dont remember.. If it would be installed at least up to a point. I would be able to do it.. I just dont know how to tell the compiler not to compile that part and go on.. From: kk6ecm(a)gmail.com Date: Wed, 10 Sep 2014 09:15:13 -0700 To: app_rpt-users(a)ohnosec.org Subject: Re: [App_rpt-users] Centos 5 with kernel 2.6.32-042stab093.4 Couple of thoughts. I've not been able to load using ssh. Last time I attempted this zaptel did not load properly, but it seems I didn't get an error until after the reboot. It seems to me (check the ACID scripts), that ACID disables ssh during the load. When I have loaded CentOS 5.10 (as previously mentioned), I then used some of the ACID scripts to load asterisk, etc, I always had to us a monitor and keyboard on the server to be fully successful. But hey... that could just be my fumbling around. As for your stated concern. I could be because no one knows the answer. Hard to believe, I know, but it seems to happen occasionally on this list :~} Thanks, Bob kk6ecm Sent from iPad On Sep 10, 2014, at 8:30 AM, pete M <petem001(a)hotmail.com> wrote: OK, did I asked a question that CAN’T be answered? Or did I asked the wrong way? If I did I am sorry.. And I gave my apology to every one I could have offended.. But is it possible to at least have a small word from all those guru here if it can be done, and which way should I go? dont need to have someone holding my hand.. Just need to have a small Idea what to do.. Like just point me the pathway.. I will try to do it on my own.. Thanks On Sep 9, 2014, at 11:13 AM, pete M <petem001(a)hotmail.com> wrote: I cant use the acid.iso cause the computer is in a remote place ( rented server) and they dont supply special OS installation. I can have fedore ubuntu centos on many flavor (x86 or 64 bit) and many revision... The problem is not the loading od the cd are other things like that.. I am sure that the kernel is too new and there is a part of zaptel that need a depricated fonction If I am not crazy.. From: kk6ecm Sen t: Tuesday, September 09, 2014 1:40 PM To: APP RPT Subject: Re: [App_rpt-users] Centos 5 with kernel 2.6.32-042stab093.4 I use this when ACID will not load, usually due to issues with BIO S and network drivers. I was assuming you were not able to get ACID to load on you computer. If your running phase2.sh was a second attempt after trying to load ACID, you may need to check that all the files are there because the load deletes some files. In short, if this occurred during an attempt to load the ACID download, I'd just try it again. Thanks, Bob kk6ecm Sent from iPad On Sep 9, 2014, at 8:27 AM, pete M <petem001(a)hotmail.com> wrote: Ok will try that.. thanks! From: Bob Sent: Tuesday, September 09, 2014 10:55 AM To: 'APP RPT' Subject: Re: [App_rpt-users] Centos 5 with kernel 2.6.32-042stab093.4 I’ve done this several times without issue. Here are the steps I used. Load CentOS 5.10 downloaded from CentOS website No features, tools only, no desktop (competes with Asterisk) Set ssh /etc/ssh/sshd_config Run "setup" at comand line and disable firewall vi /etc/rc.d/acidrepo http://dl.allstarlink.org Execute portion of ks.cfg, each line at a time cp /etc/rc.d/rc.local /etc/rc.d/rc.local.orig cat <<EOF >>/etc/rc.d/rc.local cd /etc/rc.d; rm -f phase1.sh; wget -q http://dl.allstarlink.org/installcd/phase1.sh chmod 755 /etc/rc.d/phase1.sh /etc/rc.d/phase1.sh Auto reboot after phase1.sh executed phase2.sh runs automatically to completion Bob kk6ecm From: app_rpt-users-bounces(a)ohnosec.org [mailto:app_rpt-users-bounces@ohnosec.org] On Behalf Of pete M Sent: Tuesday, September 09, 2014 7:00 AM To: APP RPT Subject: [App_rpt-users] Centos 5 with kernel 2.6.32-042stab093.4 Need help to install an allstarlink node that wont have any radio on it in a data center to be my central reflector for my french network of repeater around Quebec Canada.. I did try to run phase2.sh from /etc/rc.d/ but this fail when compiling. here is the out put from the script sh phase2.sh ****** Phase 2 post install ****** Getting asterisk install script from http://dl.allstarlink.org../. Getting files.tar.gz from http://dl.allstarlink.org../. ****** Asterisk Installation ****** /etc/rc.d/astinstall.sh: line 11: ntpdate: command not found Unpacking files.tar.gz... Compiling Zaptel... checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes checking whether we are cross compiling... no checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether gcc accepts -g... yes checking for gcc option to accept ISO C89... none needed checking how to run the C preproc esso r... gcc -E checking for a BSD-compatible install... /usr/bin/install -c checking whether ln -s works... yes checking for GNU make... make checking for grep... /bin/grep checking for sh... /bin/sh checking for ln... /bin/ln checking for wget... /usr/bin/wget checking for grep that handles long lines and -e... (cached) /bin/grep checking for egrep... /bin/grep -E checking for ANSI C header files... yes checking for sys/types.h... yes checking for sys/stat.h... yes checking for stdlib.h... yes checking for string.h... yes checking for memory.h... yes checking for strings.h... yes checking for inttypes.h... yes checking for stdint.h... yes checking for unistd.h... yes checking for initscr in -lcurses... no checking for initscr in -lncurses... no checking for newtBell in -lnewt... no checking for usb_init in -lusb... no configure: creating ./config.status config.status: creating build_tools/menuselect-deps config.status: creating makeopts config.status: creating build_tools/make_firmware_object configure: *** Zaptel build successfully configured *** make[1]: Entering directory `/usr/src/astsrc/zaptel/menuselect' checking build system type... i686-pc-linux-gnu checking host system type... i686-pc-linux-gnu checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes checking whether we are cross compiling... no checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether gcc accepts -g... yes checking for gcc option to accept ANSI C... none needed checking for GNU make... make checking for asprintf... yes checking for getloadavg... yes checking for setenv... yes checking for strcasestr... yes checking for strndup... yes checking for strnlen... yes checking for strsep... yes checking for strtoq... yes checking for unsetenv... yes checking for vasprintf... yes checking how to run the C preprocessor... gcc -E checking for egrep... grep -E checking for ANSI C header files... yes checking for sys/types.h... yes checking for sys/stat.h... yes checking for stdlib.h... yes checking for string.h... yes checking for memory.h... yes checking for strings.h... yes checking for inttypes.h... yes checking for stdint.h... yes checking for unistd.h... yes checking for initscr in -lcurses... no checking for initscr in -lncurses... no checking for pkg-config... No configure: creating ./config.status config.status: creating makeopts config.status: creating autoconfig.h configure: configuring in mxml configure: running /bin/sh './configure' --prefix=/usr/local 'CC=' 'LD=' 'AR=' 'CFLAGS=' --cache-file=/dev/null --srcdir=. checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes checking whether we are cross compiling... no checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether gcc accepts -g... yes checking for gcc option to accept ANSI C... none needed checking for g++... no checking for c++... no checking for gpp... no checking for aCC... no checking for CC... no checking for cxx... no checking for cc++... no checking for cl... no checking for FCC... no checking for KCC... no checking for RCC... no checking for xlC_r... no checking for xlC... no checking whether we are using the GNU C++ compiler... no checking whether g++ accepts -g... no checking for a BSD-compatible install... /usr/bin/install -c checking for ranlib... ranlib checking for ar... /usr/bin/ar checking for cp... /bin/cp checking for ln... /bin/ln< /font> checking for mkdir... /bin/mkdir checking for nroff... /usr/bin/nroff checking for rm... /bin/rm checking for strdup... yes checking for vsnprintf... yes configure: creating ./config.status config.status: creating Makefile config.status: creating mxml.list config.status: creating mxml.pc config.status: creating config.h configure: Menuselect build configuration successfully completed make[1]: Leaving directory `/usr/src/astsrc/zaptel/menuselect' make[1]: Entering directory `/usr/src/astsrc/zaptel/menuselect' make[2]: Entering directory `/usr/src/astsrc/zaptel/menuselect' gcc -g -c -D_GNU_SOURCE -Wall -c -o menuselect.o menuselect.c gcc -g -c -D_GNU_SOURCE -Wall -c -o strcompat.o strcompat.c gcc -g -c -D_GNU_SOURCE -Wall -c -o menuselect_stub.o menuselect_stub.c make[3]: Entering directory `/usr/src/astsrc/zaptel/menuselect/mxml' gcc -O -Wall -c mxml-attr.c gcc -O -Wall -c mxml-entity.c gcc -O -Wall -c mxml-file.c gcc -O -Wall -c mxml-index.c gcc -O -Wall -c mxml-node.c gcc -O -Wall -c mxml-search.c gcc -O -Wall -c mxml-set.c gcc -O -Wall -c mxml-private.c gcc -O -Wall -c mxml-string.c /bin/rm -f libmxml.a /usr/bin/ar crvs libmxml.a mxml-attr.o mxml-entity.o mxml-file.o mxml-index.o mxml-node.o mxml-search.o mxml-set.o mxml-private.o mxml-string.o a - mxml-attr.o a - mxml-entity.o a - mxml-file.o a - mxml-index.o a - mxml-node.o a - mxml-search.o a - mxml-set.o a - mxml-private.o a - mxml-string.o ranlib libmxml.a make[3]: Leaving directory `/usr/src/astsrc/zaptel/menuselect/mxml' gcc -o menuselect menuselect.o strcompat.o menuselect_stub.o mxml/libmxml.a mxml/libmxml.a make[2]: Leaving directory `/usr/src/astsrc/zaptel/menuselect' make[1]: Leaving directory `/usr/src/astsrc/zaptel/menuselect' Generating input for menuselect ... *********************************************************** The existing menuselect.makeopts file did not specify that 'zttool' should not be included. However, either some dependencies for this module were not found or a conflict exists. Either run 'make menuselect' or remove the existing menuselect.makeopts file to resolve this issue. *********************************************************** make: *** [menuselect.makeopts] Error 255 Failure: Unable to compile Zaptel 2 Fatal error: Unable to install Asterisk! [root@node rc.d]# I dont know where to go from there.. Anyone care to help a bit? _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem. _______________________________________________ App_rpt-users mailing list App_rpt-users(a)ohnosec.org http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users To unsubscribe from this list please visit http://ohnosec.org/cgi-bin/mailman/listinfo/app_rpt-users and scroll down to the bottom of the page. Enter your email address and press the "Unsubscribe or edit options button" You do not need a password to unsubscribe, you can do it via email confirmation. If you have trouble unsubscribing, please send a message to the list detailing the problem.

3 8

Re: [App_rpt-users] Centos 5 with kernel 2.6.32-042stab093.4
by Bryan Fields 14 Sep '14

14 Sep '14

On 9/13/14, 11:19 PM, Tim Sawyer wrote: > People have jumped on my butt for saying this before but I’ll say it again > anyway. It’s very unlikely Asterisk will run worth a damn on a VPS, > especially one for $5/mo. I’m not going to tell you not to do it, but if > you do manage to jump the hurdles of getting Asterisk installed on a hosted > VPS, it may not work as it does on a $50 computer. I second this. Asterisk is one of those programs that is very timing dependent. A virtual server, especially a $5/month VPS is not going to work well since there are 200 VM's all competing for processor time. This being said, there is no requirement that you run ACID. Grab it and compile from source, I dislike redhat/centos, and run on debian just fine. -- Bryan Fields 727-409-1194 - Voice 727-214-2508 - Fax http://bryanfields.net

2 1